Page 1
Wiltshire - Chest of 5 Drawers
Assembly Instructions
- Please keep for future reference
2307189
2457235
2584902
Dimensions
Width - 89cm
Depth - 42.5cm
Height- 110.1cm
Important
If you need help or have damaged or missing parts, call the
14-3E-219_01
– Please read these instructions fully before starting assembly
Customer Helpline:
03456 400 800
Issue 1 - 14/06/06
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (- in the same
room)as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set
on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten bolts.
• Regularly check and ensure
that all bolts and fittings are
tightened properly.
1
Page 3
If you have damaged or missing commponents,
Components - Panels
call the
Please check you have all the panels listed below
Customer Helpline:
3
Top panel x 1 (89 x 42.5cm)
Bottom front support x 1
4
(75 x 7.1cm)
03456 400 800
Right side panel x 1
1
(39.5 x 107.8cm)
6 Back panel x 1
(38.5 x 99.7cm)
Left side panel x 1
2
(39.5 x 107.8cm)
7
Right hinge frame x 1
(5.3 x 107.8cm)
8
Left hinge frame x 1
(5.3 x 107.8cm)
Bottom back support x 1
5
(75 x 7.1cm)
Bottom plinth x 1
9
(74.9 x 2cm)
10
Large drawer front x 5
(74.3 x 19cm)
Right drawer side x 5
11
(35 x 13cm)
Large drawer base x 5
14
(71 x 33.9cm)
12
15
Left drawer side x 5
(35 x 13cm)
Handle x 10
(10.5 x 1.9cm)
Large drawer back x 5
13
(70.6 x 13cm)
2
Page 4
Components - Fittings
Please check you have all the fittings listed below
Note:
The quantities below are the correct amount to complete the assembly. In some cases more fittings may
be supplied than are required.
A
Feet x 4
D
Nail x 30
G
Large locking nut x 15
K
20mm Screw x 20
N
Runner right B x 5
B C
8/30mm Wooden dowel x 20
E F
Screw x 25
H
Small locking nut x 10
L
Runner left A x 5
O
Underlay x 2
6/30mm Wooden dowel x 20
9mm Screw x 20
J
Plastic dowel x 20
M
Runner left B x 5
P
Drawer base support x 10
R
Runner right A x 5
2
U
10mm Screw x 10
Tools required
X
Wall strap x 1
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
S
30mm Screw x 20
Y
13mm Screw x 1
Ruler - Use this ruler to help correctly identify the screws
2
T
Reinforcing metal strap x 5
Z
4
12mm Screw x 10
Hammer
Ruler/tape
measure
The screws length is measured from the head to the point (30mm screw shown)
3
Page 5
Assembly Instructions
Step 1
Attaching runners
a: Position left runners
L
and right runners A
A
R
on to the drilled holes
of the left and right side
F
2
and
and .
2
A
from
A
E
2
panels and .
Fix through holes shown
using screws .
b: Attaching feet
Position plastic feet
to the left and right side
panels
below and fix them using
the hammer.
1
1
Step 2
Preparation for the
attaching of bottom
supports
Insert screws into
the drilled holes of the
left and right side
panels
1
b:
a:
F
L
2
F
A
F
F
L
E
E
2
1
F
1
R
R
E
Step 3
Attaching the bottom
supports
Insert wooden dowels
B
into the bottom front
and back supports
5
and and place on left
and right side panels
2
, . Align correctly and
insert large locking
G
nuts into the bottom
front and back supports
4
and and turn them
clockwise to lock.
5
4
1
G
2
B
B
1
B
4
G
G
5
B
4
Page 6
Assembly Instructions
Step 4
Frame assembly
Insert screws in to the
frames , , .
7 8
E
9
E
9
7
E
E
E
8
E
E
E
Step 5
Insert wooden dowels
as shown, align correctly
and connect the frames
7 8
, and as shown
on the picture.
