Argos VU-01e, VU-02e ASSEMBLY INSTRUCTIONS

Bagless Upright Vacuum Cleaner
Instruction Manual - Please keep for future reference
VU-01e VU-02e
0845 6042377
or visit www.bagsandfilters.com
Important - Please read these instructions fully before installing or using
These instructions contain important information which will help you get the best from your appliance and ensure safe and correct use and maintenance. If you need help or have damaged or missing parts, call the
Customer Helpline: 0845 6042377
Contents
Safety Information
Vacuum Cleaner
Safety Information 2
Parts 3
Initial Setup for 4 normal operation
Assembly 5-6
Operation 7
Accessories 8
Maintenance 9-10
Emptying the dirt container 9
Cleaning the HEPA media filter 9
Cleaning the pre motor filter 10
Replacing the belt 10
Clearing Blockages 11
Removing debris from 11 the Turbotool
Removing debris from 11 the hose
Removing debris from 11 the brushbar
Troubleshooting 12
Technical Specifications 13
Guarantee 14
1
Product Code
VU-01e/VU-02e
Important - Please read all instructions before use and keep for future reference
FOR HOUSEHOLD USE ONLY.
When using the vacuum cleaner, basic safety precautions should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry surfaces. Do not handle the plug or vacuum cleaner with wet hands. Do not use outdoors or on wet surfaces.
2. Turn off the vacuum cleaner controls before disconnecting or connecting from the mains supply.
3. Always unplug the vacuum cleaner before connecting or disconnecting the vacuum hose and accessories.
4. Children should be supervised to ensure that they do not play with the appliance.
5. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
6. Only use as described in this manual. Only use recommended attachments.
7. Do not use the vacuum cleaner if it has been dropped, damaged, left outdoors or dropped into water.
8. Do not use the vacuum cleaner with a damaged cord or plug. If the supply cord is damaged, call the helpline for assistance.
9. Do not pull or carry by cord/hose. Do not use the cord/hose as a handle, close a door on the cord/hose or pull cord/hose around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.
10. Do not put any objects into openings. Do not use with any openings blocked and do not restrict air-flow. Keep all openings free of dust, lint, hair or anything that might reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.
12. Do not pick up hot coals, cigarette butts, matches or any hot, smoking or burning objects.
13. Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene etc.) or use in the presence of explosive liquids or vapours.
14. Do not vacuum up harmful or toxic material (chlorine, bleach, ammonia, drain cleaner etc.).
15. Do not vacuum up hard or sharp objects such as glass, nails, screws, coins, etc. Do not use without ALL of the filters in place.
16
17. Take extra care when vacuuming on stairs.
18. Keep vacuuming area well lit.
19. Store the vacuum cleaner in a cool, dry area.
20. Turn off the on/off switch before unplugging the vacuum cleaner.
21. Only use CE-approved 13 amp extension cords. Non-approved cords may overheat. Care should be taken to arrange the cord so that the cord cannot be tripped over.
WARNING: Always switch off and unplug
the vacuum cleaner from the electrical outlet before assembling, opening or emptying the dirt container, connecting/disconnecting the attachments, or carrying out maintenance or troubleshooting checks.
CAUTION: The vacuum cleaner is a very
powerful unit. Before plugging the cord into the electrical outlet, make sure the switch is in the ‘off’ position. Hold the vacuum cleaner firmly when starting and in use.
IMPORTANT: If the inlet, hose or extension
tube is blocked, switch off the vacuum cleaner and remove the blockage(s) before re-starting the vacuum cleaner.
IMPORTANT: We recommend that filters
should be checked and cleaned periodically. For washable filters, ensure they are completely dry before inserting back into the vacuum cleaner. Do not wash with detergents. Only use warm water, max 40°C.
IMPORTANT: The motor is equipped with a
thermal cut-out. If for any reason the unit should overheat, the thermostat will automatically turn the unit off. Should this occur, unplug the vacuum cleaner from the electrical outlet and turn off the switch. Remove dirt container and empty. Clean filters. Allow the unit to cool for approximately one (1) hour. To re-start, plug into an electrical outlet and switch back on.
This vacuum cleaner is intended for household use only and NOT for commercial or industrial use.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE.
2
AssemblyParts
the Customer Helpline: 0845 6042377
Please familiarise yourself with parts and accessories listed below
If you have damaged or missing parts, call
Initial Setup for normal operation
1. Use the base accessories.
– Shortest hose
– Extension tube set to shortest practicable length.
