MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference
417/9865
Issue 1 - 08/07/15
Taylor - 4+1 Sideboard
Width - 99.5cm
Depth - 39.5cm
Height - 71.5cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 31kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
1 2 3
4
Left End (DF2882B)
(563 x 392mm)
Top (DF2880)
(995 x 394mm)
Shelf (DF2886)
(447 x 373mm)
Right End (DF2883)
(563 x 392mm)
Divider (DF2884B)
(563 x 375mm)
Base (DF2881)
(995 x 394mm)
Drawer Front (DF2885)
(495 x 137mm) x 4
Drawer Back (W447-95)
(447 x 95mm) x 4
Left Drawer Side (W350-95LH)
(350 x 95mm) x 4
Drawer Base (T458-347)
(458 x 347mm) x 4
Back (X987 x 589)
(987 x 589mm)
Right Drawer Side (W350-95RH)
(350 x 95mm) x 4
5
6
7 9
108
11
Door (DF2887)
(557 x 457mm)
12
13
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
M
C
Metal dowel (F901) x 14
Wooden dowel (F22) x 12
Small locking
nut (F3) x 8
Large locking
nut (F900) x 6
40mm Screw (F910) x 6
R
R Runner (F160) x 4
b
L Runner (F161) x 4
R
c
L Runner (F159) x 4
R
a
R Runner (F162) x 4
R
d
350mm long
J
13mm Screw (F63) x 28
Knock-in Peg (F171GY) x 16
K
Wedgefix (F639) x 8
13mm Screw (F79) x 16
L
S
O
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
P Q
Hinge (F518) x 2
Hinge plate
(F523) x 2
T
Leg Bracket
(F333) x 4
Shelf stud (F110) x 4
25mm Screw (F50) x 1
N
Handle (F415OAK) x 1
Leg (F343OAK) x 4
9mm Screw (F73) x 24
Bag of Nails
(F51) x 1
7
Assembly Instructions
4
Step 1
x 4
x 4 x 4
A
B
A
B
B
B
B
9
10
Step 2
Prepare the 4 drawer
fronts
Screw 2 metal dowels
into each of the 4 drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
9
10
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
7
B
B
9
10
9
10
A
A
7
7
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
11
9 10
7
8
9 10
11
8
8
J
9 10
Step 6
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
J
J
K
K
K
11
9
8
9
10
11
10
x 4
x 4
x 4
Assembly Instructions
6
Step 7
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
10
R c
9
7
G
R d
x 4
G
G
G
G
R c
R d
Runners must be
pushed up against
the drawer front
10
9
7
D
D
Prepare the right end
Tap 4 wooden dowels
into the right end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the right end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
C
C
P
P
P
C
2
P
2
D
D
D
2
2
Finished
front edge
Step 8
C
10mm
D
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 10
C
A
Fit the right end to
the top
Push the right end
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right end .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
2
C
C
2
Prepare the top
Screw 6 metal dowels
into the top .
A
4
A
A
A
A
A
A
4
Finished
front edge
2
4
Assembly Instructions
Step 11
8
Finished front edge
Finished front edge
D
D
Finished front edge
a:
Prepare the left end
a: Fit 4 runners to
the left end .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
c: Tap 4 wooden
dowels into the left
end .
Insert 2 large locking
nuts into the left end
. .
b:
D
C
1
1
R a
1
I
I
c:
Finished front edge
R a
Finished front edge
G
G
R a
I
R a
I
I
I
R a
I
I
I
R a
I
I
I
R a
I
I
G
G
G
G
C
C
D
D
1
1
1
R a
I I
1st
screw
2nd
screw
I
3rd
screw
Assembly Instructions
9
Step 12
D
D
Finished
front edge
Fit the left end to the
top
Push the left end
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left end .
4
1
C
1
1
4
Step 13
a:
b:
Prepare the divider
a: Fit 4 runners to
the divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Tap 4 wooden dowels
into the divider .
Insert 2 large locking
nuts into the divider
. .
C
3
R b
3
I
I
G
R b
R b
Finished front edge
G
I
I
R b
I
I
I
R b
I
I
I
R b
I
I
I
R b
I
Finished
front edge
G
G
G
G
C
C
D
D
D
3
3
3
R b
II
1st
screw
2nd
screw
I
3rd
screw
Finished front edge
Assembly Instructions
Step 14
10
Step 15
Finished
front edge
Polystyrene
block
Fit the divider
Push the divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Note: Place a
polystyrene block from
the packaging
underneath the divider to
raise it up level with the
ends.
4
3
C
3
3
4
Fit the base
Fit the base onto the
left end , right end
and the divider using 6
screws .
5
1 2
3
E
E
E
E
E
E
E
5
1
2
3
Assembly Instructions
11
Step 16
yy
yy
xx
Step 17
5
Note: The raised part
of the leg bracket must
point towards the
centre of the panel.
Fit the leg brackets to
the base
a: Screw each leg
bracket . to the base
using 2 screws into
the mark holes.
b: Then use another 2
screws into the other
2 holes.
5
S
H
H
S
H
H
S
S
S
S
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
13
L
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
13
xx
b:
L
13
Assembly Instructions
Step 18
12
Step 19
Fit the legs
Screw the legs into
the leg brackets .
Carefully stand the
unit up for the next
step.
T
S
T
T
Warning: The
unit is heavy.
Lift with care.
T
T
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Side
panel
Drawer
Assembly Instructions
13
Step 20
Fit the shelves
Insert 4 shelf studs at
the required height.
Lower the shelf down
onto the shelf studs .
M
x 4
M
6
M
6
Step 21
Prepare the door
Push fit 2 hinges into
the door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
G
Q
12
90
Q
Q
G
G
Q
G
G
12
Assembly Instructions
Step 22
14
Fit the door and handle
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the
hinge from the
hinge plate
and then
re-assemble
being careful
to follow
instructions
a-c.
e: Attach the
handle to
the door
using screw .
Q
Q
Q
P
P
P
Q
P
N
F
12
e:
a: b:
c: d:
P
Q
P
P
B
P
Q
Q
Q
A
Q
P
B
Note: The easiest way to attach
the door is to fit the top hinge first,
then align and fit the other hinge.
12
N
F
Assembly Instructions
15
Step 23
Adjust the door if
needed
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, frontto-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
a:
A
A
B
C
b:
c:
d:
Assembly Instructions
16
Step 24
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Fit the overbalance
protector kit
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
O
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
O
O
Example
Screw
(not supplied)
Washer
Screw
UNIT
ALR3160
Loading...