9
B
B
E
7
B
B
9
B
8
B
5
Page 7
Assembly Instructions
Step 6
Attaching the frame
Insert wooden dowels
B
into the edge of the
left and right side panels
2
1
, .
Align correctly and insert
large locking nuts into
left and right side panels
2
1
, and place the
frame and turn locking
nuts clockwise to lock.
G
Step 7
Attaching top panel
Insert screws into the
drilled holes of the top
panel .
Insert wooden dowels
into the top edges as
B
shown, align correctly and
insert large locking nuts
G
into left and right side
panels and , place
the top panel and turn
locking nuts clockwise to
lock.
3
1
E
2
3
2
G
1
B
B
B
5
8
4
9
7
B
G
G
E
E
3
3
B
B
1
B
2
5
G
G
4
6
Page 8
Assembly Instructions
Step 8
Attaching back panel
Position back panel
in position on the back of
bedside chest. Position
D
nails 5 mm in from
side edge of the back
panel with distance
100 mm between each
other. Fix them using the
hammer.
6
6
Step 9
Drawer assembly
a: Insert screws into
drawer front .
E
10
a:
E
Note: You must ensure
the chest is square
before attaching
the back panel.
6
D
10
b:
C
b: Insert wooden dowels
into left and right
C
12
drawer sides , .
c: Insert plastic dowels
J
into left drawer
12
side and drawer back
13
and fix it together
using the hammer.
d: Insert plastic dowels
J
into right drawer
11
side and drawer back
13
and fix it together
using the hammer.
e: Slide large or small
drawer base into the
grooves.
11
14
c:
13
e:
12
12
11
J
J
J
14
12
d:
11
J
13
12
10
f:
f: Place large or small
drawer front onto
sides.
continued on next page
7
10
11
13
11
13
14
12
Page 9
Assembly Instructions
Step 9 - continued
g: Align correctly and
insert small locking nuts
H
into left and right
12
12
11
M
N
TUT
2
drawer sides , and
turn them clockwise to
lock.
h: Position left and right
runners B , on
to left and right drawer
sides , , fix using
screws .
i: Large drawers only:
Position the reinforcing
metal strap onto the
large drawers as shown.
Fix using supplied screws
.
11
K
2
g:
U
i:
2
13
11
14
H
T
12
10
h:
K
2
K
K
N
M
K
j: Large drawers only:
Position 2 drawer base
supports onto the large
drawers as shown. Fix
using supplied screw.
k: All drawers:
Attach handles
to drawer fronts
using screws .
Repeat assembly for
the remaining drawers.
P
15
S
k:
S S
15
U
j:
2
P
S
P
15
8
Page 10
Assembly Instructions
Step 10
Fixing to wall
It is recomended that the
chest is fixed to a wall.
Poke wall strap
through the hole in the
back panel and fix it to top
panel underneath using
screw and underlay .
Mark fixing hole onto wall.
Drill a hole and insert a
suitable wall plug. Fix wall
strap using a screw
suitable for your wall.
With help, move chest
into position.
Y
X
Warning:
Before drilling,
check wall for
hidden pipes and
cables.
X
O
Note: Wall fixings are not
supplied with this unit.
The correct type of fixing must
X
be used for your wall, seek
professional advice if in doubt.
X
Warning:
The chest
is heavy.
Lift with care.
Step 11
Inserting drawers
Insert the drawers
moving up and down as
shown and ensure that
wheels fit onto left and
R
right runners , .
L
X
O
Y
R
L
Check the gaps
between the drawers
and if they line up,
assembly is complete.
9
Page 11
Assembly Instructions
Step 12
Drawer runner adjustment
To move drawers up or
down: loosen screws as
shown and move runners
L
, up or down as
R
required.
Retighten screws and fix
the runners , using
screws 4 .
R
Z
F
F
L
a:
L
F
Assembly is complete.
b:
F
L
c:
F
L
F
d:
Z
4
L
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Home Retail Group Plc, 489 - 499 Avebury Boulevard, Milton Keynes, MK9 2NW
10
Loading...