Sideboard
Assembly Instructions - Please keep for future reference
041 xx 5500
Dimensions
Width - 116cm
Depth - 39cm
Height - 73cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Rev A - 31.03.15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 4.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Do Not dispose of packaging
until assembly complete.
Dispose of all packaging
carefully and responsibly
when assembly complete.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
From time to time check that
there are no loose screws on
this unit.
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergants, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
1
Components - Panels
Please check you have all the panels listed below
Important - Thick lines indicate finished edges
Left hand division (65x35cm)
Code -
Top (116x39cm)
Code -
Bottom (116x39cm)
Code -
7498
7500
7501
Right hand division (65x35cm)
Code -
7499
Rail x 4 (65x18.8cm)
Code -
Shelf (77.8x33cm)
Code -
Shelf x 4 (35x17cm)
Code -
7502
7503
7504
Door x 2 (48.4x38.4cm)
Code -
7010
Drawer front (77.2x15.7cm)
Code -
Drawer bottom (75.6x29.8cm)
Code -
7505
7019
Left drawer side (30x10cm)
Code -
622xx7002
Drawer back
Code -
624xx7007
(74.5x10cm)
Backpanel (78.8x65cm)
Code -
7506
Right drawer side
Code -
(30x10cm)
623xx7002
2
Components - Exploded View
Important - Thick lines indicate finished edges
7502
7502
7504
7504
7010
7498
7010
7503
7398
7500
7506
7502
7499
7504
7504
3
622xx7002
624xx7007
7019
7505
623xx7002
7501
7502
If you have damaged or missing components, call the
Components-Fittings
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
A
Large cam x 32 - Code 760001103
D
12mm screw x 14 - Code 690001008
I
9mm bolt x 2 - Code 690001078
L
45mm screw x 12 - Code 690001075
O
Fully cranked 26mm
hinge x 4
Code 652001120
B
Metal dowel x 34 - Code 760003004
E
Tube of glue x 1 - Code 680001037
J
Handle x 3
Code 644396000
M
22mm screw x 16- Code 690001018
Hingeplate x 4
P
Code 653006000
C
Small cam x 2 - Code 760003005
H
Runner x 2 - Code 760001040
K
N
Square foot x 5
Code 720396000
Wooden dowel x 8
Code 770001006
Tools required
Cross headed screwdriver
(small & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Ruler - Use this ruler to help correctly identify the screws
0
mm
10
20
30
40
50
60
70
80
90
100
110
120
130
Bradawl
140
150
160
170
4
Assembly Instructions
Step 1
Fitting dowels to top
panel
B
Note: Insert metal
dowels as far as
B
shown by arrows.
Do not over tighten.
Step 2
Fitting cams to
shelves
A
Note: Ensure cam
arrow points towards
the edge with hole.
Fittings you will need for this step:
B
(x12)
B
B
B
B
B
B
Fittings you will need for this step:
A
Large
A
(x20)
A
A
7503
7500
A
B
A
B
B
A
B
B
B
A
A
7504 x4
Step 3
Fitting cams and
dowels to left, right
divisions and rails
A
Note: Ensure cam
arrow points towards
the edge with hole.
B
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Fittings you will need for this step:
A
A
Large
(x12)
B
(x20)
B
B
7498
A
A
B
B
B
7502 x4
A
B
B
7499
A
A
B
5
Assembly Instructions
Step 4
Fitting hingeplates
to left hand division
Step 5
Fitting hingeplates
to right hand division
Fittings you will need for this step:
P
(x2)
7498
P
Fittings you will need for this step:
P
(x2)
P
P
Notch in Hingeplate points
towards edge.
Step 6
Fitting wooden
dowels to left, right
hand divisions
P
Notch in Hingeplate points
towards edge.
Fittings you will need for this step:
N
7502 x4
(x8)
N
N
P
P
7499
N
Use a hammer to
knock in wooden dowels
N
into inner holes.
N
B
N
N
7499
7498
6
Assembly Instructions
Step 7
Attaching runners
a: Align the drawer
runner with the
edge of panel ,
the 2nd hole from
the front will then line up
with a pre-drilled hole,
secure the runner to the
panel using screws .
