MADE IN
BRITAIN
Dimensions
Width - 105cm
Depth - 39cm
Height - 71.5cm
Victoriana - Dressing Table and Stool
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 25/07/14
Important - Please read these instructions fully before starting assembly
244/5034
218/7794
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 30kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1
2
3
Modesty (D3013A)
(630 x 245mm)
Right Side (D3005A)
(572 x 352mm)
Left Side (D3012A)
(572 x 352mm)
4
Fly End (D3011A)
(692 x 352mm)
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
5
Base (D2993A)
(405 x 390mm)
Top (D3010A)
(1050 x 390mm)
6
Drawer Base (T324-347)
(324 x 347mm) x 3
Back (X598-372)
(598 x 372mm)
7
Small Drawer Front (D2994A)
(372 x 156mm) x 2
Large Drawer Front (D2995A)
(372 x 245mm)
Small Drawer
Back (W313-124)
(313 x 124mm) x 2
Large Drawer
Back (W313-195)
(313 x 195mm)
Small Left Drawer
Side (W350-124LH)
(350 x 124mm) x 2
Small Right Drawer
Side (W350-124RH)
(350 x 124mm) x 2
Large Left Drawer
Side (W350-195LH)
(350 x 195mm)
Large Right Drawer
Side (W350-195RH)
(350 x 195mm)
11
8 9 10
12 13 14
15 16
17
19
18
Seat Pad (FMANPAD)
(398 x 348mm)
20
Stool Side (D2225A)
(451 x 352mm) x 2
Stool Base (D2224A)
(400 x 348mm)
Stool Rail (D2226A)
(400 x 144mm) x 2
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Tools required
Rule Scissors
Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
A
Wooden dowel (F22) x 11
B
Metal dowel (F901) x 28
D
Large locking nut
(F900) x 22
E
Small locking nut
(F3) x 6
F
M
L
Nail (F51) x 11
H I
O
38mm Screw (F81) x 3
C
G
40mm Screw (F910) x 4
K
J
Bracket (F327) x 1
13mm Screw (F79) x 1
Electric drill
(only use when
drilling into walls)
N
Knock-in Peg (F171) x 12
R
Drawer runner (F1004) x 6
25mm Screw (F50) x 4
9mm Screw (F73) x 12
9mm Screw (F74) x 6
Wedgefix (F639) x 6
Plastic Nail (F91) x 4
Handle (F463) x 3
Q
P
Foot (F872) x 4
T
Allen Key (F36) x 1
S
50mm Screw (F49) x 4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
F
F
F
F
8
9
Step 2
Prepare the large
drawer front
Screw 2 metal dowels
into the large drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
7
Prepare the large
drawer sides
Insert a small locking
nut into the hole
shown on the large left
drawer side and the
large right drawer side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
F
8
9
Attach the large
drawer sides to the
large drawer front
Push the large left drawer
side and large right
drawer side onto the
back of the large drawer
front .
Turn the small locking
nuts on the large left
drawer side and large
right drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
7
F
F
9
8
B
B
7
7
8
9
Assembly Instructions
5
Step 4
M
M
8
Fit the drawer base
Slide the drawer base
down the grooves in the
large drawer sides
and and down into
the groove in the large
drawer front .
Step 5
Fit the large drawer
back
Fit the large drawer back
. between the large
drawer sides and .
Make sure that the
drawer base fits into
the groove in the large
drawer back .
Hold the large drawer
back in position and
tap the knock-in pegs
through the holes in the
large drawer sides
and .
15
8
9
7
10
8 9
15
10
10
M
8
9
9
8
15
7
8
9
10
15
8
M
M
Attach the handle
Attach a handle to the
large drawer front
using screw .
P
H
Step 6
7
H
P
7
Assembly Instructions
6
Step 7
Fit the wedgefixes
Turn the large drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
N
N
N
N
F
F
F
12
13
Step 9
Step 8
B
Prepare the 2 small
drawer fronts
Screw 2 metal dowels
into each of the small
drawer fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
11
B
B
11
Prepare the 2 pair of
small drawer sides
Insert a small locking
nut into the hole
shown on the small left
drawer side and the
small right drawer side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
F
12
13
x 2
x 2 x 2
11
Assembly Instructions
7
Step 10
B
B
F
12
13
M
M
Fit the drawer bases
Slide the drawer base
down the grooves in the
small drawer sides
and and down into
the groove in the small
drawer front .
Step 12
Fit the small drawer
backs
Fit the small drawer back
. between the small
drawer sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
small drawer sides
and .
15
12
13
11
14
12 13
15
14
14
M
12
13
M
M
15
12
13
15
14
12
13
Step 11
Attach the small
drawer sides to the
small drawer frontS
Push the small left drawer
side and small right
drawer side onto the
back of the small drawer
front .
Turn the small locking
nuts on the small left
drawer side and
small right drawer side
. .
12
13
11
F
13
12
x 2
x 2
x 2
11
Assembly Instructions
8
Step 13
Step 14
H
P
Fit the wedgefixes
Turn the small drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
N
N
Attach the handle
Attach a handle to the
small drawer front
using screw .
P
H
11
N
N
11
x 2
x 2
A
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 15
Finished
front edge
K
R
a:
b:
c:
Prepare one surface
of the left side
a: Place 3 runners on
the left side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Tap 2 wooden
dowels into the left
side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Turn the left side over for
the next step
1
K
K
E
1
R
R
1
1
E
A
10mm
A
K
R
K
K
K
K
R
K
R
E
E
A
1
1
1
A
Assembly Instructions
10
Step 16
Prepare the other
surface of the left
side
Screw 2 metal dowels
into the left side .
