MADE IN
BRITAIN
Dimensions
Width - 39.5cm
Depth - 59.5cm
Height - 74cm
Walton - 2 Drawer Filer
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/10/13
Important - Please read these instructions fully before starting assembly
166/2629
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2
Left Drawer Side (W528LH)
(386 x 150mm) x 2
Right Drawer Side (W528RH)
(386 x 150mm) x 2
Drawer Back (W528)
(309 x 150mm) x 2
3
4 6
9 10
7 8
File Bar (FBAR336)
(336mm) x 4
5
Left Side (D2372A)
(718 x 570mm)
Right Side (D2373A)
(718 x 570mm)
Top (D2371A)
(394 x 593mm)
File Front (D2376A)
(387 x 338mm) x 2
Back (X708-385)
(708 x 385mm)
Base (D2374A)
(359 x 567mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 12
C
D E F
K
G
Large locking
nut (F900) x 8
13mm Screw (F63) x 8
Nail (F51) x 15
Small locking
nut (F3) x 4
13mm Screw (F52) x 8
Knock-in Peg (F171) x 8
JJ
CL Runner
(F904) x 2
DL Runner
(F906) x 2
a
J
b
J
c
J
d
DR Runner
(F905) x 2
CR Runner
(F903) x 2
19mm Screw (F461) x 4
I
I
Handle (FWALTON) x 2
H
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2 x 2
x 2
B
Step 2
Prepare the 2 file
fronts
Screw 2 metal dowels
into the holes shown on
the back of the file front
. .
Note: Tighten metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
9
10
Fit the file bars
Push 2 file bars into
each pair of drawer
sides and .
D
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
D
10
9
B
B
7
D
10
9
9 10
5
5
5
Assembly Instructions
5
Step 4
Step 5
x 2
Attach the drawer
sides to the file front
Push the left drawer side
. and right drawer side
. onto the back of the
file front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
7
D
9
10
B
B
D
D
10
7
9
K
K
10
9
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
9 10
8
K
9 10
K
K
x 2
8
Assembly Instructions
6
Step 6
Fit the runners
Position the runner ,
onto the left drawer side
. as shown, making
sure that the front of the
runner is pushed up
against the back of the
file front .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit runner to the
right drawer side
using the same method.
Attach the handle
Attach a handle to
each of the the 2 file
fronts using 2 screws
. .
Step 7
7
I
I
H
x 2
x 2
c
J d
E
9
10
7
J d
J c
Runners must be
pushed up against
the file front
E
E
E
E
10
9
J
7
7
H
I
Turn the drawer assemblies over
A
A
Assembly Instructions
7
Step 8
I b
F
F
Fit runners to the left
side
Fit the 2 runners
marked ‘CL’ to the left
side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
Fit the 2nd screw into
the corresponding hole
in the left side .
Finished
front edge
B
C
10mm
A
1
Finished
front edge
B
C
C
1
J a
F
1
J a
F
1
Step 9
Finish preparing the
left side
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 2 metal dowels
into the left side .
Note: Tighten metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
B
1
C
1
A
1
J a
CL
F
F
F
F
J a
CL
CL
J a
CL
F
F
CL
CL
B
A
A
Assembly Instructions
8
Step 10
Fit runners to the
right side
Fit the 2 runners
marked ‘CR’ to the right
side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
Fit the 2nd screw into
the corresponding hole
in the right side .
Step 11
J b
F
2
J b
F
2
Finished
front edge
Finished
front edge
C
C
B
Finish preparing the
right side
Tap 2 wooden dowels
into the right side .
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
B
2
C
2
A
2
2
2
CR
F
F
CR
F
F
CR
CR
B
J b
CR
CR
F
F
J b
J b
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 12
Step 13
C
C
C
A
A
A
A
C
Plain chipboard
surface
Finished
front edge
Prepare the base
Tap 4 wooden dowels
into the base .
Insert 4 large locking
nuts into the base
A
4
4
.
C
Join the right side and
base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
C
C
C
4
2
4
4
4
plain
chipboard
surface
2
Assembly Instructions
Step 14
Fit the left side
Push the left side
onto the base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Step 15
1
C
4
B
Prepare the top
Screw 4 metal dowels
into the top .
B
B
B
B
3
3
plain
chipboard
surface
10
1
4
4
Assembly Instructions
11
Step 16
Step 17
Fit the top
Push the top onto
the left side and right
side .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1
2
C
1
2
C
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about 150mm
apart.
Stand the unit up for
the next step.
6
G
6
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
6
b:
G
y
y
x
x
3
1
2
Assembly Instructions
12
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 18
Side
panel
Drawer
side
Fit the drawers
Slide the wheels on the
runners fitted to the
drawer sides over the
wheels on the runners
fitted to the side panels
and push the drawer into
position.
Assembly is complete
ALR2914
Loading...