Page 1
Dimensions
Width - 80cm
Depth - 33cm
Height - 125.5cm
Venetia - Boot Storage
Assembly Instructions - Please keep for future reference
Issue 2 - 29/07/13
904/2193
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 40kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Page 3
2
1
2
5
3
4
7
12
8
13
10
9
6
11
Top/Base (D1929A)
(797 x 329mm) x 2
Divider (D1933A)
(1062 x 310mm)
Rail (D1934A)
(762 x 96mm)
Shelf (D1935A)
(373.5 x 308mm) x 7
Door (D1937A)
(1056 x 391.5mm) x 2
Left Side (D1930A)
(1203 x 312mm)
Right Side (D1931A)
(1203 x 312mm)
Drawer Front (D1936A)
(786 x 138mm)
Drawer Base (T457)
(739 x 297mm)
Drawer Back (W455)
(728 x 95mm)
Left Drawer Side (W410LH)
(300 x 95mm)
Right Drawer Side (W410RH)
(300 x 95mm)
Back (X933)
(1225 x 784mm)
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Page 4
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
Wooden dowel (F22) x 2
C
D E F
G H I
Nail (F51) x 27
M
Hinge plate
(F523) x 4
13mm Screw (F79) x 1 13mm Screw (F63) x 8
L
O
B
Metal dowel (F901) x 16
Large locking
nut (F900) x 14
Small locking
nut (F3) x 2
Knock-in Peg (F171) x 4
N
Bracket (F327) x 1
J
9mm Screw (F74) x 2
Shelf support (F121) x 28
P
Drawer runner (F1004) x 2
K
9mm Screw (F73) x 4
Hinge (F518) x 4
25mm Screw (F50) x 10
Q
Handle (F236) x 3
R
Feet (F854) x 4
S
Door Buffer (F137) x 2
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Page 5
4
Step 1
B
B
B
6
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the back of the
drawer front .
Note: Tighten metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
F
10
11
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
11
6
F
10
11
F
F
F
10
11
B
B
F
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Small groove
11
6
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
10
F
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Page 6
E
E
Assembly Instructions
5
Step 4
6
10
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
12
10 11
6
9
10 11
12
9
9
E
10 11
Attach the handle
Attach a handle to the
drawer front using 2
screws .
6
Q
G
11
6
10
11
E
E
9
H
H
H
6
12
12
Page 7
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
K
P
K
P
Prepare the left side
a: Place a runner on
the left side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Fit 2 hinge plates
onto the left side ,
making sure that the slot
is facing towards the
finished front edge.
Screw a metal dowel
into the left side .
Insert 4 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
1
K
K
P
P
1
L
1
1
B
K
B
C
C
L
L
C
C
1
1
1
L
a:
b:
c:
C
C
1
Page 8
Assembly Instructions
7
Step 8
Prepare the right side
a: Place a runner on
the right side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Fit 2 hinge plates
onto the right side ,
making sure that the slot
is facing towards the
finished front edge.
Screw a metal dowel
into the right side .
Insert 4 large locking
nuts into the right
side .
2
K
K
P
P
2
L
2
2
B
C
2
Finished
front edge
K
M
K
P
Finished
front edge
2
Finished
front edge
2
Finished
front edge
2
K
L
L
B
C
C
C
C
L
a:
b:
c:
Page 9
Finished
front edge
Assembly Instructions
8
Step 9
A
Prepare the rail
Screw 2 metal dowels
into the rail .
Insert 2 large locking
nuts into the rail .
Tap 2 wooden dowels
into the rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
B
4
C
4
10mm
A
A
4
B
C
C
C
B
B
A
4
Join the right side and
rail
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
Note: Turn the large
locking nut as far as it
will go - more than 1/2 a
turn.
Step 10
4
2
C
C
2
4
4
Page 10
Finished
front edge
Assembly Instructions
9
Step 11
Fit the left side
Push the left side
onto the rail .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
4
1
C
4
4
1
Step 12
Finished
front edge
Prepare the divider
Insert 4 large locking
nuts into the divider
. .
C
7
C
C
C
C
7
Page 11
Finished
front edge
Assembly Instructions
10
Step 13
Fit the divider
Push the divider onto
the rail .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
4
7
C
7
4
7
Prepare the base
Screw 6 metal dowels
into the base .
B
3
Finished
front edge
B
B
B
B
B
B
Step 14
Page 12
Finished
front edge
Assembly Instructions
11
Step 15
Fit the base
Push the base onto
the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the left side , right
side and divider .
3
C
1
2 7
Prepare the top
Screw 4 metal dowels
into the top .
Fix the bracket in the
middle of the top
flush to the back edge,
using screw .
B
3
Finished
front edge
B
B
B
B
Step 16
H
N
N
3
H
N
3
7
3
1
2
Note: To make it easier to fit
the base and top panels,
place polystyrene blocks from
the packaging underneath the
sides and divider.
Page 13
Assembly Instructions
Step 17
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted
to the left side
and right
side .
3
C
1
2
3
1
2
R
R
R
R
G
10mm
10mm
Step 18
Fit the feet
Screw the 4 feet onto
the base using
screws .
