Argos ZAN33SB-WO-AR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 119.5cm

Depth - 40cm

Height - 77cm

Anderson - 3+3 Sideboard

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 11 - 19/01/15

Important - Please read these instructions fully before starting assembly

609/6465

609/6458

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 42kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (do not use for fitting screws)

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

2

Right Drawer Side

(W509RH)

(330 x 115mm) x 3

Drawer Base (T603)

(333 x 327mm) x 3

5

6

8

13

Left Drawer Side

(W509LH)

(330 x 115mm) x 3

11 12

4

3

7

14

15

9

16

10

Drawer Back

(W537)

(319 x 115mm) x 3

Top (D2266A)

(1193 x 396mm)

Plinth (D2269A)

(1154 x 60mm)

Base (D2268A)

(1154 x 374mm)

Large Shelf (D2261A)

(762 x 368mm)

Left Side (D2182A)

(747 x 375mm)

Right Side (D2183A)

(747 x 375mm)

Door (D2262A)

(524 x 390mm) x 3

Drawer Front (D2263A)

(390 x 157mm) x 3

Divider (D2260A)

(150 x 374mm)

Back (X1181-705)

(1181 x 705mm)

Upright (D2267A)

(671.5 x 374mm)

Small Shelf (D2271A)

(371 x 368mm)

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 4

B

Metal dowel (F901) x 18

C

D

Large locking nut (F900) x 12

E

Small locking nut (F3) x 6

F

G H I

Nail (F51) x 26

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

13mm Screw (F52) x 12

13mm Screw (F63) x 24

Shelf stud (F110) x 8

Knock-in Peg (F171) x 12

L

M

Hinge (F518) x 6

Hinge plate (F523) x 6

40mm Screw (F910) x 1

O

R Runner (F160) x 3

b

L Runner (F161) x 3

O

c

L Runner (F159) x 3

O

a

R Runner (F162) x 3

O

d

N

Handle (F847a ) x 6

a

N

Handle Screw (F847b) x 12

b

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten metal dowels up fully against the panels.

B

10

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

F

11

12

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

11 12

10

F

11 12

F

x 3 x 3

x 3

B

F

11

12

10

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

10

x 3

10

11

B

F

Groove

11

12

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

Assembly Instructions

5

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

14

11 12

10

13

11 12

14

13

G

11 12

Attach the handle

Attach a handle to each drawer front using 2 screws .

10

N a

N b

G

x 3

10

11

12

14

12

14

13

11

G

10

N a

N b

Finished

front edge

A

Assembly Instructions

6

Step 7

Fit runners to the drawers

Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit the runner to the bottom edge of the right drawer side using the same method.

Turn the drawers over

12

O c

11

10

H

O d

Runners must be

pushed up against

the drawer front

H

O c

O d

Prepare the left side

Tap a wooden dowel into the left side .

Screw 3 metal dowels into the left side .

Insert a large locking nut into the left side . .

Fit the runner to the left side .

The 1st screw uses the 2nd hole in from the front of the runner .

The 2nd screw uses the hole that lines up with the other panel hole.

Fit 2 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

Step 8

B

L

I

O a

E

10mm

A

O a

I

Finished front edge

I

1st screw

2nd screw

E

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

A

1

B

E

1

O a

I

O a

I

L

1

11

12

10

x 3

1

A

Assembly Instructions

7

Step 9

Step 10

Prepare the base

Insert 4 large locking nuts into the base

E

I

O b

I

Finished front edge

I

1st screw

2nd screw

L

B

2

L

Prepare the right side

Tap a wooden dowel into the right side .

Screw 3 metal dowels into the right side .

Insert a large locking nut into the right side . .

Fit the runner to the right side .

The 1st screw uses the 2nd hole in from the front of the runner .

The 2nd screw uses the hole that lines up with the other panel hole.

Fit 2 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

A

2

B

E

2

O b

I

O b

I

L

2

E

4

plain chipboard surface

Finished

front edge

E

4

.

Finished

front edge

Finished

front edge

Finished

front edge

A

Assembly Instructions

8

Step 11

Prepare the plinth

Tap 2 wooden dowels into the plinth .

Insert 2 large locking nuts into the plinth

Step 12

Fit the plinth

Push the plinth onto the right side .

Use a screwdriver to tighten the large locking nut fitted to the plinth . .

Step 13

Join the right side and base

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

E

4

2

4

E

plain chipboard surface

A

9

E

.

9

2

E

6

B

E

9

E

4

plain chipboard surface

2

plain chipboard surface

9

2

Assembly Instructions

9

Step 14

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 3 large locking nuts fitted to the base and plinth . .

Step 15

1

E

4

9

Prepare the top

Screw 6 metal dowels into the top .

3

B

3

1

4

9

Finished

front edge

Assembly Instructions

10

Step 16

Turn the drawer

divider over

Prepare the divider

a: Insert 2 large locking

nuts into the divider . .

