Argos Valencia - 1000mm Wall Cabinet ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Cabinet
Black Door Pack
Cream Door Pack
Grey Door Pack
Plum Door Pack
Dimensions
Width - 100cm
Depth - 34cm
Height - 72cm
Valencia - 1000mm Wall Cabinet
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 15/09/11
Important - Please read these instructions fully before starting assembly
hygena
656/5745
633/2882
633/2710
656/5295
656/4540
633/2806
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 16.5kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the brackets supplied.
• Dispose of all packaging carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Electric drill
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
2
End Panel (DPF141A)
(320 x 716mm) x 2
5
Loose Shelf (DPF098A)
(968 x 236mm)
4
Top/Base Panel (DPF097A)
(969 x 319mm) x 2
Back Panel (DPF099A)
(979 x 694mm)
Muntin Rail (DPF100A)
(36 x 688mm)
6
Valencia Door (DPF147A)
(497 x 716mm) x 2
The front surface
of this door is
protected with a
peel-off film
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 8
C
D
Large locking nut (F900) x 8
F
G H
K
I
N
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
13mm Screw (F63) x 8
E
19mm Connecting bolt (F461) x 2
M
25mm Screw (F50) x 4
Connecting Sleeve (F432) x 2
Shelf support (F110) x 5
Hinge Cover (F119) x 4
h
ygen
a
J
Wall bracket (F198) x 2
Hanging bracket
(F849) x 2
L
Hinge Arm (F118) x 4
Hinge Plate (F117) x 4
40mm Screw (F910) x 2
OOa
b
25mm Screw (F132) x 4
Handle (F214) x 2
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
K
Prepare the left end panel
Fit 2 hinge plates onto the left end panel , orientated as shown.
Screw 4 metal dowels into the holes shown on the left end panel .
Note: Tighten metal dowels up fully against the panels.
Fit a hanging bracket to the left side using 2 screws , making sure that the hook is towards the back edge.
Step 2
1
B
1
B
K
K
B
B
B
B
This will be the
left end panel
1
J
G
G
J
1
G
1
K
B
B
B
B
1
This will be the right end panel
K
Prepare the right end panel
Fit 2 hinge plates onto the right end panel , orientated as shown.
Screw 4 metal dowels into the holes shown on the right end panel .
Note: Tighten metal dowels up fully against the panels.
Fit a hanging bracket to the right side using 2 screws , making sure that the hook is towards the back edge.
1
B
1
J
1
G
J
G
G
K
1
K
K
Loading...
+ 11 hidden pages