Note: Position the feet
approximately 10mm in
from the edges of the
base.
R
G
3
R
12
3
Page 14
Assembly Instructions
13
Step 19
yy
y
x
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about
150mm apart.
Stand the unit up
for the next step.
13
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
13
D
9
Warning: The
unit is heavy.
Lift with care.
x
Page 15
Assembly Instructions
Step 20
14
N
Secure unit to a wall
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by use of the metal
bracket fitted under
the top of the unit.
Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the unit to
the wall.
Warning: Take
care when
drilling the wall that you
do not drill into any
pipes, wires etc. If in
doubt, consult an expert.
3
WALL
WALL
Top of unit
N
N
Page 16
Assembly Instructions
15
Step 21
Fit the drawer
Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
sides with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runners.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
J
P
P
J
2nd threaded
hole
P
J
10 11
J
J
10
11
Page 17
Assembly Instructions
Step 22
16
O
x 4
O
x 4
O
x 4
O
x 4
O
x 4
O
x 4
Step 23
Fit the shelves
For each of the 7
shelves , insert 4 shelf
studs at the required
height on either side of
the unit.
Lower the 7 shelves
down onto the shelf
studs .
Make sure that the
plastic sleeve is
fully pushed onto
the shelf stud.
5
O
5
O
Prepare the 2 doors
Push fit 2 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
I
M
8
x 2
5
5
5
5
5
5
5
O
x 4
90
M
M
I
I
M
I
I
8
Page 18
Small piece of
waste wood
Assembly Instructions
17
Step 24
8
Drill 2 handle holes in
each of the doors
Important: Please follow
these instructions
carefully.
Lay the 2 doors
down onto a smooth
surface.
Check that the hinges
and holes are in the
same place as the
diagrams.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
IMPORTANT
Carefully choose which 2 holes
you need to drill in each door
8
8
ONLY drill these
2 holes in 1 door
Small piece of
waste wood
ONLY drill these
2 holes in 1 door
This will be the
left hand door
This will be the
right hand door
Page 19
Assembly Instructions
Step 25
18
Q
Fit doors, handles and
door buffers
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
Stick a door buffer
into the top corner of
each door so that
they hit the front edge of
the divider when the
door is closed.
M
M
M
L
L
L
M
L
Q
G
8
e:
a: b:
c: d:
L
M
L
L
B
L
M
M
M
A
M
L
B
G
G
8
8
S
Note: The easiest way to
attach each door is to fit the
top hinge first, then align
and fit the other hinge.
S
8
Page 20
Assembly Instructions
19
ALR2822
Step 26
Warning: The
unit is heavy.
Lift with care.
Assembly is complete
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
b:
c:
d:
a:
A
A
B
C
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Page 21
Dimensions
Width - 80cm
Depth - 33cm
Height - 125.5cm
Venetia - Boot Storage
Assembly Instructions - Please keep for future reference
Issue 3 - 14/01/15
904/2193
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Page 22
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 40kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Page 23
2
1
2
5
3
4
7
12
8
13
10
9
6
11
Top/Base (D1929A)
(797 x 329mm) x 2
Divider (D1933A)
(1062 x 310mm)
Rail (D1934A)
(762 x 96mm)
Shelf (D1935A)
(373.5 x 308mm) x 7
Door (D1937A)
(1056 x 391.5mm) x 2
Left Side (D1930A)
(1203 x 312mm)
Right Side (D1931A)
(1203 x 312mm)
Drawer Front (D1936A)
(786 x 138mm)
Drawer Base (T457)
(739 x 297mm)
Drawer Back (W455)
(728 x 95mm)
Left Drawer Side (W410LH)
(300 x 95mm)
Right Drawer Side (W410RH)
(300 x 95mm)
Back (X933)
(1225 x 784mm)
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Page 24
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
Wooden dowel (F22) x 2
C
D E F
G H I
Nail (F51) x 27
M
Hinge plate
(F523) x 4
13mm Screw (F63) x 8
L
O
B
Metal dowel (F901) x 16
Large locking
nut (F900) x 14
Small locking
nut (F3) x 2
Knock-in Peg (F171) x 4
N
J
9mm Screw (F74) x 2
Shelf support (F121) x 28
P
Drawer runner (F1004) x 2
K
9mm Screw (F73) x 4
Hinge (F518) x 4
25mm Screw (F50) x 10
Q
Handle (F236) x 3
R
Feet (F854) x 4
Door Buffer (F137) x 2
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Page 25
4
Step 1
B
B
B
6
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the back of the
drawer front .
Note: Tighten metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
F
10
11
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
11
6
F
10
11
F
F
F
10
11
B
B
F
Small groove
11
6
10
F
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Page 26
E
E
Assembly Instructions
5
Step 4
6
10
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
12
10 11
6
9
10 11
12
9
9
E
10 11
Attach the handle
Attach a handle to the
drawer front using 2
screws .
6
Q
G
11
6
10
11
E
E
9
H
H
H
6
12
12
Page 27
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
K
P
K
P
Prepare the left side
a: Place a runner on
the left side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Fit 2 hinge plates
onto the left side ,
making sure that the slot
is facing towards the
finished front edge.
