MADE IN
BRITAIN
Dimensions
Width - 47cm
Depth - 50cm
Height - 75cm
Atlas - Internal 3 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 19/03/14
Important - Please read these instructions fully before starting assembly
161/5803
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 19kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
3
9
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4 5
Top (D2384A)
(496 x 468mm)
7
6
8
Wrap Back (W387-124)
(387 x 124mm) x 3
Rail (D2386A)
(437 x 60mm) x 2
Drawer Front (D2387A)
(433 x 189mm) x 3
Left Drawer
Side (W370-124LH)
(370 x 124mm) x 3
Right Drawer
Side (W370-124RH)
(370 x 124mm) x 3
Drawer Base (T402-367)
(398 x 367mm) x 3
2
Left Side (D2385A)
(735 x 495mm)
Right Side (D2766A)
(735 x 495mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
I
B
Metal dowel (F901) x 10
C
D E
Large locking
nut (F900) x 4
F
G H
Rule Scissors
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small locking
nut (F3) x 6
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
13mm Screw (F52) x 18
13mm Screw (F63) x 18
Knock-in Peg (F171) x 12
J
b
J
c
J
a
J
d
50mm Screw (F49) x 8
Allen Key (F36) x 1
Hammer
A
Wooden dowel (F22) x 2
K
Wedgefix (F639) x 6
CL Runner
(F904) x 3
DL Runner
(F906) x 3
DR Runner
(F905) x 3
CR Runner
(F903) x 3
400mm long
L
Plastic Nail (F91) x 4
4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the
reference numbers below
Step 1
B
4
6
B
B
D
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
4
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
D
5
6
Attach the drawer
sides to the drawer
fronts
Push the left drawer side
and right drawer
side . onto the back of
the drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
5
6
4
D
D
5
6
Groove
5
D
D
B
B
4
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
D
6
5
x 3
x 3 x 3
x 3
4
4
Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer backs
Fit the drawer back .
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
5 6
4
7
5 6
8
7
7
H
5 6
8
H
H
8
5
6
7
5
6
8
x 3
x 3
Step 6
Runners must be
pushed up against
the drawer front
5
6
4
x 3
J d
J c
G
G
G
G
DL
DR
Fit runners to the
drawers
Turn the 3 drawer
assemblies over.
Fit runner d , marked
with ‘DR’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. . Use a bradawl to
mark the fixing positions,
then secure with 2
screws .
Fit runner , marked
‘DL’, to the bottom edge
of the left drawer side
using the same method.
5
J d
6
4
G
J c
DR
DL
Assembly Instructions
6
Step 7
Step 8
Prepare the top
Screw 4 metal dowels
into the top .
B
B
B
B
Plain chipboard
surface
3
B
3
Finished
front edge
Fit the wedgefixes
Slide 1 wedgefix into
the small groove located
on the back of the
drawer front and 1
into the small groove in
the drawer back .
Once in place, tighten up
the screws in the
wedgefixes .
K
4
7
K
4
K
K
7
x 3
Assembly Instructions
7
Step 9
A
a:
b:
J a
F
Finished front edge
F
1st
screw
2nd
screw
F
3rd
screw
J a
Finished front edge
G
G
C
C
C
Prepare the left side
a: Fit runners to
the left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
J a
1
F
F
G
J a
C
1
10mm
A
A
1
1
CL
F
F
F
CL
F
F
F
CL
F
F
F
J
a
J
a
J
a
1
CL
CL
CL
G
G
Finished
front edge
Finished front edge
Assembly Instructions
8
Step 10
A
J b
F
Finished front edge
F
1st
screw
2nd
screw
F
3rd
screw
J b
Finished front edge
G
Finished
front edge
Prepare the right side
a: Fit runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Insert 2 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
J b
2
F
F
G
J b
C
2
Finished
front edge
a:
b:
C
A
2
2
J b
CR
CR
H
F
H
F
H
F
J b
CR
F
F
F
J b
CR
F
F
F
2
CR
CR
CR
G
G
G
C
Assembly Instructions
9
Step 11
Fit the top
Push the top onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
3
C
C
C
B
2
2
3
Finished
front edge
Step 12
Fit the 2 rails
Fit the 2 rails onto
the right side using 4
screws and tighten
using the allen key .
2
9
E
3
Plain
chipboard
surface
I
I
9
I
I
I
E
CR
CR
CR
9
3
3
CR
CR
CR
I
E
I
I
I
1
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
1
C
1
9
9
Fit the 2 rails onto
the left side using 4
screws and tighten
using the allen key .
1
9
E
I
Assembly Instructions
10
Step 13
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
L
1
2
L
L
L
L
1
2
Assembly Instructions
11
Step 14
Step 15
Assembly is complete
Position unit
Carefully lift unit and
position inside your
wardrobe as required.
2 people may be
required for this.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Side
panel
Drawer
ALR2958
Loading...