Tolga - Storage Box
DR8252101
Assembly Instructions - Please keep for future reference
483/8364
Dimensions
Width - 73,4cm
Depth - 38,2cm
Height - 40,2cm
481/4113
487/7741
20kg
Tip : To prevent damage,
we recommend that you
483/8364 PINK
481/4113 BLUE
487/7741 OAK
build your unit on the
carton(s) it was packed in.
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 1 - 28/10/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Assembly should be carried out
by a competent adult only.
• do not use this item if any
components are missing
or damaged.
• this item is suitable for childeren
from the age of 6.
Glue safety - Take care when using glue, please follow the advice below•
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• From time to time check that
there are no loose screws on
this unit.
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
•
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
For damaged or missing parts, please visit:
Components - Panels
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Drawer Front 1
1
(688 x 370 x 18mm)
P4132
Drawer Back x 1
3
(634 x 250 x 15mm)
P6101
Plinth x 2
5
(694 x 92 x 15mm)
P7060
Top x 1
2
(734 x 382 x 18mm)
P5028
Drawer Base x 1
4
(634 x 305 x 15mm)
P6100
Right Drawer Side x 1
7
(323 x 250 x 15mm)
P6102
Side x 2
6
(384 x 380 x 18mm)
P2045
Left Drawer Side x 1
8
(323 x 250 x 15mm)
P6103
2
For damaged or missing parts, please visit:
Components - Fittings
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Locking screw x 12 (5x24mm)
D
Expando dowel x 8 (5x11mm)
Peg, brown x 1
FK1011
FK10561
FK1234
FK1012
15mm
Large locking nut x 12 (15x12mm)
FK1051
E
Expando housing x 8 (20x12mm)
FK1510
Glue x 2
FK1311
CB
Chipboardscrew x 10 (3x15mm)
FK1411
F
Wood dowel x 18 (8x30mm)
FK1244
IHG
Wheel x 5
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Spirit level
Setsquare
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
Small
hammer
0102030405060708090 100 110 120 130 140 150
0123456
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step - 1
Screw 24mm locking
screw A into side 6.
Note: look carreful for the
right postion.
Note: Insert 24mm locking
screw A as far as shown.
Do not over tighten.
Step - 2
Screw 24mm locking
screw A into side 6.
Note: look carreful for the
right postion.
Note: Insert 24mm locking
screw A as far as shown.
Do not over tighten.
Finished
front edge
A
A
A
A
A
6
6
A
A
A
A
A
A
A
A
A
A
A
A
6
A
A
A
A
A
A
6
6
6
A
Step - 3
Insert large locking nuts B
into Plinth 5.
Make sure the ‘arrow’ on
locking nuts B points
towards the hole in the
edge of 5.
Repeat this step on second
plinth 5.
2x
Finished
front edge
B
B
B
B
B
5
5
5
B
B
B
B
B
B
B
4
Assembly Instructions
Step - 4
Attaching panels
Position both side 6 onto
plinth 5 on both sides.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Step - 5
5
5
6
Finished
front edge
6
Put drop of glue H into the
6 holes of top 2.
Put dowels F into the
holes of top 2.
F
F
F
F
F
F
2
H
2
F
5
Assembly Instructions
Step - 6
Attaching top
Put drop of glue H into the
6 holes of side 6.
Position the 6 dowels H
of top 2 onto the 6 holes
of side 6.
2
5
6
5
Step - 7
Screw expando dowel B
Screw expando dowel D
into drawer back 3.
into drawer back 3.
Note: Insert expando
Note: Insert expando
dowel B as far as shown.
dowel D as far as shown.
Do not over tighten.
Do not over tighten.
6
H
2
3
D
6
D
D
6
Assembly Instructions
Step - 8
Screw expando dowel D
into left drawer side 8.
Note: Insert expando
dowel D as far as shown.
Do not over tighten.
Insert large locking nuts B
into left drawer side 8.
Make sure the ‘arrow’ on
locking nuts B points
towards the hole in the
edge of 8.
Put drop of glue H into the
2 holes of 8.
Put dowels F into the
holes of 8.
Step - 9
Screw expando dowel D
into right drawer side 7.
Note: Insert expando
dowel D as far as shown.
Do not over tighten.
Insert large locking nuts B
into right drawer side 7.
Make sure the ‘arrow’ on
locking nuts B points
towards the hole in the
edge of 7.
B
B
D
8
D
D
Finished
front edge
F
F
7
F
F
B
D
F
B
Finished
front edge
F
F
F
H
7
8
B
D
F
Put drop of glue H into the
2 holes of 8.
Put dowels F into the
holes of 7.
Step - 10
Screw expando dowel D
into drawer front 1.
Screw 24mm locking
screw A into front 1.
Note: Insert 24mm locking
screw A and expando
dowel D as far as shown.
Do not over tighten.
Put drop of glue H into the
4 holes of 1.
Put dowels F into the
holes of 1.
7
A
F
A
F
D
1
A
F
A
F
H
1
F
D
D
A
Assembly Instructions
Step - 11
Attaching drawer panels
Put drop of glue H into the
8 holes of drawer back 3.
Position the 4 dowels F
of drawer side 7 and 8
onto the holes of drawer
back 3.
Finished
edge
7
8
3
H
3
Step - 12
Insert expando housing E
into drawer base 4.
Make sure that the
expando housing E is
open.
Step - 13
Position the wheel I
on the drawer base 4.
Make sure that there is
enough free space to the
edges of drawer base 4.
E
E
E
E
C
C
I
309mm
C
C
4
E
C
C
C
I
4
130mm
E
E
E
E
C
I
C
C
I
use 2 chipboardscrews C
to mount each wheel I on
drawer base 4.
I
I
3mm
3mm
8
Assembly Instructions
Step - 14
Attaching drawer panels
Put drop of glue H into the
4 holes of drawer side 7
and 8.
3
Position the 4 dowels F
of drawer side 7 and 8
onto the holes of drawer
back 3.
Use a screwdriver to turn
locking nuts clockwise to
lock.
8
7
1
H
7
8
Step - 15
Attaching drawer base
slide drawer base 4
into the drawer from the
top until till the 8
expando dowels D are
totally in the expando
housing E of drawer base
4.
3
8
4
7
1
9
Assembly Instructions
Step - 16
Use a screwdriver to turn
expando housig clockwise
to lock.
3
Step - 17
Inserting Drawer
Slide the drawer into the
base.
7
1
2
4
Before adjusting the
storage box, use a spirit
level to check if the box
is level front-to-back
and side-to-side in the
three positions shown.
Use pegs G to square
the box. Knock peg G
in, as far as you require,
under the ends of the box
and then snap off flush
with the panel.
Assembly is complete.
6
8
G
G
If you need help or have damaged or missing parts, call the
Argos = 03456 400 800
3
1
!
Customer Helpline:
10
Assembly Instructions
11
Loading...