MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 45cm
Height - 72cm
Tyler - Desk
Assembly Instructions - Please keep for future reference
161/5683
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 02/05/14
Important - Please read these instructions fully before starting assembly
170/7553
151/7451
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
Left Side (D0283A)
(706 x 394mm)
1
Top (D0275A)
(1000 x 444mm)
4
Base (D0282A)
(349 x 392mm)
5
Upright (D0278A)
(706 x 394mm)
2
Right Side (D0276A)
(706 x 394mm)
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Shelf (D0285A)
(349 x 373mm)
6
Drawer Base (T161)
(299 x 330mm)
10
Modesty (D0277A)
(602 x 157mm)
7
Drawer Front (D0284A)
(345 x 157mm)
9
Door (D0288A)
(443 x 345mm)
12
Back (X725)
(626 x 373mm)
13
Plinth (D0022A)
(349 x 80mm)
8
Drawer Wrap (W161)
(943 x 95mm)
11
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 8 Shelf stud (F110) x 4
C
D
Large locking
nut (F900) x 6
E
Small locking
nut (F3) x 2
F
G
40mm Screw (F910) x 10
H I
25mm Screw (F50) x 4
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Handle (F1091) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Hinge plate
(F523) x 2
M N
R (F601)
L (F600)
F599
F599
Drawer stops (F599) x 2
Runners (F600) x 1 and (F601) x 1
Hinge (F522) x 2
L
Nail holder (F149) x 1
K
Nail (F51) x 14
J
13mm Screw (F63) x 4
Assembly Instructions
4
Prepare drawer front
and wrap
a: Screw 2 x metal
dowels into the holes
shown on the back of the
drawer front .
Note: Tighten metal
dowels up fully against
the panel.
b: Insert 2 small locking
nuts into the holes
shown on the drawer
wrap .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
B
9
a:
b:
F
11
B
Assemble drawer
a: Place drawer base
into the narrow slot on
the drawer wrap .
Fold wrap around the
base.
b: Turn drawer wrap
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10 10
11
9
F
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
B
B
B
9
9
9
11
11
11
11
B
B
F
a:
b:
B
F
11
F
F
Step 1
Step 2
Assembly Instructions
5
Attach drawer stops
Carefully break off the 2
drawer stops (F599) from
the pair of drawer
runners .
Push the drawer stops
fully through the drawer
wrap from the inside.
M
SNAP!
SNAP!
F599
11
11
Attach handle
Attach handle to the
drawer front using 2 x
screws .
Note: Do not
overtighten the screws.
D
H
D
M
M
F599
M
F599
M
F599
M
H
H
Step 3
Step 4
Assembly Instructions
6
L
F600
Finished
front edge
Finished
front edge
M
E
E
E
E
E
M
M
1
2
Prepare left side and
upright
Separate runners .
a: Push fit left runner
marked ‘L’ into the holes
shown on left side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
Fit hinge plates
making sure that the slot
is facing towards the
finished front edge.
Insert 2 large locking
nuts as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
b: Push fit right
runner marked ‘R’
into the holes shown on
upright .
Insert 2 large locking
nuts as shown.
1
M
E
2
E
M
R
F601
M
M
a:
b:
1
I
I
I
I
Step 5
G
G
G
A
A
Assembly Instructions
7
8
10mm
A
8
2
L
Fit plinth to the
upright
Attach plinth to the
upright using the
dowel already fitted and
secure with screw .
8
2
G
Fit base to the upright
Attach base to the
upright using 2 x
screws .
2
5
5
G
Finished front edge
2
Prepare plinth
Tap 2 wooden dowels
into the ends of the
plinth .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
8
Step 6
Step 7
Step 8
Assembly Instructions
8
G
G
G
Fit left side
Attach left side to the
base and plinth
using 3 x screws .
8
1
5
G
8
5
1
3
E
E
3
Prepare right side
Insert 2 large locking
nuts into the right
side .
E
Finished
front edge
Finished
front edge
G
G
Fit modesty
2 people are needed
here
Attach modesty to
the upright using 2 x
screws .
Support the modesty
until the right side has
been fitted in the next
stage.
7
2
G
7
2
Step 9
Step 10
Step 11
7
Assembly Instructions
9
L
Fit right side
2 people are needed
here
Attach right side to
the modesty using
2 x screws .
7
3
3
G
G
G
4
Prepare top panel
a: Screw 6 x metal
dowels into the holes
on the top .
Note: Tighten metal
dowels up fully against
the panel.
B
4
B
B
B
B
B
B
B
B
B
B
B
B
Step 12
Step 13
4
Assembly Instructions
10
B
E
Fit top
Push the 6 metal
dowels fitted to the
top down into the
holes in the top edge of
the side and upright
panels.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the side and upright
panels , and .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
1 32
E
B
E
4
1
2
3
4
x
y
y
y
13
L
K
x
13
13
Fit back panel
2 people are needed
here
Square up the unit by
making sure that
measurement x:x equals
y:y.
Place the back down
onto the unit, as shown.
Use the nail guide to
hold the nails
vertical and at the
correct distance whilst
you nail around the
outside of the back .
Note: Nails should
be spaced about 150mm
apart.
Stand the unit up.
Warning: The
desk is heavy.
Lift with care.
L
K
13
L
K
Step 14
Step 15
Assembly Instructions
11
L
C
1
2
6
x 4
Fit shelf studs
Insert 4 shelf studs ,
at the required height,
into the holes on the left
side and upright .
Slide the shelf in to
rest on top of the 4 shelf
studs.
C
21
Prepare door
Push fit the hinges
into the door .
Secure each hinge with
2 x screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the back edge of
the door.
J
N
12
N
J
J
N
N
J
J
12
90
12
Step 16
Step 17
6
H
H
Assembly Instructions
12
Fit door and handle
2 people are needed
here
Note: The easiest way to
attach the door is to
fit the top hinge first,
then align and fit the
bottom hinge.
a: Push the hinge
onto the front part of the
hinge plate .
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach the handle
to the door using 2 x
screw .
Note: Do not
overtighten screws .
N
N
N
I
I
I
N
I
D
H
H
12
D
e:
12
Step 18
a: b:
c: d:
I
N
I
I
B
I
N
N
N
A
N
I
B
Assembly Instructions
13
L
Step 19
b:
c:
d:
a:
Adjust the door if
needed
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, frontto-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Assembly Instructions
14
L
Insert drawer
Lift front of drawer whilst
inserting to overcome
the ‘stop’ system.
Note: To ensure that
your drawer runs
smoothly, spray a small
amount of furniture
polish into the grooves.
Assembly is complete
Warning: The
desk is heavy.
Lift with care.
Step 20
ALR2912
Loading...