Argos Valencia - Tall Appliance Cabinet ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 60cm

Depth - 59cm

Height - 213cm

Valencia - Tall Appliance Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 05/08/14

Important - Please read these instructions fully before starting assembly

hygena

656/5824

633/3733

633/3757

204/9533

633/3740

204/7786

Cabinet

Black Door Pack

Cream Door Pack

Oak Door Pack

White Gloss Door Pack

White HN Door Pack

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 44kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule

Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the brackets supplied.

• Dispose of all packaging carefully and responsibly.

Spirit level

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

2

5

4

7

6

Fixed Shelf (DPF108A)

(569 x 494mm) x 2

Loose Shelf (DPF079A)

(568 x 431mm) x 2

Top/Base (DPF078A)

(569 x 494mm) x 2

Left Side (DPF106A)

(1980 x 560mm)

Right Side (DPF107A)

(1980 x 560mm)

3

Lower Back (DPF111A)

(579 x 714mm)

Upper Back (DPF110A)

(579 x 582mm)

NOTE: The front surface of

the doors and fascia are

protected with a peel-off film

8

Appliance Fascia (DPF154B)

(597 x 80mm)

9

Door (DPF148B)

(597 x 716mm)

10

Drawerline Door (DPF150B)

(597 x 572mm)

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 24

B

Metal dowel (F901) x 16

C

D

Large locking nut (F900) x 16

F

G H I a

I c

I d

I e

I b

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J K

13mm Screw (F63) x 8

E

13mm Screw (F79) x 14

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

25mm Screw (F50) x 12

N

Hinge Cover (F119) x 4

Bracket (F945) x 8

Shelf support (F110) x 8

Hinge Plate (F117) x 4

Hinge Arm (F118) x 4

Leg Bracket (F127) x 2

Leg Socket (F120) x 4

Leg Clip (F128) x 2

16mm Screw (F129) x 16

Leg (F122) x 4

h

ygen

a

OOa

b

25mm Screw (F132) x 4

Handle (F214) x 2

4

Step 1

Step 2

Prepare the left side

Refer to step 1 and, if required, fit 4 hinge

plates onto the left side , as shown.

Screw 8 metal dowels into the left side .

Note: Tighten the metal dowels up fully against the panels.

B

L

J

1

If you would

like your doors

to open this

way, fit the

hinge plates to

the left side

If you would

like your doors

to open this

way, fit the

hinge plates to

the right side

Choose which way you would like the doors to open

You can fit the doors to the left side or right side.

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1

L

B

5

Step 3

A

L

Prepare the right side

Refer to step 1 and, if required, fit 4 hinge

plates onto the right side , as shown.

Screw 8 metal dowels into the holes shown on the right side .

2

B

2

B

L

2

A

C

A

C

Prepare the base and top

Insert 4 large locking nuts into the base and top as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base and top . as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

C

5

10mm

A

5

Step 4

5

Assembly Instructions

2

L

B

Assembly Instructions

6

Step 5

Finished

front edge

Finished

front edge

Join the base and top to the right side

Push the top and base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the top and base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

5

55

2

C

Step 6

B

C

5

2

I a I a

I b

b: c: d:

Fit the legs to the base

a: Push the leg sockets

. into the holes in the base as shown.

b: Secure each leg

socket with 3 screws .

c: Tap in the centre plug

on each leg socket .

d: Push the leg into

the leg socket .

I a

I e

5

x 3

I a

I b

I a

5

I a

Assembly Instructions

7

Step 7

Prepare the 2 fixed shelves

Insert 4 large locking nuts into the fixed shelves as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the fixed shelves . .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

C

6

A

6

A

C

6

A

C

6

Assembly Instructions

8

Step 8

Step 9

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the large locking nuts fitted to the base , top and fixed shelves .

Note: Turn the large locking nuts as far as they will go

- more than 1/2 a turn.

6

1

C

5 5

5

1

Finished

front edge

Finished

front edge

Fit the fixed shelves

Push the fixed shelves . onto the right side . .

Use a screwdriver to tighten the 2 large locking nuts fitted to the fixed shelves .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

6

2

C

2

6

Assembly Instructions

9

Step 10

Step 11

5

Fit the back

Slide the upper back along the grooves in the side panels and .

Slide the lower back along the grooves in the side panels and .

The top edge of the upper back must be flush with the top edge of the top .

The bottom edge of the lower back must be flush with the bottom edge of the base .

Secure the top and bottom of the 2 backs . and to the unit using 12 screws as shown.

3

5

4

5

F

3

4

3 4

Fit 4 Brackets

Fix 4 brackets against the lower fixed shelf .

Push each bracket up against the lower fixed shelf and screw it to the side panel using screws .

3

1 2

4

1 2

2

1

6

J

E

J

6

E

J

Assembly Instructions

10

Step 12

5mm

G

H

Joining units together

Fittings have been supplied so you are able to join units together.

Make sure that your first unit is level.

Push the other unit up against first unit and ensure both units are level.

Check that the ends are flush and in line, then clamp them together.

Using a 5mm drill bit, drill 2 holes (approximate positions shown circled) in the side panel into the adjoining side panel of the other unit.

Push the connecting sleeves into the holes and then screw the connecting bolts in from the other side.

G

H

Assembly Instructions

11

Step 15

Prepare the doors

Push fit 2 hinges into the drawerline door and door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.

M

D

M

10

8

10

90

M

D

M

D

M

D

M

D

8

Fit the loose shelves

Insert 4 shelf studs at the required height for each of the shelves .

Lower the loose shelves . down onto the shelf studs .

K

7

K

x 4

7

Step 14

K

x 4

Step 13