Stratford White - 2 Door Wardrobe
Assembly Instructions - Please keep for future reference 144/4878
Dimensions
Width - 87cm
Depth - 55.1cm
Height - 195.2cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6403030
BK00760 - Issue 1 - 17/07/2014
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Due to difference in floor
levels, doors may not be
aligned. Adjustment may be
necessary.
• To prevent bowing of shelves
do not over load, and always
distribute weight evenly.
• If a residual aroma is
experienced with your new
furniture after the packaging
is removed simply ensure the
room is well ventilated and this
will assist a speedy removal
• We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• It is essential that this unit be
fixed to a wall with the fittings
provided.
• Please retain the product label
on the back of the unit, as this
information will help support any
queries.
Care and maintenance - Non compliance with this information may affect your guarantee
• Dust with a clean cloth or, if
required a slightly damp cool
cloth. Do not use household
cleaners, abrasives or polishes
as permanent damage may
occur.
• Your furniture is finished to the
required colour. Avoid exposure
to strong sunlight as this can
change the colour. Change in
appearence may also occur if
items are permanently left on a
surface.
• Do not drag the furniture or lift
it by its top.
• Avoid sharp objects, contact
with water and direct heat on all
surfaces
• From time to time check that
there are no loose screws on
this unit.
• Doors should be secured or
removed before moving.
• You should get assistance
when moving or lifting your
furniture. Furniture consisting of
more than one unit should be
disassembled before attempting
to move it.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
If you have damaged or missing components,
Components - Panels
call the Customer Helpline:
Please check you have all the panels listed below
Cornice front section
2
LH cornice return
3
0345 6403030
(87 x 7cm)
(55.5 x 7cm)
Assembled wardrobe (191 x 80 x 53.1cm)
1
RH cornice return
4
(55.5 x 7cm)
2
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings
may be supplied than are required.
A
20mm Dovetail Jointer x 2
D
15mm Screw x 1
B
9mm Dovetail Jointer x 2
E
15mm Washer x 2
C
20mm Cornice screw x 7
F
The following components are pre-fi tted and are illustrated for reference only.
White ceramic handle x 2
20mm handle screw x 2
Wall strap x 1
Tools required
Phillips screwdriver
(medium)
Small
hammer
Eye Protection
(when using
hammer)
Step ladder
(or equivalent)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50
3
55 60
65 70 75 80
85 90 95 100
105
110 115 120 125 130 135 140 145 150
155 160
165 170
Assembly Instructions
Step 1
Remove and replace
handle
a: Position the unit in
the required position. The
white ceramic handles
are fi tted to the inside of
the unit, using a Philips
screwdriver unscrew the
20mm handle screws in
each handle and remove
both the 20mm handle
screw and the white
ceramic handle.
a:
WARNING: Help may be
required for this step.
Philips screwdriver
1
b: Replace the white
ceramic handle on the
front of the unit. Fix in
position by screwing
the 20mm handle screw
20mm Handle screw
b:
into each white ceramic
handle from inside the
unit using a Philips
screwdriver.
White ceramic handle
Philips screwdriver
20mm Handle screw
4
Assembly Instructions
Step 2
Assemble Cornice
a: Work on a fl at clean
surface . Position the RH
4
cornice return
the cornice front section
2
together to make a
corner and press the
20mm dovetail jointer
A
curved edge fi rst into
the deepest slot made
by the two sections and
the 9mm dovetail
the shallowest. Tap home
fi rmly with a hammer to
make the joint tight.
and
B
into
a:
A
42
B
Small hammer
Repeat for the other joint.
b: Place the cornice
on top of the wardrobe,
you may need to use
step ladders to do this.
position the cornice being
careful to ensure that
the back edges of the
b:
WARNING: Help may be
required for this step.
Philips screwdriver
C
cornhice are fl ush with
the back of the robe and
that the overhang on
each side is equal. Once
the position is correct,
screw down fi rmly with a
philips screwdriver and
the 20mm cornice screws
C
.
Note: There are not any
pre drilled holes in the
top of the robes for this.
3
2
4
1
5
Assembly Instructions
Step 3
Fixing to wall
It is recommended that
the wardrobe is fi xed to
a wall
F
Fix wall strap
top of wardrobe using
15mm screw
15mm washer
Warning: The
15mm screw
is for fi xing the
wall strap
F
to the
D
and
E
.
D
to furniture
Using the correct type of screw
screw through the washer and wall
strap into a pre-drilled hole in the
wall
D
E
only. In addition to this
you will need to choose
a screw or fi tting which is
suitable for securing the
F
wall strap
of walls you have. If you
are unsure about what
type of screw to use seek
professional help.
to the type
Step 4
Adjusting doors
1. To adjust the height /
level of the door loosen
all screw ‘A’s on all hinge
F
E
A
plates, level the door
height and retighten all
screw ‘A’s.
2. To adjust the gap
between the doors
loosen screw ‘B’, then
turn screw ‘C’ clockwise
to close the gap or
anticlockwise to increase
the gap. Re-tighten
screw ‘B’ to lock position.
3. To adjust the distance
away from the unit
loosen screw ‘B’, this
allows the hinge arm
B
A
C
2
1
to slide back and forth.
Adjust as required then
re-tighten screw ‘B’.
Assembly is complete.
3
6
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6403030
Loading...