1
2
3
4
5
6
1
Hose Crevice tool
2
Dirt container release handle
3
Extension tube
4
Dirt release button
5
Floor height adjust slider
6
Turbotool (VU-02e only)
7
Upper cord wrap
8
17
3. Dust receptacle empty.
2. Clean filters installed.
7
8
9
10
11
12
9
HEPA media filter Power cord
10
Dirt container
11
On/off button
12
Cable clip
13
Upper hose caddy/carry handle
14
Hose/tool connector
15
Lower hose caddy
16
Turbotool caddy
17
13
14
4. All Bleeds must be closed.
5. Variable Power set to Maximum.
6. Floor heads/tools set to Carpet Mode for carpet cleaning.
7. Mechanical Agitation turned ON for carpet cleaning.
15
16
8. Floor heads/tools set to Hard Floor Mode for hard floor cleaning.
9. Mechanical Agitation turned OFF for hard floor cleaning.
Filters (pre-assembled in product) Tools required for assembly
18
3
HEPA media filter
9
Pre motor filter
18
9
1 x Crosshead
screwdriver
4
Assembly
Assembly
Assembly
Assembly
Assembling your vacuum cleaner
Assembling your vacuum cleaner
1. Insert the handle into the main body of the vacuum.
2. Insert the carry handle/upper hose caddy into the back of the vacuum.
3. Secure the handle and carry handle to the unit by inserting the ‘U’ shaped pin.
Assembling your vacuum cleaner
1
2
3
5. Connect the upper hose to the
upper hose connector on the back of the vacuum cleaner. Tabs will click into place.
6. Connect the lower hose to the lower hose connector on the side of the vacuum.
7. Attach the dirt container to the unit, ensuring it is fitted correctly. The dirt container will click when secured.
5
6
7
4. Insert the three screws provided
and secure.
5
4
8. VU-02e ONLY. Slide the Turbotool
holder over the end of the handle and fit into place.
8
6
Operation Operation
SHORT PILE
CARPET
LONG PILE
CARPET
Operating the appliance Using the Hard Floor Adapter
NOTE: Do not use this vacuum on
hard floors. Intended for all carpet types only. Brushbar continually rotates when in upright position. Do not leave in one place for extended period of time. When vacuuming stairs, do not place the unit on the stairs.
1. Fully unwrap the power cord,
twisting the upper cord wrap and plug into mains.
2. Adjust the brushbar height to suit
your carpet type.
3. Turn the vacuum cleaner on using
the on/off button situated on the base of the unit.
4. Push foot on floor head to
recline handle.
1
Apply the Hard Floor Adapter for optimum results on hard floors. The Hard Floor Adapter can be used on any floor setting.
2
1. Lie vacuum cleaner on its back
exposing brush bar.
3
1
4
2. Align the Hard Floor Adapter with
the base of the vacuum cleaner, push until it clicks into place.
Accessories
1. Remove the hose from the lower
hose caddy.
2. Fit the crevice tool or the Turbotool
to the end of the hose.
NOTE: Do not use the Turbotool on suede and leather surfaces.
7
1
2
2
8
AssemblyMaintenance
WARNING: To reduce the risk of electric shock, turn the vacuum cleaner off and unplug from the electrical outlet before performing maintenance/ trouble shooting checks.
Maintenance
Emptying the dirt container
NOTE: Empty the dirt container
regularly. When maximum dust capacity is reached it is necessary to empty/clean the dirt container.
1. Remove the dirt container, lifting
the release handle.
2. Empty the dirt container over a bin
by pressing the dirt release button.
Cleaning the HEPA media filter
NOTE: Failure to keep filters clean will result in a loss of performance.
1. Remove lid of dirt container by
twisting anti clockwise.
Cleaning the pre motor filter
1
2
1. Remove the pre motor filter from
underneath the dirt container.
2. Clean the pre motor filter by tapping it against a bin and washing it under warm water (max 40˚C).
3. Leave to dry for 24 hours before returning to your machine and using your vacuum cleaner.
1
2
TAP
Replacing the belt
1
a
1. Remove the 4 screws on the base
of the unit.
1
NOTE: To remove/attach the lid to the dust container align arrows.
2. Remove the HEPA media filter by twisting anti clockwise.
3. Clean the HEPA media filter by tapping it against a bin and washing it under warm water (max 40°C).
4. Leave the filter to dry for 24 hours, before returning to the dirt bin and using your machine.
9
2
3
TAP
b
a
b
2. Remove the 2 screws underneath
the middle set of wheels.