Note: The 2 holes for the large locking nuts may be drilled in either surface of the divider . .

b: Fit a runner to

this surface of the divider .

Note: Use the finished front edge to identify which runner to fit.

The 1st screw uses the 2nd hole in from the front of the runner.

The 2nd screw uses the hole that lines up with the other panel hole.

c: Turn the divider

over and fit the runner . to the other surface.

a:

b:

c:

5

E

O b

5

I

5

O a

I

Finished front edge

I

1st screw

2nd screw

O b

I

Finished front edge

I

1st screw

2nd screw

5

Finished

front edge

5

I

O b

E

5

Finished

front edge

I

O a

5

Finished

front edge

Assembly Instructions

11

Step 17

Step 18

Fit the divider

Push the divider onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the divider .

Note: The 2 large locking nuts may be on either surface of the divider.

3

5

E

5

E

Finished

front edge

I

O b

I

Finished front edge

I

1st screw

2nd screw

Turn the upright over

O a

I

Finished front edge

I

1st screw

2nd screw

I

O a

L

Prepare the upright

a: Insert 2 large locking

nuts into the upright . .

Fit a runner to this surface of the upright . .

The 1st screw uses the 2nd hole in from the front of the runner.

The 2nd screw uses the hole that lines up with the other panel hole.

b: Turn the upright

over and fit the runner . to the other surface.

Fit 2 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.

a:

b:

6

E

O b

6

I

6

O a

L

6

Finished

front edge

5

3

6

3

Finished

front edge

Assembly Instructions

12

Step 19

Step 20

Fit the top

Push the top onto the side panels and . .

Use a screwdriver to tighten the 2 large locking nuts fitted to the side panels and . .

Secure the upright to the base using screw . .

3

1

2

E

1

2

Fit the upright

Push the upright onto the top .

Use a screwdriver to tighten the 2 large locking nuts fitted to the upright .

3

6

E

6

4

C

6

3

2

4

C

1

Assembly Instructions

13

Step 21

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

Warning: The unit is heavy. Lift with care.

Fit back panel

a: Square up the unit by

making sure that measurement x to x

equals y to y.

b: Place the back

down onto the unit, as shown.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

16

D

y

x

16

b:

D

Assembly Instructions

14

Step 22

Step 23

Fit the shelf

Insert 8 shelf studs at the required height for the large shelf and the small shelf .

Lower the large shelf and small shelf down onto the shelf studs .

J

7

8

Prepare the doors

Push fit 2 hinges into each of the doors .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

H

M

15

M

H

90

M

H

x 3

15

7

8

J

x 4

J

x 4

8

7

Assembly Instructions

15

Step 24

Small piece of

waste wood

Small piece of

waste wood

ONLY drill

these 2 holes

ONLY drill

these 2 holes

DO NOT drill

these holes

DO NOT drill

these holes

15

Drill the handle holes in the door

Important: Please follow these instructions carefully.

Lay the doors down onto a smooth surface.

Important: Check that the holes and hinges are in the same place as the diagrams.

Note: We recommend the use of a small piece of waste wood, placed behind the hole while drilling, to reduce the possibility of any breakout.

Using the pilot hole in the rear face of the door , drill through the holes indicated opposite, using a 2.5mm diameter drill.

Turn the door over and open out the 2.5mm holes that you have just drilled by drilling back through them with a 5mm drill.

These will be the left

door and centre door

This will be

the right door

15

IMPORTANT

You will need to drill the doors to

suit the handles supplied

x 2

x 1

You will need to drill 2 doors as

shown in this diagram

You will need to drill 1 door as

shown in this diagram

Assembly Instructions

16

Step 25

Fit doors and handles

Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinge.

a: Push the hinge

onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

e: Attach a handle

to each door using 2 screws .

M

L

M

L

N a

15

e:

N b

a: b:

c: d:

L

M

L

B

L

M

A

M

L

B

N a

N b

15

Assembly Instructions

17

Step 26

b:

c:

d:

a:

Adjust the doors if needed

a: Before adjusting the

doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.

c: Forward and Back

adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.

d: Sideways

adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.

A

B

C

Note: The diagrams above show the hinges and plates for the 2 outer doors. The hinges and plates for the centre door are adjusted in the same way.

Assembly Instructions

18

Step 27

Fit the drawers

Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.

Side panel

Drawer

Assembly Instructions

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR275219

Step 28

Fit the overbalance protector kit

To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice.

Wall fixings are not supplied as they will need to suit the wall type.

