MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 33cm
Height - 45cm
Winchester - Low Hall Cubby Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 15/05/15
Important - Please read these instructions fully before starting assembly
414/9431
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 19kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
2 3
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
4
Divider (DF2973)
(305 x 303mm) x 2
Shelf (DF2968)
(298 x 301mm) x 3
Left End (DF2971)
(425 x 307mm)
Right End (DF2972)
(425 x 307mm)
Top (DF3377)
(996 x 327mm)
Base (DF2966)
(926 x 306mm)
Rail (DF2791)
(926 x 90mm) x 2
Side Plinth (DF2941)
(307 x 91mm) x 2
Back (X952-346)
(952 x 346mm)
Front Plinth (DF2792)
(988 x 92mm)
5 6
7 8
9
10
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
E F
G H
C
Large locking
nut (F900) x 14
Metal dowel (F901) x 14
Plastic Nail (F91) x 5
Nail (F51) x 20
Wooden dowel (F22) x 16
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
D
40mm Screw (F910) x 6
25mm Screw (F50) x 6
Shelf stud (F110) x 12
C
C
Finished
front edge
C
C
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the left end
Screw 4 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the left end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
1
B
1
A
10mm
C
B
C
1
A
A
A
A
B
B
A
1
Finished
front edge
B
B
A
A
A
A
Prepare the right end
Screw 4 metal dowels
into the right end .
Insert 2 large locking
nuts into the right end
. .
Tap 2 wooden dowels
into the right end .
A
2
B
2
C
2
2
Finished
front edge
Finished
front edge
D
D
Assembly Instructions
5
Step 3
Step 4
Step 5
C
Prepare the 2 dividers
Tap a wooden dowel
into each of the 2
dividers .
C
5
Finished
front edge
x 2
x 2
C
B
B
C
Prepare the 2 rails
Insert 2 large locking
nuts into each of the
rails .
Tap 2 wooden dowels
into each of the rails .
7
B
7
C
5
Finished
front edge
5
7
Finished
front edge
7
Fit the 2 dividers to 1
of the rails
Attach the 2 dividers
to a rail using screws
. .
D
5
4
5
7
7
Assembly Instructions
6
Step 6
Step 7
7
Fit the right end
Push the right end
onto the rail .
Use a screwdriver to
tighten the large locking
nut fitted to the rail
. .
Note: Turn the large
locking nut as far as it
will go - more than 1/2 a
turn.
2
7
7
B
A
B
2
7
B
Finished
front edge
C
C
Step 8
Finished
front edge
Prepare the base
Insert 4 large locking
nuts into the base .
Tap 4 wooden dowels
into the base .
4
B
4
C
B
B
B
B
C
C
4
4
Fit the base to the
right end
Push the base onto
the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the base .
4
4
2
B
2
Assembly Instructions
7
Step 9
Step 10
7
Fit the 2 dividers
Attach the 2 dividers
to the base using
screws .
D
5
4
4
D
D
D
D
7
2
5
5
Fit the other rail
Push the rail onto the
right end .
Use a screwdriver to
tighten the large locking
nut fitted to the rail
. .
7
7
2
B
7
2
Step 11
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and the 2
rails .
4
7
1
B
7
4
7
1
7
Assembly Instructions
8
Step 12
Prepare the top
Screw 4 metal dowels
into the top .
Step 13
A
3
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and right
end .
3
1
2
B
Note: To make it easier to fit the top and the plinths,
place 4 polystyrene blocks from the packaging
underneath the side panels to raise the assembly.
A
A
A
A
3
3
1
2
Finished
top edge
Finished
top edge
Finished
top edge
C
Finished
top edge
Assembly Instructions
Step 14
9
Prepare a side plinth
Insert a large locking
nut into 1 of the side
plinths .
Tap a wooden dowel
into the side plinth .
9
B
9
C
Step 15
Step 16
Prepare the front
plinth
Screw 2 metal dowels
into the front plinth .
Step 17
A
8
Prepare the other side
plinth
Insert a large locking
nut into the side plinth
. .
Tap a wooden dowel
into the side plinth .
9
B
9
C
Fit the plinths together
Push the 2 side plinths
onto the front plinth .
Use a screwdriver to
tighten the large locking
nuts fitted to the side
plinths .
9
8
B
9
C
B
B
9
9
A
A
8
8
9
9
Fit the plinths
Position the 3 plinths
onto the assembly, as
shown.
Secure the 2 side plinths
. through the left end
. . and right end
using screws .
Use the 2 mark holes on
the side plinths to line
them up with the holes in
the ends.
Assembly Instructions
10
Step 18
Step 19
9
1 2
E
Secure the front plinth
Secure the front plinth
to the bottom rail
using 2 screws .
8
7
E
E
E
E
E
9
1
2
9
E
E
8
7
yy
yy
xx
xx
Assembly Instructions
Step 20
b:
G
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back , as shown.
Note: Nails should be
spaced about 150mm
apart.
10
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
Step 21
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Tap a plastic nail into
the middle of the bottom
rail .
DO NOT fit the
plastinails to the front
plinth or side plinths.
Carefully stand the
unit up for the next
step.
F
1
2
7
Warning: The
unit is heavy.
Lift with care.
11
10
F
F
F
F
F
1
2
F
7
Assembly Instructions
12
Step 22
Step 23
Fit the shelves
Lower the 3 shelves
down onto the shelf
studs .
Fit the shelf studs
For each of the 3
shelves , insert 4 shelf
studs .
H
x 4
H
x 4
H
x 4
H
6
H
6
6
6
6
Assembly Instructions
13
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 24
Assembly is complete
ALR3167
Loading...