Sophia Dressing Table,Stool and Mirror
-Table & Mirror
Assembly Instructions - Please keep for future reference
471/9160
457/7656
501/2921
Dimensions
Width - 80cm
Depth - 38.5cm
Height - 141.3cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts,call the Customer Helpline:03456 400800.
For further assistance please visit http://www.argos-support.co.uk/.
Issue 1 - 02/12/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
·Check you have all the
components and tools listed on
pages 2 and 3.
·Remove all fittings from the
plastic bags and separate them
into their groups.
·Keep children and animals
away from the work area, small
parts could choke if swallowed.
·Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
·Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
·Do not stand or put weight on
the product, this could cause
damage.
·Assemble the item as close to
its final position (in the same
room) as possible.
·Assemble on a soft level
surface to avoid damaging the
unit or your floor.
·Parts of the assembly will be
easier with 2 people.
·From time to time check that
there are no loose screws on
this unit.
·To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torgue
setting.
·This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
·Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
·Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
If you have damaged or missing componets, call the
Components - Panels
Customer Helpline:03456 400800.For further
assistance please visit http://www.argos-support.co.uk/
Please check you have all the panels listed below
Side, left ×1
Top ×1
1
(80× 38.5cm)
2
(34.6× 12.6cm)
Side, right ×1
3
(34.6× 12.6cm)
Drawer front ×1
4 5
(65× 11.8cm)
Drawer back ×1
7
(60.5× 9.2cm)
Base fram ×1
10
(79× 37.5cm)
8
Drawer bottom ×1
(61.6× 29.9cm)
11
12
6
9
Back panel ×1
(66.5× 13.7cm)
Leg ×4
(66.3× 5.6cm)
Drawer side, right ×1
(30× 9.5cm)
Drawer support rail ×1
(28.8× 5.7cm)
Mirror ×1
13
(55 × 35cm)
Mirror post x 2
14 15
(31.5 × 14.5cm)
Mirror base ×1
(70× 13.5cm)
2
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Ø6×35mm Screw × 14
B
Ø6×20mm Washer × 8
ED
Allen Key × 1
G
Ø8×30mm Wooden dowel × 10
300mm Runner, outside left × 1
H
Ø6×33.5/11mm
Large locking pin × 8
Handle × 2
300mm Runner, inside left × 1
M N O
Ø3.5×15mm Screw × 14
C
Washer × 8
F
I
Screw × 2
LJ K
300mm Runner, outside right ×1
Ø6×20/11mm
Small locking pin × 5
P
Q
Ø3.5×25mm Screw × 6
S
Ø6×18mm Washer × 2
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Ruler - Use this ruler to help correctly identify the screws
R
Ø6×30mm Screw × 2
Rubber
mallet
0 101520253035404550556065707580859095100
5
3
105
110115120125130135140145150155160165170
Assembly Instructions
Step 1
12
10
A
B
C
D
12
Step 2
Repeat Step 1 to
assemble the rest 3 legs.
B
C
A
D
B
A
10
B
12
A
C
A
10
4
Assembly Instructions
Step 3
a: Insert Wooden dowel
to the Sides and
G
.
3
2
b: Insert Large locking
E
Pin into Base frame
.
10
Note: Insert locking pin
as shown.
G
a:
2
G
G
3
G
G
G
G
E
10
G
G
E
E
E
Do not over tighten.
Step 4
Attach Left Side to
the Base frame, insert
Large locking Nut into
Left sides , use screw
2
driver to turn Locking nut
clockwise to lock.
2
F
b:
2
1 2 3
E
F
F
10
F
5
Assembly Instructions
Step 5
Fix Runner outside left
to Left Side by
Screws .
2
N
J
N
N N
2
J
N
J
N
Step 6
Repeat Step 4 to Right
Side .
3
3
F
F
6
Assembly Instructions
Step 7
Repeat Step 5 to fix
Runner outside right to
Right Side .
L
N
N N
L
N
3
L
N
Step 8
Slip the Back panel
to the groves on the
Sides.
11
11
7
Assembly Instructions
Step 9
Insert Large locking Pin
into Top panel .
1
Note: Insert locking pin
as shown.
Do not over tighten.
E
E
E
E
E
1
E
Step 10
Attach Top panel to
the unit.
Insert Large locking nut
as show on picture and
use screw driver to trun
Large locking nut
clockwise to lock.
1
1
F
F
11
F
2
3
8
Assembly Instructions
Step 11
Assembling the drawer.
a: Insert 5 Small locking
O
pin into holes shown
on back of Drawer front
.
4
Note: Insert Locking pin
as far as shown.
Do not over tighten.
b: Fix Drawer sides
6
and and Drawer
support rail to Drawer
front .
4
Insert Small locking nuts
into Drawers Sides and
Drawer support rail.
Use a screwdriver to turn
locking nuts clockwise
P
to lock.
c: Slip Drawer base
into grooves on the
Drawer walls.
5
9
8
O
O
O
a:
O
O
4
6
9
P
5
1
O
2
P
3
b:
P
P
P
4
8
c:
Q
7
P
Q
Q
O
Q
d: Fix Drawer back
7
onto sides by using 6
Screws .
Q
e: Fix Runner inside left
and Runer inside right
onto the underside of
Drawer sides by using 6
Screws .
F: Fix Handle by
using Screw .
N
H
I
M
Q
Q
d:
K
N
K
N
N
N
N
N
M
e:
I
f:
I
H
H
Assembly Instructions
Step 12
Inserting the drawer
carefully.
10
Assembly Instructions
Step 13
a. Insert Wooden dowels
G
into Mirror post as
14
show on picture.
b. Attach Mirror post to
the Mirror by Screw
and Washer .
14
S
c. Attach Mirror post to
Mirror base by Screw
A
.
15
G
× 2
a:
A
A
S
14
G
S
A
b:
S
A
14
D
14
13
c:
15
A
A
A
A
D
11
Assembly Instructions
Step 14
Put the mirror unit on the
dressing table top panel
and fix with Screw .
R
R
R
Assembly is complete.
If you need help or have damaged or missing parts,call the Customer Helpline:03456 400800.
For further assistance please visit http://www.argos-support.co.uk/
12
Loading...