Argos Victoriana - 1 Drawer 2 Door Robe ASSEMBLY INSTRUCTIONS
MADE IN
BRITAIN
Dimensions
Width - 72cm
Depth - 49cm
Height - 195cm
Victoriana - 1 Drawer 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 18/07/14
Important - Please read these instructions fully before starting assembly
230/2146
230/6142
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 48kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step ladder
Electric drill
(do not use
for fitting
screws)
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (D3016A)
(1810 x 457mm)
Right Side (D3017A)
(1810 x 457mm)
1
7
13
2
14
8
6
10
12
9
3
4
5
Hanging Rail (FHR649)
(649mm long)
11
Door (D3019A)
(1553 x 339mm) x 2
Top (D3014A)
(718 x 490mm)
Base (D3015A)
(718 x 490mm)
Horizontal (D3018A)
(659 x 456mm)
Drawer Front (D3000A)
(685 x 245mm)
Left Drawer
Side (W370-195LH)
(370 x 195mm)
Drawer Base (T637-367)
(637 x 367mm)
Right Drawer
Side (W370-195RH)
(370 x 195mm)
Back (X1836-685)
(1836 x 685mm)
Back Rail (D3020A)
(659 x 123mm)
Drawer Back (W626-195)
(626 x 195mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
N
L
T
Small locking
nut (F3) x 2
C
Nail (F51) x 33
40mm Screw (F910) x 12
S
J
9mm Screw (F74) x 2
K
9mm Screw (F73) x 4
Drawer runner (F1004) x 2
38mm Screw (F81) x 4
Knock-in Peg (F171GY) x 4
Large locking
nut (F900) x 2
Metal dowel (F901) x 4
Wooden dowel (F22) x 2
R
M
Handle (F463) x 4
Wedgefix (F639) x 4
Foot (F872) x 4
P
Q
Hinge (F518) x 6
Hinge plate
(F523) x 6
O
Bracket (F327) x 1
13mm Screw (F63) x 14
Rail holder
(F1014) x 2
13mm Screw (F79) x 1
V
Allen Key (F36) x 1
U
50mm Screw (F49) x 4
6
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
A
B
A
C
C
C
C
8
9
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
6
C
C
9
8
A
A
6
8
9
Loading...