Argos ZAN22SB2-BO-SIAR ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 80cm

Depth - 40cm

Height - 77.5cm

Anderson - 2+2 Sideboard

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Important - Please read these instructions fully before starting assembly

Issue 9 - 28/04/15

289/8533

609/5538

412/7714

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 28kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (do not use for fitting screws)

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left Drawer Side (W509LH)

(330 x 115mm) x 2

Right Drawer Side (W509RH)

(330 x 115mm) x 2

Drawer Base (T603)

(333 x 327mm) x 2

Drawer Back (W537)

(321 x 115mm) x 2

119 10

Left Side (D2182A)

(747 x 375mm)

Top (D2184A)

(796 x 396mm)

Right Side (D2183A)

(747 x 375mm)

Door (D2262A)

(524 x 390mm) x 2

Plinth (D2265A)

(762 x 60mm)

Drawer Front (D2263A)

(390 x 157mm) x 2

Base (D2185A)

(762 x 374mm)

Shelf (D2261A)

(762 x 368mm)

Back (X786-705)

(786 x 705mm)

Divider (D2260A)

(150 x 374mm)

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 4

Metal dowel (F901) x 14

Large locking nut (F900) x 10

Small locking nut (F3) x 4

G H I

Nail (F51) x 21

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

13mm Screw (F52) x 8

13mm Screw (F63) x 16

Shelf stud (F110) x 4

Knock-in Peg (F171) x 8

Handle (F847a ) x 4

Handle Screw (F847b) x 8

Hinge (F518) x 4

Hinge plate (F523) x 4

R Runner (F160) x 2

L Runner (F161) x 2

L Runner (F159) x 2

R Runner (F162) x 2

Strap

Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

x 2 x 2

x 2

Step 2

Prepare the drawer fronts

Screw 2 metal dowels into the holes shown on the back of each drawer front .

Note: Tighten metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and right drawer side .

Note: Arrow on locking nut must point towards hole in edge of panel.

Step 3

Attach the drawer sides to the drawer front

Push the left drawer side . and right drawer side . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

Groove

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

Assembly Instructions

Step 4

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and .

Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

9 10

Attach the handle

Attach a handle to each drawer front using 2 screws .

x 2

J a

J b

J a

J b

+ 14 hidden pages