Washington - 2 Door 1 Drawer
DR82537
Assembly Instructions - Please keep for future reference
411/3883
414/9015
Dimensions
Width - 90.2cm
Depth - 55.3cm
Height - 193.4cm
411/3883 SMOKEY OAK
414/9015 WARM OAK
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the
Argos 03456 400 800
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Customer Helpline:
Issue 1 - 19/06/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
power drill is set on a low torque
setting.
Warning: Only use a manual
screwdriver to attach the hinges.
• Dispose of all packaging
carefully and responsibly.
Glue safety - Take care when using glue, please follow the advice below•
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
•To reduce the
likelihood of
damaging your
product please
ensure that your
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
•
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
If you have damaged or missing components,
Components - Panels
call the Customer Helpline:
Please check you have all the panels listed below
03456 400 800
Left side
1
(55.1 x 190cm)
P8320
Top
5
7
(90.2 x 55.3cm)
P8152
Horizontal
(83.2 x 53.3cm)
P1871
ID-hole
Right side
2
(55.1 x 190cm)
P8319
back
Plinth
6
(83.2 x 15.6cm)
P4673
Bottom
8
(83.2 x.55cm)
P8153
Left door
3
(41.2 x 157.5cm)
P3709
Foldy back
9
(89.4x161.6cm)
BO2574
Right door
4
(41.2 x 157.5cm)
P3708
Plinth
10
13
(83.2 x 9.2cm)
P7052
Left drawer side
(35 x 14cm)
LA1614
Drawer bottom
11
(79.3 x 34.2cm)
BO2573
Drawer back
14
(78.3 x 14cm)
LA1651
Drawer front
12
(82.6 x 18.9cm)
P4118
Right drawer side
15
(35 x 14cm)
LA1615
2
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
FK1011
A
Locking screw x 14 (5x24mm)
FK1301
D
Fixing screw drawer x 4 (6.3x10mm)
FK1007
Confirmat screw x 4 (7x70mm)
FK10561
Locking screw x 4 (5x11mm)
FK1410
Wood dowel x 4 (5x30mm)
FK1801
P
FK1010
12mm
Locking nut x 2 (12x10mm)
FK1309
E
Screw x 14 (4x12.5mm)
FK1985
Screw x 8 (4x25mm)
FK1051
KJ
Expando housing x 4 (20x12mm)
FK1235
NM
L-Bracket x 1
FK1223
Q
FK1012
CB
15mm
Large locking nut x 12 (15x12mm)
FK1311
F
Screw x 14 (3x15mm)
FK1400
IHG
Screw x 5 (4x15mm)
FK1515
L
Nail x 40
GR1855
O
Drawer handle x 4
PM1831
R
Double plug, Nylon x 2
S
Plug, Nylon x 6
V
Peg, brown x 2
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Piercer
(small)
7mm Suitable drill bit
(for use with wall plug)
FK1800
FK1234
Hanger rail support x 2
T
Drawer base support x 6
Support pin x 2
Drill
(for use with wall plug)
FK1250
FK1203
Hanger rail x 1 (82.5cm)
U
Corner connector, white x 2
FK1415
XW
Nail holder x 1
Small
hammer
0102030405060708090 100 110 120 130 140 150
0123456
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
FK1248
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
110 115 120 125 130 135 140 145 150 155 160 165 170
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
FK12791
Y
Hinge back x 6
PM1515 LB
D
AB
Runner left part B x 1
ZF99936
AE
Wall plug (6mm) & parkerscrew x 1
Hinge door x 6
AC
E
Runner right part A x 1
AF
Allen key x 1 (3mm)
FK12781
PM1515 RA
FK1004
AAZ
Runner left part A x 1
F
AD
Runner right part B x 1
IHG
AG
Glue x 1
PM1515 LA
PM1515 RB
FA1510
4
Assembly Instructions
Step 1
a:
a: Press the Nylon plug S
firmly into left side 1.
Screw 11mm locking
screw J into left side 1.
Note: Insert 11mm locking
screw J as far as shown.
Do not over tighten.
