Page 1
MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 39.5cm
Height - 78cm
Ohio - 6+2 Sideboard
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 28/04/15
Important - Please read these instructions fully before starting assembly
314/7128
392/7544
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 43kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Page 3
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Shelf (D1791A)
(334 x 350mm) x 2
Top (D1811A)
(1200 x 395mm)
Plinth (D1816A)
(1016 x 95mm)
1
Door (D1808A)
(492 x 342mm) x 2
4 5
2
18
19
13
15
17
3
16
14
12
6
Fascia (D1806A)
(755 x 70mm) x 2
7
8 9
Central Drawer
Front (D1817A)
(322 x 162mm) x 4
Back (X921)
(1038 x 669mm)
Left Drawer
Front (D1818A)
(342 x 162mm)
Right Drawer
Front (D1819A)
(342 x 162mm)
10 11
Divider (D1815B)
(645 x 349mm) x 2
Base (D1814B)
(1016 x 350mm)
Left Side (D1812B)
(755 x 357mm)
Right Side (D1813B)
(755 x 357mm)
Large Drawer
Base (T297-347)
(297 x 347mm) x 2
Small Drawer
Base (T266-347)
(266 x 347mm) x 4
Small Drawer
Back (W255-124)
(255 x 124mm) x 4
Left Drawer
Side (W350-124LH)
(350 x 124mm) x 6
Right Drawer
Side (W350-124RH)
(350 x 124mm) x 6
Large Drawer
Back (W286-124)
(286 x 124mm) x 2
Page 4
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 32
C
D
Large locking
nut (F900) x 20
F
H
19mm Screw (F461) x 16
I
Small locking
nut (F3) x 12
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
K
G
Knock-in Peg (F171) x 24
L
N O
Shelf support (F121) x 8
13mm Screw (F63) x 44
E
Nail (F51) x 23
M
Hinge plate
(F523) x 4
Hinge (F522) x 4
Handle (F287) x 8
P
R Runner (F160) x 6
b
L Runner (F161) x 6
P
c
L Runner (F159) x 6
P
a
R Runner (F162) x 6
P
d
J
9mm Screw (F73) x 36
Q
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Plastic Nail (F91) x 5
Wedgefix (F639) x 12
Page 5
9
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 6
x 4x 1x 1
x 6
x 6
B
B
D
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the left drawer front ,
the right drawer front
and the 4 central drawer
fronts .
Note: Tighten metal
dowels up fully against
the panels.
B
10
11
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
8
9
Attach the drawer
sides to the drawer
fronts
Push the left drawer side
. and right drawer side
. onto the back of the
drawer fronts ,
and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
101211
D
8
D
D
D
8
9
D
Note: The left drawer
front has a shallow
identification mark.
10
9
9
10 11 12
B
B
B
10
11
B
B
B
12
12
8
Page 6
G
G
Assembly Instructions
5
Step 4
Fit the drawer bases
a: Slide the large drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the left drawer front
and right drawer front .
b: Slide the small
drawer base down
the grooves in the
drawer sides and
and down into the
groove in the central
drawer fronts .
Step 5
Fit the drawer backs
a: Fit the large drawer
back between the
drawer sides and .
Make sure that the large
drawer base fits into
the groove in the large
drawer back .
Hold the large drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
b: Fit the small drawer
back between the
drawer sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
15
98
10
11
16
98
12
G
G
G
13
8 9
15
13
13
G
8 9
14
8 9
16
14
14
G
8 9
x 2
8
9
15
10
11
12
x 2
8
9
16
x 4
a:
a:
b:
b:
G
G
x 4
G
8
9
15
13
8
9
16
14
Page 7
Assembly Instructions
Step 6
Step 7
Step 8
Attach the handles
Attach a handle to
each drawer front ,
and using 2 screws .
