Argos Tolga - 22R ASSEMBLY INSTRUCTIONS

Tolga - 22R
DR8252041
Assembly Instructions - Please keep for future reference
323/6132
332/9489
338/8509
Dimensions
Width - 75cm
Height - 180cm
323/6132 BLUE 332/9489 PINK 338/8509 OAK
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928 For any other queries please contact the Customer Helpline on: 0345 640 2020
Issue 2 - 05/08/15
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the components and tools listed on the following pages.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• During assembly do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
power drill is set on a low torque setting. Warning: Only use a manual screwdriver to attach the hinges.
• Dispose of all packaging carefully and responsibly.
Glue safety - Take care when using glue, please follow the advice below•
Skin contact: Remove
contamination by washing with soap and water. This procedure should also be followed prior to eating and drinking.
Eye contact: Rinse immediately with clean water for 15 minutes and seek medical advice.
If swallowed: Seek medical advice immediately.
•To reduce the likelihood of damaging your product please ensure that your
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
Handy Hints
• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts
• From time to time check that there are no loose screws on this unit.
• Regularly check and ensure that all bolts and fi ttings are tightend properly.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
For damaged or missing parts, please visit:
Components - Panels
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Left Side x 1
1
(1800 x 497 x 15mm)
P2053
Door x 2
4
(1242 x 372 x 18mm)
P3068
Right Side x 1
2
(1800 x 497 x 15mm)
P2044
Top x 1
5
(720 x 496 x 18mm)
P1488
Shelf x 2
6
(720 x 496 x 18mm)
P1487
Back x 1
3
(1754 x 746 x 2.5mm)
BO2553
Drawer Front x 2
7
(747 x 247 x 18mm)
P4139
Drawer Base x 2
8
(681 x 343 x 2.5mm)
BO2540
Plinth x 2
9
(720 x 70 x 15mm)
P7058
Left Drawer Side x 2
10
(350 x 140 x 12,5mm)
LA1614
Drawer Back x 2
11
(670 x 140 x12.5mm)
LA1617
Right Drawer Side x 2
12
(350 x 140 x 12,5mm)
LA1615
2
For damaged or missing parts, please visit:
Components - Fittings
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Locking screw x 26 (5x24mm)
D
12.5mm Pozi screw x 42
FK1515
Nail x 60
FK1235
L-Bracket x 1
FK1415
Nail holder x 1
P
FK1011
FK1309
PM1515 RA
FK1010
12mm
Locking nut x 4 (12x10mm)
FK1301
E
10mm Fixing screw drawer x 8
FK1410
Wood dowel x 4 (5x30mm)
FK1234
KJ
Peg, brown x 1
PM1515 LA
NM
Runner left part A x 2
PM1515 RB
Q
FK1012
CB
15mm
Large locking nut x 22 (15x12mm)
FK1400
F
Screw x 7 (4x15mm)
FK1250
IHG
Drawer base support x 12
FA1510
L
Glue x 2
PM1515 LB
O
Runner left part B x 2
FK1223
R
Runner right part A x 2
PM1829
S
Hanger rail large x 1 (712mm)
ZF99936
V
Wall plug (6mm) and parkerscrew x 1
Tools required
Phillips screwdriver (medium & large)
Flatblade screwdriver (medium)
7mm Suitable drill bit (for use with wall plug)
Runner right part B x 2
T
Hinge back x 6
FK1262
Drill
Spirit level
Setsquare
Hanger rail support x 2
U
Hinge door x 6
0102030405060708090 100 110 120 130 140 150
0123456
Eye protection (when using a hammer or glue)
FK1263
Small hammer
Ruler/tape measure
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
The screws length is measured from the head to the point (30mm screw shown).
3
105
110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step - 1
Insert large locking nuts C into plinth 9.
Make sure the ‘arrow’ on locking nuts C points towards the hole in the edge of 9.
Put drop of glue L into the 2 holes of plinth 9.
Put dowels F into the holes of plinth 9.
Do this step twice
Step - 2
Attaching runners a: Fix runner right part A P
on right side 2 as shown usesing 10mm fixing screw drawer E into right side 2.
Note: look carreful for the right postion.
Screw 24mm locking screw A into right side 2.
2x
a:
A
C
H
9
C
L
H
A
A
E
E
P
A
P
E
E
2
A
H
A
D
R
Finished front edge
C
A
A
A
A
A
Note: Insert 24mm locking screw A as far as shown.
Do not over tighten.
Attach hanger rail support R using 12.5mm pozi screw D onto right side
2.
Insert 12,5mm pozi
b:
screw D as shown into right side the 2 to fix runner right part A P.
Screw hinge back T onto right side 2.
b:
A
P
D
P
D
D
D
Warning: Do not use an electric screwdriver to attach the hinges as this can weaken the fixing.
E E
P
2
T
D
D
DD D
T
Finished front edge
T
4
Loading...
+ 11 hidden pages