Step 17
1
B
Prepare the right side
a: Place 3 runners on
the right side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Tap 2 wooden
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
2
K
K
E
2
R
R
2
a:
b:
c:
A
2
Finished
front edge
K
R
B
B
1
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
K
R
K
K
K
K
R
K
R
E
E
A
2
2
2
Finished
top edge
Polystyrene
block
Polystyrene
block
Assembly Instructions
11
Step 18
Step 19
Fit the base
Fit the base onto the
side panels and
using 4 screws .
Note: To make it easier
to fit the base panel,
place polystyrene blocks
from the packaging
underneath the side
panels to raise the
assembly.
G
6
1 2
Fit the 4 feet
Fit the 4 feet to the
base using screws
and tighten them using
the allen key .
Note: You may find it
easier to turn the foot as
the screw is held with
the allen key.
Step 20
Q
S
6
Prepare the modesty
Insert 4 large locking
nuts into the modesty
. .
4
E
G
G
plain
chipboard
surface
6
G
G
1
2
T
S
Q
Q
Q
Q
6
E
E
E
E
4
T
Polystyrene
block
Polystyrene
block
Finished
top edge
A
Assembly Instructions
12
Step 21
Step 22
Prepare the fly end
Insert 2 large locking
nuts into the fly end
. .
Screw 2 metal dowels
into the fly end .
Tap a wooden dowel
into the fly end .
3
E
B
3
3
A
Join the fly end and
modesty
Push the modesty
onto the fly end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
4
3
E
4
Fit the modesty and
fly end
Push the modesty
and fly end assembly
onto the left side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
Note: Place polystyrene
blocks underneath the fly
end.
4
3
1
E
4
Step 23
E
E
B
B
3
3
4
4
1
3
Assembly Instructions
13
Step 24
4
1
3
Fit 2 plastic nails
Tap 2 plastic nails
into the bottom edge of
the fly end as shown.
Using 2 people,
carefully stand the
unit up.
O
3
O
O
Warning: The
unit is heavy.
Lift with care.
Prepare the top
Screw 6 metal dowels
into the underside of the
top .
Screw the bracket
onto the top , flush to
the back edge and
central, using screw .
5
B
C
5
J
Step 25
B
B
B
B
B
B
C
J
Profiled
front edge
5
plain chipboard surface
xx
yy
Assembly Instructions
14
Step 26
Fit the top
Lower the top down
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the left side , right
side and fly end .
Using 2 people,
carefully lay the unit
back down onto its
front edges.
5
E
1
2 3
3
1
2
5
Step 27
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced out evenly.
Using 2 people,
carefully stand the
unit up again.
16
D
16
Polystyrene
block
yy
xx
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
D
16
Warning: The
unit is heavy.
Lift with care.
Warning: The
unit is heavy.
Lift with care.
Fit the drawers
Starting with the large
bottom drawer, slide
both the runners
forward and locate the
drawer sides
between them, lining up
the holes in the drawer
sides with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
sides and out into the
2nd threaded hole in the
runner.
Note: Do not overtighten the screws .
If they catch on the
runner you may need
to loosen them slightly.
Assembly Instructions
15
Step 28
Step 29
Secure unit to a wall
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the metal
bracket fitted to the
top of the unit.
Fixings are not supplied
as they will need to suit
the wall type, and the
length of Screw will
depend on the distance
of the back of the Unit to
the wall.
Warning: Take
care when
drilling the wall that you
do not drill into any
pipes, wires etc. If in
doubt, consult an expert.
C
5
C
WALL
WALL
Top of unit
5
C
5
L
R
R
L
2nd threaded
hole
R
L
L
L
Assembly Instructions
16
Step 30
A
Prepare the 2 stool
sides
Screw 6 metal dowels
into each of the 2 stool
sides , as shown.
Step 31
B
Prepare the stool
base
Insert 4 large locking
nuts into the holes in
the stool base .
Tap 2 wooden dowels
into the ends of the stool
base .
18
17
17
E
A
B
18
E
E
E
E
A
17
x 6
x 2
Fit a stool side to the
stool base
Fit one of the stool
sides to the stool
base .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the stool base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
18
17
E
E
17
18
17
Step 32
Assembly Instructions
17
Step 33
Fit the stool rails
Push the 2 stool rails
down onto the stool side
, as shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each stool rail .
19
18
E
19
18
19
19
A
Step 34
Step 35
Prepare the 2 stool
rails
Insert 4 large locking
nuts into each of the
2 stool rails .
Tap 2 wooden dowels
into each stool rail .
E
14
E
E
E
E
A
A
14
14
x 2
Fit the other stool
side
a: Push the other stool
side down onto the
assembly, as shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the stool base .
b: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the stool rails .
18
17
18
E
17
b:
a:
E
19
b:
19
19
Assembly Instructions
18
Step 36
Step 37
I
Fit the seat pad
Position the seat pad
onto the assembly and
make sure that its 4
edges line up with the
stool base .
Hold the seat pad in
position and screw up
through the 4 holes in
the stool base using
screws .
Note: Make sure that
you screw into the hard
surface of the seat pad.
20
17
I
20
17
20
17
Hard
surface
Soft
surface
I
I
I
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each stool side as
shown.
O
18
O
O
O
O
18
18
Assembly Instructions
19
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 38
Assembly is complete
Warning: The
unit is heavy.
Lift with care.
ALR3064
Loading...