Press the double nylon plug
P firmly into left side 1.
Screw hinge back Y onto
left side 1.
P
Y
Finished
front edge
Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.
J
J
Y
1
S
Y
S
S
Y
b: Attach hanger rail
support Q using
screw E left side 1.
Attaching runners
c: Fix runner left part A a
on left side 1 as shown
usesing fixing screw
drawer D into left side 1.
Note: look carreful for the
right postion.
b:
c:
Finished
front edge
P
E
Q
1
S
1
A
A
AA
J
A
A
A
Insert 15mm screw F
as shown into left side 1
to fix runner left part A a.
Screw 24mm locking
screw A into left side 1.
Note: Insert 24mm locking
screw A as far as shown.
Do not over tighten.
5
Finished
front edge
F F
D D
AA
A
F
A
Assembly Instructions
Step 2
a: Press the Nylon plug S
firmly into right side 2.
Screw 11mm locking
screw J into right side 2.
Note: Insert 11mm locking
screw J as far as shown.
Do not over tighten.
Press the double nylon plug
P firmly into right side 2.
Screw hinge back Y onto
right side 2.
b: Attach hanger rail
support Q using
screw E right side 2.
a:
b:
P
Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.
Y
J
J
2
P
E
Q
S
Y
S
J
Finished
front edge
Y
S
S
ID-hole
Finished
front edge
Y
Attaching runners
c: Fix runner right part A c
on right side 2 as shown
usesing fixing screw
drawer D into right side 2.
Note: look carreful for the
right postion.
Insert 15mm screw F
as shown intoright side 2
to fix runner right part A c.
Screw 24mm locking
screw A into right side 2.
2
c:
2
A
A
A
F F F
D D
Finished
front edge
A
AC
E
A
A
ID-hole
Note: Insert 24mm locking
screw A as far as shown.
Do not over tighten.
AC
E
A
6
Assembly Instructions
Step 3
Insert Support pin W into
top 5. Let the flat side of
support pin W face the
same side as the finished
front edge of top 4.
5
W
W
Do not overtighten.
Step 4
Insert expando housing K
into Plinth back 6.
Step 5
Insert large locking nuts C
into horizontal 7.
W
Finished
front edge
K
K
6
K
K
Finished
top edge
C
C
K
C
Make sure the ‘arrow’ on
large locking nuts C
points towards the hole in
the edge of horizontal 7.
Step 6
Insert large locking nuts C
into bottom 8.
Make sure the ‘arrow’ on
large locking nuts C
points towards the hole in
the edge of bottom 8.
C
C
C
C
C
C
7
C
Finished
front edge
C
C
C
8
C
Finished
front edge
7
Assembly Instructions
Step 7
Put drop of glue g into
the 4 holes of plinth 0.
Insert wood dowel M into
the 4 holes of plinth 0.
Step 8
Attaching panels
Put drop of glue g into
the2 holes of left side 1
and the 2 holes of right side
2.
Position left side 1 and
right side 2 onto
horizontal 7, bottom 8
and plinth 0.
M
M
AG
Finished
front edge
AG
10
1
7
2
10
I
AG
Finished
front edge
M
M
AG
M
I
AG
8
Use a screwdriver to turn
locking nuts C clockwise
to lock.
Step 9
Attaching panels
Attach top 5 with 4x
confirmat screw G onto
left side 1 and right side
2. Use allen key f.
Position plinth back 6
onto left side 1 and right
side 2.
Use a screwdriver to turn
Expando housing K
clockwise to lock.
Mount corner connector U
with 2 screws F on plint
0 and bottom 8.
AF
G
G
Finished
front edge
C
G
5
G
6
2
Finished
top edge
1
7
U
U
10
8
Finished
front edge
I
U
K
I
8
Assembly Instructions
Step 10
Fitting back panel
Attach foldy back 9 to the
back with the coloured
surface facing the inside
using nails L.
Use nail holder X to hold
the nails L vertical and at
correct distance as you
secure the foldy back 9.
Nails L should be spaced
about 150mm apart.
Important:
Furniture MUST
be ‘square’ when
back is attached.