H
7498
D
Fittings you will need for this step:
H
(x1)
D
(x3)
a:
H
7498
D
H
Note:
Please note
runner sits
flush with
edge.
Note:
Ensure these
holes are
positioned as shown.
D
b: Slide the drawer
runner forward to
secure 2 screws .
The 2nd to last and
middle hole in the
runner will line up with
the pre-drilled holes in
the panel.
H
D
D
b:
D
2ND
Middle
7498
D
H
H
7
Assembly Instructions
Step 8
Attaching runners
a: Align the drawer
runner with the
edge of panel ,
the 2nd hole from
the front will then line up
with a pre-drilled hole,
secure the runner to the
panel using screws .
H
7499
D
Fittings you will need for this step:
H
(x1)
D
(x3)
D
7499
H
a:
D
Note:
Ensure these
holes are
positioned as
shown.
b: Slide the drawer
runner forward to
secure 2 screws .
The 2nd to last and
middle hole in the runner
will line up with the
pre-drilled holes in the
panel.
H
D
H
D
D
7499
Note:
Please note
runner sits
flush with
edge.
b:
D
Middle
H
2ND
D
H
8
Assembly Instructions
Step 9
Attach hinges and
handles to doors
Important:
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
90
O
98
O
O
Fittings you will need for this step:
O
(x4)
D
(x8)
M
(x4)
O
a:
7010x2
b:
J
(x2)
O
O
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
c: Secure hinges to
doors using
screws .
O
Bradawl
O
O
7010
D
D
D
O
D
O
O
D
7010x2
c:
7010x2
d:
D
D
O
M
M
d: Secure handle to
doors using
screws .
9
7010
M
J
7010x2
J
Assembly Instructions
Step 10
Drawer assembly
B
a: Insert dowels into
drawer fronts .
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
7505
B
C
Fittings you will need for this step:
B
(x2)
B
Fittings you will need for this step:
C
Small
a:
b:
(x2)
B
7505
Right hand side
623xx7002
b: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
622xx7002
623xx7002
C
c: Insert wooden dowels
in drawer back
into holes in
624xx7007
left
622xx7002
right hand
623xx7002
drawer sides.
Left hand side
622xx7002
Left hand side
622xx7002
c:
C
C
Drawer Back
624xx7007
Continued on next page.
Right hand side
623xx7002
10
Assembly Instructions
Step 10 - Continued
Drawer assembly
Continued...
d: Using glue put a
few drops into grooves in
drawer sides and back.
Slide drawer bottom
7019
into grooves in
left,right drawer sides
and drawer back.
Ensure foil on the
drawer bottom is facing
upwards.
e: Insert cams already
inserted in left and right
drawer sides onto
dowels in drawer
front .
B
7505
E
C
Fittings you will need for this step:
E
(x1)
7019
FOIL FACE
e:
d:
C
Turn cam 180 degrees
to lock
f: Secure handles to
drawer front
using screws .
Important:
Please allow 40 minutes
for the glue to set before
using the drawer.
7505
J
M
7505
Fittings you will need for this step:
M
(x2)
J
(x1)
7505
f:
M
M
11
J
Assembly Instructions
Step 11
Attach left and right
hand divisions to
shelf
Locate cams in shelf
onto dowels in
7503
left and right
7498
hand divisions.
Then lock.
Turn cam 180 degrees
to lock
A
B
7499
A
7499
7503
7498
Step 12
Attach left and right
hand divisions to top
panel
B
A
7499
7500
A
Locate cams in left
and right
7498
hand divisions onto
dowels in top .
Then lock.
Turn cam 180 degrees
to lock
7498
7499
7500
12
Assembly Instructions
Step 13
Locate shelves to
rails
Locate cams in shelves
onto dowels
7504
in rails .
7502
A
B
Then lock.
Ensure cam holes to
top.
7504
7502
A
Turn cam 180 degrees
to lock
Step 14
Attach rails to top
panel
Locate cams in panels
onto dowels
7502
in top panel .
Then lock.
A
B
7500
7502
7504
7502
7504
7504
7502
7502
7502
Turn cam 180 degrees
to lock
13
A
7502
Finished edge
4755
6086
7502
7500
Assembly Instructions
Step 15
Locate backpanels
into grooves in left
and right hand end
divisions
7506
Locate backpanel
7506
into grooves in left hand
7498
and right hand
7499
slide the
backpanel all the
7506
way down to the top
panel.