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Assembly is complete

K

Attach the

strap to the unit

Attach the

strap to the wall

Wall fixing

(not supplied)

Washer

Strap

K

Example

Screw

(not supplied)

Washer

Screw

UNIT

MADE IN

BRITAIN

Dimensions

Width - 119.5cm

Depth - 40cm

Height - 77cm

Anderson - 3+3 Sideboard

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 5 - 24/09/12

Important - Please read these instructions fully before starting assembly

609/6465

609/6458

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 42kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not

recommend the

use of power

drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (do not use for fitting screws)

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Left Side (D1524A)

(747 x 375mm)

Divider (D1528A)

(150 x 371mm)

2

Right Side (D1525A)

(747 x 375mm)

Door (D1530A)

(524 x 390mm) x 3

Right Drawer Side

(W509RH)

(330 x 115mm) x 3

Drawer Base (T603)

(333 x 327mm) x 3

Drawer Back

(W563)

(322 x 115mm) x 3

5

6

8

13

Left Drawer Side

(W509LH)

(330 x 115mm) x 3

11 12

4

3

7

14

15

9

16

Plinth (D1537A)

(1159 x 60mm)

Large Shelf (D1535A)

(766 x 368mm)

Top (D1533A)

(1193 x 396mm)

Base (D1534A)

(1159 x 371mm)

Back (X886)

(1178 x 695mm)

Upright (D1536A)

(671.5 x 371mm)

Small Shelf (D1538A)

(371 x 368mm)

Drawer Front (D1531A)

(390 x 157mm) x 3

10

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 4

B

Metal dowel (F901) x 18

C

Nail holder (F149) x 1

D

Large locking nut (F900) x 12

E

Small locking nut (F3) x 6

F

G H I

L

Nail (F51) x 26

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

13mm Screw (F52) x 12

13mm Screw (F63) x 24

13mm Screw (F79) x 1

Shelf stud (F110) x 8

Bracket (F327) x 1

Knock-in Peg (F171) x 12

M

N

Hinge (F518) x 6

Hinge plate (F523) x 6

Q

Handle (F847a ) x 6

a

Q

Handle Screw (F847b) x 12

b

P

R Runner (F160) x 3

b

L Runner (F161) x 3

P

c

L Runner (F159) x 3

P

a

R Runner (F162) x 3

P

d

O

40mm Screw (F910) x 1

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3 x 3

x 3

10

11

B

F

Step 2

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten metal dowels up fully against the panels.

B

10

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: Arrow on locking nut must point towards hole in edge of panel.

Step 3

F

11

12

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

11 12

10

F

11 12

Groove

F

11

12

11

12

10

F

x 3

B

10

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

Assembly Instructions

5

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

14

11 12

10

13

11 12

14

13

K

11 12

Attach the handle

Attach a handle to each drawer front using 2 screws .

10

912

11

14

12

11

K

Q b

Q a

10

x 3

13

Q a

Q b

10

Assembly Instructions

6

Step 7

Fit runners to the drawers

Fit the runner to the bottom edge of the left drawer side , as shown, making sure that it is pushed up against the back of the drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .

Fit the runner to the bottom edge of the right drawer side using the same method.

Turn the drawers over

12

P c

11

10

H

P d

Runners must be

pushed up against

the drawer front

H

P c

P d

Prepare the left side

Tap a wooden dowel into the left side .

Screw 3 metal dowels into the left side .

Insert a large locking nut into the left side . .

Fit the runner to the left side .

The 1st screw uses the 2nd hole in from the front of the runner .

The 2nd screw uses the hole that lines up with the other panel hole.

Fit 2 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

Step 8

A

B

M

I

P a

E

10mm

A

P a

I

Finished front edge

I

1st screw

2nd screw

E

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

A

1

B

E

1

P a

I

P a

I

M

1

11

12

10

x 3

1

Assembly Instructions

7

Step 9

A

Step 10

Prepare the base

Insert 4 large locking nuts into the base

E

H

P b

I

Finished front edge

I

1st screw

2nd screw

M

B

2

M

Prepare the right side

Tap a wooden dowel into the right side .

Screw 3 metal dowels into the right side .

Insert a large locking nut into the right side . .

Fit the runner to the right side .

The 1st screw uses the 2nd hole in from the front of the runner .

The 2nd screw uses the hole that lines up with the other panel hole.

Fit 2 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

A

2

B

E

2

P b

I

P b

I

M

2

E

4

plain chipboard surface

Finished

front edge

E

4

.

A

Assembly Instructions

8

Step 11

Prepare the plinth

Tap 2 wooden dowels into the plinth .

Insert 2 large locking nuts into the plinth

Step 12

Fit the plinth

Push the plinth onto the right side .

Use a screwdriver to tighten the large locking nut fitted to the plinth . .

Step 13

Join the right side and base

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

E

4

2

plain chipboard surface

4

2

4

E

plain chipboard surface

A

9

E

.

9

2

E

6

2

B

E

9

E

plain chipboard surface

9

Assembly Instructions

9

Step 14

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 3 large locking nuts fitted to the base and plinth . .

Step 15

1

E

4

9

Prepare the top

Screw 6 metal dowels into the top .

Fix the bracket , in the middle of the top and flush to the back edge, using screw .

3

B

G

L

3

4

9

1

B

3

G

L