O
H
101211
x 2 x 4
x 6
H
H
O
10
11
H
H
O
12
6
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front , and .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
9
P c
8
10 11 12
K
P d
x 6
K
K
K
K
Runners must be
pushed up against
the drawer front
P d
11
12
10
P c
I
Fit the wedgefixes
Turn all of the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
I
I
I
Page 8
Assembly Instructions
7
Step 9
Step 10
Left fascia - holes
nearest this side
A
A
B
B
B
Prepare the 2 fascias
Check that the holes are
in the same place as the
diagrams, as one will be
the left fascia and one
will be the right fascia.
Screw 3 metal dowels
into each of the 2 fascias
. .
Tap a wooden dowel
into each of the 2 fascias
. .
7
7
B
7
10mm
A
7
B
B
B
A
x 1
x 1
Right fascia - holes
nearest this side
Prepare the left side
Insert 3 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the holes in the
edge of the panel.
C
C
C
4
C
4
C
Page 9
Assembly Instructions
8
Step 11
Step 12
a:
b:
Join the left side to
the left fascia panel
a: Push the left side
down onto the left fascia
panel .
b: Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the left side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
7
C
4
C
Dowel
this end
4
7
7
4
C
B
Left fascia
C
Prepare the right side
Insert 3 large locking
nuts into the right
side .
C
5
C
C
C
5
C
Page 10
Assembly Instructions
9
Step 13
Join the right side to
the right fascia panel
a: Push the right side
down onto the right
fascia panel .
b: Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
C
B
C
7
5
7
5
7
C
5
C
b:
a:
Dowel
this end
5
Right fascia
5
Page 11
A
Assembly Instructions
10
Step 14
b:
a:
Finish preparing the
left side
a: Fit a runner to
the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Screw 3 metal dowels
into the left side .
b: Fit a screw into
the 1st hole in at the top
of the runner .
Insert 2 large locking
nuts into the left side
. .
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
Tap a wooden dowel
into the left side .
P a
4
J
J
K
P a
M
4
B
4
C
4
M
B
B
4
4
C
C
K
M
M
B
A
4
P a
J J
1st
screw
2nd
screw
J
3rd
screw
Finished
front edge
P a
K
Finished
front edge
J
P a
J
J
Page 12
A
Assembly Instructions
11
Step 15
b:
a:
M
Finish preparing the
right side
a: Fit a runner to
the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Screw 3 metal dowels
into the right side .
b: Fit a screw into
the 1st hole in at the top
of the runner .
Insert 2 large locking
nuts into the right
side .
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
Tap a wooden dowel
into the right side .
P b
5
J
J
K
P b
M
5
B
5
C
5
B
B
B
K
C
C
M
M
5
5
Step 16
Prepare the base
Insert 4 large locking
nuts into the base .
C
2
A
5
C
C
C
C
plain chipboard surface
2
Finished
front edge
P b
JJ
1st
screw
2nd
screw
J
3rd
screw
P b
K
J
P b
J
J
Page 13
A
Finished
front edge
Assembly Instructions
12
Step 17
Fit the base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
C
2
5
2
Step 18
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Insert 2 large locking
nuts into the plinth .
6
6
A
C
Step 19
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
C
6
5
6
5
2
plain chipboard surface
C
C
A
plain chipboard surface
6
plain chipboard surface
6
5
Page 14
Assembly Instructions
13
Step 20
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the base and plinth
. .
4
C
2
6
Prepare the top
Screw 8 metal dowels
into the top .
B
Step 22
Step 21
1
4
2
6
4
6
B
B
B
B
B
B
B
B
1
Finished
front edge
Fit the 5 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. and 1 into the centre
of the bottom edge of
the plinth .
L
4
5
L
L
L
L
L
6
5
Page 15
Finished
front edge
Assembly Instructions
14
Step 23
Prepare the left
divider
a: Fit a runner to
the divider .
The 1st screw uses
the 1sthole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Tap 2 wooden dowels
into the divider .
Turn the divider over
c: Fit 4 runners to
the divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
d: Fit a screw into
the 2nd hole in at the top
of the runner .
Insert 2 large locking
nuts into the divider
. .
