Argos Valencia - Corner Base Cabinet, 633-2947, 633-2789, 204-5977, 633-2868 ASSEMBLY INSTRUCTIONS

...

MADE IN

BRITAIN

Dimensions

Width - 88cm

Depth - 88cm

Height - 87cm

Valencia - Corner Base Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 05/08/14

Important - Please read these instructions fully before starting assembly

hygena

656/5800

633/2947

633/2789

204/5977

633/2868

205/3189

Black Door Pack

Cream Door Pack

Oak Door Pack

White Gloss Door Pack

White HN Door Pack

Cabinet

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 34kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 to 5.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top/Base (DPF136A)

(800 x 800mm) x 2

Left/Right Back (DPF139A)

(630 x 717mm) x 2

Loose Shelf (DPF137A)

(798 x 798mm)

Back (DPF138A)

(272 x 688mm)

Left/Right Side (DPF177A)

(720 x 560mm) x 2

Door (DPF145B)

(297 x 716mm) x 2

The front

surface of this

door is

protected with

a peel-off film

Please check you have all the fittings listed below

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 16

Metal dowel (F901) x 8

Large locking nut (F900) x 8

G H I a

I c

I d

I e

I b

J K

13mm Screw (F63) x 8

13mm Screw (F79) x 2

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

L M

N O

QNP

25mm Screw (F50) x 18

Bracket (F945) x 2

Leg Bracket (F127) x 3

Leg Socket (F120) x 6

Leg Clip (F128) x 3

16mm Screw (F129) x 24

Leg (F122) x 6

40mm Screw (F910) x 2

Shelf support (F110) x 7

2mm Hinge Plate (F157) x 2

Bent Hinge Arm (F154) x 2

Cantilevered

Hinge Arm

(F155) x 2

Soft Close Unit (F156)

x 2

4mm Hinge Plate (F158) x 2

Valencia Door Handle (F214) x 1

R a R b

25mm Screw (F132) x 2

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Q N

Choose which way you would like the door to open

You can fit the door to the left side or right side.

If you would like your door

to open this way, fit the

hinge plates to the left side

If you would like your door

to open this way, fit the

hinge plates to the right side

H=2

Prepare the left side

Refer to step 1 and, if required, fit 2 hinge

plates onto the left side , making sure that they face the same way as the diagram.

Screw 4 metal dowels into the holes shown on the left side .

Note: Tighten metal dowels up fully against the panels.

Fit a bracket flush to the top and back edge of the left side .

Secure the bracket using screw .

H=4

H=2

Assembly Instructions

Step 3

Step 4

Prepare the right side

Refer to step 1 and, if required, fit 2 hinge

plates onto the right side , making sure that they face the same way as the diagram.

Screw 4 metal dowels into the holes shown on the right side .

Note: Tighten metal dowels up fully against the panels.

Fit a bracket flush to the top and back edge of the right side .

Secure the bracket using screw .

C C

Prepare the top and base

Insert 4 large locking nuts into the top and base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the top and base . as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

10mm

Q N

H=2H=4

H=4

H=2

+ 14 hidden pages