Argos Stowe - 3 Drawer Chest ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

Important - Please read these instructions fully before starting assembly

Stowe - 3 Drawer Chest

Assembly Instructions - Please keep for future reference

404/1560

427/3871

Issue 1 - 03/07/15

Width - 70.6cm

Depth - 39.4cm

Height - 76.3cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 24kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 1, 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.

• Dispose of all packaging
carefully and responsibly.

Tools required

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Electric drill
(do not use for
fitting screws)

Components - Panels

Please check you have all the panels listed below

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

2

1

2

Left Drawer Side (W330-124LH)

(33 x 12.4cm) x 3

Right Drawer Side (W330-124RH)

(33 x 12.4cm) x 3

8

9 10

11

12

3

Top (DF2403)

(70.8 x 39.4cm)

5

Side Plinth (DF2386)

(37.4 x 9.1cm) x 2

6

Front Plinth (DF2408)

(70.8 x 9.2cm)

7

Drawer Front (DF2407)

(64 x 19.2cm) x 3

4

Rail (DF2406)

(64.6 x 9.2cm) x 5

Drawer Back (W613-124)

(61.3 x 12.4cm) x 3

Drawer Base (T624-327)

(62.4 x 32.7cm) x 3

Left Side (DF2404)

(74.6 x 37.4cm)

Right Side (DF2405)

(74.6 x 37.4cm)

Back (X672-667)

(67.2 x 66.7cm)

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Components - Fittings

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020

3

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A B

D F

G H I

L

Small locking
nut (F3) x 6

C

M

J K

Drawer runner (F1004) x 6

Large locking
nut (F900) x 16

Metal dowel (F901) x 22

Wooden dowel (F22) x 16

Wedgefix (F639) x 12

25mm Screw (F50) x 4

O

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

19mm Screw (F461) x 6

9mm Screw (F74) x 6

9mm Screw (F73) x 12

Plastic Nail (F91) x 4

E

N

OR

Oak Handle
(F463) x 6

White Handle
(F565) x 6

N

38mm Screw (F81) x 6

P

Knock-in Peg (F171GY) x 12

Bag of Nails

(F51) x 1

7

Assembly Instructions

4

Step 1

x 3

x 3

x 3

x 3

A

B

A

C

C

C

C

8

9

Step 2

Prepare the 3 drawer
fronts

Screw 2 metal dowels
into each of the drawer
fronts .

Note: Tighten the metal
dowels up fully against
the panels.

A

7

Prepare the drawer
sides

Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .

Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.

Step 3

C

8

9

Attach the drawer
sides to the drawer
fronts

Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .

Turn the small locking
nuts on the left
drawer side and right
drawer side .

Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.

8
9

7

C

C

8
9

A

7

8

9

A