Finished
front edge
C
C
K
K
K
K
Finished
front edge
Finished
front edge
K
P b
3
J
J
K
P b
3
3
a:
b:
Turn the divider over
d:
3
P a
3
J
J
K
P a
C
3
3
A
A
A
3
P b
JJ
1st
screw
2nd
screw
J
3rd
screw
P b
K
J
P b
J
J
P a
J J
1st
screw
2nd
screw
J
3rd
screw
Finished
front edge
P a
K
Finished
front edge
J
P a
J
J
J
P a
J
J
J
P a
J
J
J
P a
J
J
c:
Page 16
Finished
front edge
Finished
front edge
Assembly Instructions
15
Step 24
Prepare the right
divider
a: Fit 4 runners to
the divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Tap 2 wooden dowels
into the divider .
Turn the divider over
c: Fit a runner to
the divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
d: Fit a screw into
the 2nd hole in at the top
of the runner .
Insert 2 large locking
nuts into the divider
. .
C
C
K
Finished
front edge
Finished
front edge
K
K
K
K
P b
3
J
J
K
P b
3
3
a:
b:
Turn the divider over
c:
d:
3
3
P a
3
J
J
K
P a
P b
K
Finished
front edge
C
3
A
3
P a
J J
1st
screw
2nd
screw
J
3rd
screw
Finished
front edge
P a
K
Finished
front edge
J
P b
J
J
J
P b
J
J
J
P b
J
J
J
P b
J
J
J
P a
J
J
P b
JJ
1st
screw
2nd
screw
J
3rd
screw
Finished
front edge
A
A
Page 17
Assembly Instructions
Step 25
Fit the dividers
Carefully stand the
unit up for this step.
Push the 2 dividers
down onto the base .
3
3
2
3
2
Finished
front edge
Step 26
Fit the top
Push the top down
onto the assembly.
Use a screwdriver to
tighten the 8 large
locking nuts fitted to
the left side , the right
side and the 2
dividers .
1
C
4
5
3
Warning: The
unit is heavy.
Lift with care.
1
4
5
3
3
Finished
front edge
16
Page 18
Assembly Instructions
17
Step 27
Fit the back
Lay the unit back
down for this step.
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about 150mm
apart.
Stand the unit up for
the next step.
19
E
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
19
19
b:
E
y
y
x
Step 28
Warning: The
unit is heavy.
Lift with care.
1
x
Fit the overbalance
protector
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the
overbalance protector kit
. fitted to the unit or, an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Q
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
WasherWasher
Screw
Q
Q
Example
Screw
(not supplied)
Page 19
Assembly Instructions
Step 29
18
Step 30
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Drawer
Fit the shelf studs
Insert the shelf studs .
You have a choice of 3
height positions.
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
F
F
Note: The left drawer front
has a small identification hole.
Please refer back to Step 1.
F
x 4
F
x 4
Page 20
Assembly Instructions
19
Step 31
Fit the shelves
Lower the 2 shelves
down onto the shelf
studs .
17
F
17
17
Step 32
Prepare the 2 doors
Push fit 2 hinges into
each of the 2 doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
K
N
18
90
N
N
K
K
18
x 2
N
K
K
Page 21
Assembly Instructions
Step 33
20
Small piece of
waste wood
Small piece of
waste wood
ONLY drill these
2 holes in 1 door
ONLY drill these
2 holes in 1 door
Drill 2 handle holes in
each of the doors
Important: Please follow
these instructions
carefully.
Lay the 2 doors
down onto a smooth
surface.
Check that the hinges
and holes are in the
same place as the
diagrams.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
18
This will be the
left hand door
This will be the
right hand door
IMPORTANT
Carefully choose which 2 holes
you need to drill in each door
18
18
Page 22
Assembly Instructions
21
Step 34
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
N
N
N
M
M
M
N
M
O
H
18
18
a: b:
c: d:
M
N
M
M
B
M
N
N
N
A
N
M
B
e:
H
H
O
18
18
O
Page 23
Assembly Instructions
Step 35
22
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Page 24
Assembly Instructions
23
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 36
Warning: The
unit is heavy.
Lift with care.
Assembly is complete
ALR3081
Loading...