3. Lift the floor head cover.
4. Remove the belt from the unit, by
lifting out the brushbar. Replace the belt and fit the brushbar back into the floor head.
2
3
10
AssemblyClearing Blockages
Troubleshooting
For help, spares or assistance please call: 0845 6042377 or visit www.bagsandfilters.com
Removing debris from the Turbotool (VU-02 only)
1. Remove the rubber ring from the neck of the Turbotool.
2. Lift the top cover from the Turbotool.
3. Using scissors cut any threads from the brushbar and remove.
4. To re-assemble the Turbotool align the tabs at the front of the lid and close.
Problem
There is an
1
accessory missing
The vacuum cleaner does not switch on
Possible causes Solutions
1. A part(s) is missing from box 1. Check the ‘PARTS’ page of your instructions
1. The unit is not plugged into a mains socket
2. The power button on the unit has not been depressed
3. The thermal motor cut out has been activated
4. There is no electricity to the power socket
1. Ensure the plug is firmly in the socket and switched on
2. Depress the power switch on the unit
3. If the unit has cut out during use, disconnect the unit from the wall socket, allow to cool for one hour, clean the filters, empty bin and check the hose/accessories for blockages
4. Seek expert help from a qualified electrician
2
1. Check hose/tools are correctly attached to the machine/hose/tube; refer to ‘ASSEMBLY/
1. The accessories are not correctly fitted
2. There are blockages in the
The vacuum cleaner won’t pick up
3
hose/accessory
3. The dirt container is full
4. The filters are blocked/clogged
5. The carpet height adjust slider setting is not correct
6. The belt is broken/brushbar not rotating
OPERATION’ section
2. Check the air paths of the hose/accessory are not obstructed by blockages
3. Check dirt container and if necessary empty
4. Frequently cleaning filters will maintain performance; see ‘MAINTENANCE’ section
5. See ‘OPERATION’ section for correct carpet height setting for your carpet
6. Disconnect the unit from the power supply, remove the floor head cover and check the belt has not detached from the motor spindle or that the belt is not worn/damaged; see ‘MAINTENANCE’ section
Removing debris from the hose
1. Disconnect the hose from the vacuum cleaner and remove any blockages and reconnect the hose securely.
Removing debris from the brushbar
1. Using scissors cut any threads from the brushbar and remove.
11
Dust is escaping from the vacuum cleaner
Accessories won’t pick up dust/debris
1
The blockage indicator (if applicable to model) activates
1. The filters/dirt container are not fitted correctly
2. The filters are damaged
1. The wrong tool is fitted for the task
2. The tools are blocked
3. The filters are blocked
4. The dirt container is full
5. The hose/tubes are blocked
1. The filters/dirt container are blocked
2. The dirt container is full
3. The accessories/hose/tube are blocked
1. See ‘ASSEMBLY’ and ‘MAINTENANCE’ sections
2. If the filters are damaged these will need to be replaced
1. See ‘PARTS’ section
2. Check the air paths of the tools are not obstructed by blockages
3. Frequently cleaning filters will maintain performance; check ‘MAINTENANCE’ section
4. Check and empty the dirt container
5. Check the air paths of the hose/tubes are not obstructed by blockages
1. Frequently cleaning filters will maintain performance; check ‘MAINTENANCE’ section
2. Check and empty dirt container
3. Check the air paths of the accessories/hose/ tubes are not obstructed by blockages
12
AssemblyTechnical Specifications
Model Number VU-01e/VU-02e
Voltage 220-240V~/50Hz
We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product improvements and development.
PRODUCT GUARANTEE
This product is guaranteed against manufacturing defects for a period of
Year
This product is guaranteed for twelve months from the date of original purchase. Any defect that arises due to faulty materials or workmanship will either be replaced, refunded or repaired free of charge where possible during this period by the dealer from whom you purchased the unit.
EEC statement of compliance
Manufacturer/EEC importer: Hereby on our own responsibility, declare that the VU-01e and VU-02e are manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
13
The guarantee is subject to the following provisions:
The guarantee does not cover accidental damage, misuse, cabinet parts, knobs or consumable items.
The product must be correctly installed and operated in accordance with the instructions contained in this manual.
It must be used solely for domestic purpose.
The guarantee will be rendered invalid if the product is re-sold or has been damaged by inexpert repair.
Specifications are subject to change without notice.
The manufacturer disclaims any liability for the incidental or consequential damages.
The guarantee is in addition to, and does not diminish your statutory or legal rights.
Guarantor: Argos Ltd
489 - 499 Avebury Boulevard
Central Milton Keynes
MK9 2NW
Loading...