L
L
L
L
L
2
L
L
9
L
L
X
L
L
7
8
L
Step 11
Fitting hinges to doors
Fix three hinge door
left door
door
3 and right
4 using screws E.
Z to
X
Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.
Z
Z
4
Z
E
E
3
Z
Z
Z
Z
9
Assembly Instructions
Step 12
Hanging doors
a: With help, slot hinge
door Z onto hinge
back Y.
b: Tighten hinge door
screw to lock hinges in
postion.
Repeat a and b for other
door.
For adjusting the hinges
see ‘adjustment’ on page
‘hinge adjustment’.
c: Fix drawer handle O
onto left door 3 and right
door 4 using screw H.
a:
b:
Y
Q
Z
Y
Q
Q
2
6
Z
R
4
d: Inserting hanger rail
Insert hanger rail R into
hanger rail support Q.
9
1
3
O
7
8
H
H
H
H
O
10
Assembly Instructions
Step 13
Preparing drawer
Insert locking nuts B into
left drawer side # and
right drawer side %.
Make sure the ‘arrow’ on
locking nuts B points
towards the hole in the
edge of left drawer side #
and right drawer side %.
Put drop of glue g into the
3 holes of left drawer side
# and right drawer side %.
Attach left drawer side #
and right drawer side %
onto drawer back $.
Insert drawer bottom !.
Step 14
AG
13
AG
15
14
11
B
B
B
AG
A
Screw 24mm locking
screw A into drawer front
@.
Note: Insert 24mm locking
screw A as far as shown.
Do not over tighten.
Step 15
Position drawer front @
onto drawer.
Use a screwdriver to turn
locking nuts B clockwise
to lock.
Note: look carefully to the
positions of drawer front @.
Fix drawer handles O onto
drawer front @ using
screw H.
12
A
O
O
15
12
H
H
H
11
H
14
A
13
11
B
Assembly Instructions
Step 16
a:
Turn over drawer.
a: Fix runner left part B b
on left drawer side # as
shown using screw F.
Fix runner right part B d
on right drawer side % as
shown using screw F.
AB
11
AD
F
15
14
b: Fix runner left part B b
and runner right part B d
using screw F.
Slide drawer base support
T in corner as shown and
fix them, using the attached
screw.
b:
13
F
T
T
F
T
F
F
AB
13
11
T
5
T
14
F
AD
T
F
F
15
T
Step 17
Inserting drawers
as shown.
For adjusting the drawers
see ‘adjustment’ on page
‘drawer adjustment’.
4
3
1
12
12
Assembly Instructions
Step 18
a: Position L-bracket N on
top 5 as shown, fix using
screw I.
Note: there is no pre-drilled
hole for screw I.
Use wall plug & parker
screw e to fix on the wall,
please see page ‘Wall
Mounting & Fixings’ for
more information.
b: Before adjusting the
doors, use a spirit level to
check if the base of this
unit is level front-to-back
and side-to-side in the
three positions shown.
a:
AE
I
N
I
N
5
AE
4
Use peg V to square
your furniture. Knock peg
V in, as far as you require,
under the end of the side of
the forniture. Then snap off
flush with the side.
Assembly is complete.
3
1
12
b:
V
V
V
!
V
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos 03456 400 800
13
A Guide to - Hinge adjustment
Adjustment
Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Once doors are aligned,
re-tighten.
b: To move doors in
or out: loosen screw
shown and move doors
to suit.
a:
Re-tighten screws.
c: To move doors left
or right: loosen screw
shown and move doors
to suit.
Re-tighten screws.
b:
c:
14
A Guide to - Drawer adjustment
Adjustment
Note: Each drawer can be
adjust for approximately
1mm up or down on each
site of the drawer.
Remove drawer, adjust the
wheel from runner left
part A and runner right part
A as shown.
Insert drawer.
Repeat above steps until
the desired result is
achieved.
R
Runner left part A x 2
+1 mm
T
Runner right part A x 2
-1 mm
0
15
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
plasterboard. The hamemr fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
16
Loading...