Step 16
Attach bottom to rails
and divisions
Locate wooden dowels
N
already inserted in
divisions and
and rails into holes
7498
7502
in bottom panel .
Now locate screw
through holes in bottom
panel and screw
7501
into holes in divisions
7498
. , and rails
7502
.
7499
7499
7501
L
FOIL FACE
7499
4755
6086
Fittings you will need for this step:
L
Raw face
(x12)
L
L
L
7501
L
L
L
7498
L
L
7498
L
L
7502
L
L
7502
L
7502
7499
4755
6086
7502
14
Assembly Instructions
Step 17
Attach feet
To locate feet to the
bottom you will
need to mark position
with a bradawl 15mm
and 38mm in as shown,
then screw the foot into
place.
Repeat in each corner.
Attach the 5th foot
centrally.
7501
Fittings you will need for this step:
M
(x10)
PLEASE NOTE: BOTTOM PANEL
EDGED IN SILVER.
K
(x5)
M
M
M
Bradawl
4755
6086
38mm
38mm
15mm
15mm
M
7501
M
M
M
M
M
M
Step 18
Lift unit onto its feet
then locate drawer
Warning:
2 people to lift.
Lift with care.
For this step we
recommend you follow
the helpful hints page
on page 16.
Fittings you will need for this step:
I
(x2)
I
I
15
I
2nd HOLE
Assembly Instructions
Step 18 continued
Locate drawers helpful
hints
a: Pull sliding part of
drawer runners out
so they are fully
extended.
H
b: Locate drawer onto
runners.
c: Locate screwdriver
into second threaded
L
hole in drawer runner .
H
d: Keeping screwdriver
in place push the drawer
in until the screwdriver
pushes against the
panel.
Remove the screwdriver.
A
C
B
H
L
L
H
D
J
H
L
2nd Hole
e/f: Pull drawer out slowly
and line the front hole in the
drawer side with the 2nd
threaded hole in runner .
Holding runner and
drawer side together
insert bolts through the
drawer side and
into threaded hole in
runner .
Now repeat these
steps for the other
side of the drawer.
I
J
L
H
H
E
F
H
I
J
2nd Hole
16
Assembly Instructions
Step 19
Hanging doors
a: With help, slot door
hinges onto hinge
plates .
Ensure screw on hinge
O
slides into the slot
on hingeplate .
See Diagrams 1,2 and 3.
O
P
P
b: Tighten screw shown
to lock hinges in
position.
Repeat a and b for
opposite door.
See ‘Hinge adjustment’
in step 20 if the doors
need adjusting.
7010
O
O
P
P
Diagram 1
a:
O
b:
O
Underside view
P
P
Diagram 2
Diagram 3
B
Ensure the underside of screw
B slides into slot on hingeplate.
B
Hinge correctly attached to
hingeplate.
B
17
Hinge incorrectly attached to
hingeplate.
Assembly Instructions
Step 20
Hinge adjustment
a:
a: To move doors up
or down: loosen screws
shown and move doors
to suit.
Re-tighten screws.
b: To move doors in or
out: loosen screw
shown and move doors
to suit.
Re-tighten screws.
P
O
b:
P
c: To move doors left
or right: loosen or
tighten screw as shown
Be careful not to fully
unscrew.
O
c:
P
O
Congratulations!
Your unit is complete
18
Important Information
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Simply contact us on CUSTOMER HELPLINE : 01709 534123 Between 8am - 4.30pm
Monday to Thursday and 8am - 2.30p.m friday. Your statutory rights are not affected.
Please have the following information: Unit Description, Product Code, Product Colour,
Place of Purchase, Catalogue Ref. No., Item Code, and have the assembly instructions close
to hand.
We do have an answer machine should you contact us out of office hours, so in addition to
the above information could you leave your name, address, daytime telephone number and
the nature of your call on the answerphone. All calls will be actioned asap.
You can also e-mail your requests to us at: customer.helpdesk@addspacefl.co.uk
Alternatively Write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.
19
Loading...