Argos Walton - Corner Desk ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 89.5cm
Height - 74cm
Walton - Corner Desk
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/10/13
Important - Please read these instructions fully before starting assembly
162/8405
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 29kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Return Leg (D1417A)
(718 x 231mm)
Left Side (D1414A)
(718 x 570mm)
Right Side (D1415A)
(718 x 570mm)
Large Modesty (D1418A)
(944.5 x 239mm)
Small Modesty (D1419A)
(639.5 x 239mm)
Top (D1413A)
(1199 x 894mm)
2
4
6 7
3
Leg (D1416A)
(718 x 214mm)
5
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 4
B
Metal dowel (F901) x 8
C
D E
Large locking nut (F900) x 8
F
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill (do not use for fitting screws)
50mm Screw (F49) x 8
45mm Screw (F65) x 2
Allen Key (F36) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the top
Screw 8 metal dowels into the top .
Note: Tighten the metal dowels up fully against the panels.
B
B
B
B
B
B
B
B
B
B
1
1
Step 3
Prepare the return leg
Insert 2 large locking nuts into the return leg .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
C
C
C
C
Finished
front edge
C
Prepare the leg
Insert 2 large locking nuts into the leg .
C
4
5
4
C
5
Assembly Instructions
5
Fit the return leg
Push the return leg onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the return leg .
Step 4
Step 5
1
C
B
5
1
Finished
front edge
4
Fit the leg to the top
Push the leg onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the leg .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
5
1
C
5
C
4
1
C
4
Assembly Instructions
6
Step 6
Secure the leg to the return leg
Secure the return leg to the leg using 2 screws .
Note: Make sure that the leg is straight and in line with the return leg.
1
4
5
E
E
4
5
E
Step 7
Fit the small modesty
Push the small modesty . against the leg and secure it using 2 screws and the allen key .
5
7
D
F
D
7
5
D
F
Assembly Instructions
7
Step 8
Fit the large modesty
Push the large modesty . against the return leg . and secure it using 2 screws and the allen key .
6
4
D
F
6
4
D
F
D
A
A
Step 9
C
10mm
A
Prepare the left side
Tap 2 wooden dowels into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into the left side .
Step 10
C
A
2
C
2
2
Finished
front edge
A
A
C
C
Prepare the right side
Tap 2 wooden dowels into the right side .
Insert 2 large locking nuts into the right side .
3
A
3
C
3
Finished
front edge
Assembly Instructions
8
Step 11
Fit the right side
Push the right side onto the top .
Secure the right side to the large modesty using 2 screws and allen key .
D
D
F
3
1
6
3
1
3
6
D
F
Secure the right side
Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .
Step 12
C
3
3
Assembly Instructions
9
Step 13
Step 14
D
D
F
Fit the left side
Push the left side onto the top .
Secure the left side to the small modesty using 2 screws and allen key .
2
1
2
7
D
F
1
2
7
2
Secure the left side
Use a screwdriver to tighten the 2 large locking nuts fitted to the left side .
C
2
Assembly Instructions
10
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 15
Turn the unit over
2 people are needed here
Carefully turn the unit over onto its feet and place it into position.
Assembly is complete
ALR2915
Loading...