Screw a metal dowel
into the left side .
Insert 4 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
1
K
K
P
P
1
L
1
1
B
K
B
C
C
L
L
C
C
1
1
1
L
a:
b:
c:
C
C
1
Page 28
Assembly Instructions
7
Step 8
Prepare the right side
a: Place a runner on
the right side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Fit 2 hinge plates
onto the right side ,
making sure that the slot
is facing towards the
finished front edge.
Screw a metal dowel
into the right side .
Insert 4 large locking
nuts into the right
side .
2
K
K
P
P
2
L
2
2
B
C
2
Finished
front edge
K
M
K
P
Finished
front edge
2
Finished
front edge
2
Finished
front edge
2
K
L
L
B
C
C
C
C
L
a:
b:
c:
Page 29
Finished
front edge
Assembly Instructions
8
Step 9
A
Prepare the rail
Screw 2 metal dowels
into the rail .
Insert 2 large locking
nuts into the rail .
Tap 2 wooden dowels
into the rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
B
4
C
4
10mm
A
A
4
B
C
C
C
B
B
A
4
Join the right side and
rail
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
Note: Turn the large
locking nut as far as it
will go - more than 1/2 a
turn.
Step 10
4
2
C
C
2
4
4
Page 30
Finished
front edge
Assembly Instructions
9
Step 11
Fit the left side
Push the left side
onto the rail .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
4
1
C
4
4
1
Step 12
Finished
front edge
Prepare the divider
Insert 4 large locking
nuts into the divider
. .
C
7
C
C
C
C
7
Page 31
Finished
front edge
Assembly Instructions
10
Step 13
Fit the divider
Push the divider onto
the rail .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
4
7
C
7
4
7
Prepare the base
Screw 6 metal dowels
into the base .
B
3
Finished
front edge
B
B
B
B
B
B
Step 14
Page 32
Finished
front edge
Assembly Instructions
11
Step 15
Fit the base
Push the base onto
the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the left side , right
side and divider .
3
C
1
2 7
Prepare the top
Screw 4 metal dowels
into the top .
B
3
Finished
front edge
B
B
B
B
Step 16
3
7
3
1
2
Note: To make it easier to fit
the base and top panels,
place polystyrene blocks from
the packaging underneath the
sides and divider.
Page 33
Assembly Instructions
Step 17
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted
to the left side
and right
side .
3
C
1
2
3
1
2
N
N
N
N
G
10mm
10mm
Step 18
Fit the feet
Screw the 4 feet onto
the base using
screws .
Note: Position the feet
approximately 10mm in
from the edges of the
base.
N
G
3
N
12
3
Page 34
Assembly Instructions
13
Step 19
yy
y
x
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about
150mm apart.
Stand the unit up
for the next step.
13
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
13
D
9
Warning: The
unit is heavy.
Lift with care.
x
Page 35
Assembly Instructions
Step 20
14
Fit the drawer
Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
sides with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runners.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
J
P
P
J
2nd threaded
hole
P
J
10 11
J
J
10
11
Page 36
Assembly Instructions
15
Step 21
O
x 4
O
x 4
O
x 4
O
x 4
O
x 4
O
x 4
Step 22
Fit the shelves
For each of the 7
shelves , insert 4 shelf
studs at the required
height on either side of
the unit.
Lower the 7 shelves
down onto the shelf
studs .
Make sure that the
plastic sleeve is
fully pushed onto
the shelf stud.
5
O
5
O
Prepare the 2 doors
Push fit 2 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
I
M
8
x 2
5
5
5
5
5
5
5
O
x 4
90
M
M
I
I
M
I
I
8
Page 37
Assembly Instructions
Step 23
16
Small piece of
waste wood
8
Drill 2 handle holes in
each of the doors
Important: Please follow
these instructions
carefully.
Lay the 2 doors
down onto a smooth
surface.
Check that the hinges
and holes are in the
same place as the
diagrams.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
IMPORTANT
Carefully choose which 2 holes
you need to drill in each door
8
8
ONLY drill these
2 holes in 1 door
Small piece of
waste wood
ONLY drill these
2 holes in 1 door
This will be the
left hand door
This will be the
right hand door
Page 38
Assembly Instructions
17
Step 24
Q
Fit doors, handles and
door buffers
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
Stick a door buffer
into the top corner of
each door so that
they hit the front edge of
the divider when the
door is closed.
M
M
M
L
L
L
M
L
Q
G
8
e:
a: b:
c: d:
L
M
L
L
B
L
M
M
M
A
M
L
B
G
G
8
8
H
Note: The easiest way to
attach each door is to fit the
top hinge first, then align
and fit the other hinge.
H
8
Page 39
Assembly Instructions
Step 25
18
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
b:
c:
d:
a:
A
A
B
C
Page 40
Assembly Instructions
19
ALR2822
Step 26
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Fit the overbalance
protector kit
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
R
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
R
R
Example
Screw
(not supplied)
Washer
Screw
UNIT
Loading...