Argos Range Kitchen - Under Oven Cabinet ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 60cm

Depth - 59cm

Height - 87cm

Range Kitchen - Under Oven Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 16/02/11

Important - Please read these instructions fully before starting assembly

656/5831

hygena

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 16.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2, 3 and 4.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

2

4

3

Left Side (DPF068A)

(720 x 560mm)

Right Side (DPF069A)

(720 x 560mm)

Base (DPF078A)

(569 x 494mm)

Cross Rail (DPF080A)

(569 x 96mm) x 2

5

Support Rail (DPF112A)

(495 x 105mm) x 4

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Tools required

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 8

C

D

Large locking nut (F900) x 8

G H

K

I a

I c

I d

I e

I b

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

J

Electric drill

E

13mm Screw (F79) x 14

Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2

Bracket (F945) x 8

Leg Bracket (F127) x 2

Leg Socket (F120) x 4

Leg Clip (F128) x 2

16mm Screw (F129) x 16

Leg (F122) x 4

45mm Screw (F65) x 4

F

25mm Screw (F50) x 2

38mm Screw (F933) x 4

Please check you have all the fittings listed below

4

Components - Fascia

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Please see below for the correct fascia code for this unit in your chosen fascia design.

Monza Oak

Monza Beech

Imola Black Gloss

Imola Cream Gloss

Imola White Gloss

Pesaro Cream

Pesaro Oak

Ricadi

656/6713

656/6706

656/6720

656/6744

656/6737

656/6768

656/6751

656/6775

Appliance Fascias are supplied seperately

The front surface of this fascia

is protected with a peel-off film

Monza Appliance Fascia (DPF124A)

(596 x 120mm)

6

Imola Appliance Fascia (DPF124A)

(596 x 120mm)

6

Ricadi Appliance Fascia (DPF124A)

(596 x 120mm)

6

Pesaro Appliance Fascia (DPF124A)

(596 x 120mm)

6

Assembly Instructions

5

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

B

J

E

1

B

J

E

5mm

150mm

B

Only screw a metal dowel into one

of these holes (refer to step 1).

1st 5mm hole

2nd 5mm hole

1

Prepare the left side

Screw a metal dowel into one of the holes shown on the left side . .

Note: Tighten metal dowels up fully against the panels.

Important: The position of the metal dowel depends on where you would like the cross rail to be.

B

1

B

The hole chosen for the metal dowel determines the position of the cross rail. This will depend on where the services to the oven will be located.

We recommend that you consult a qualified joiner or kitchen fitter.

Step 2

Prepare the left side

Screw 3 metal dowels into the holes shown on the left side .

Note: Tighten metal dowels up fully against the panels.

Fit a bracket flush to the top edge of the left side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the left side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

Note: The brackets must be flush with the top/back edge of the panel.

B

1

J

1

J

1

E

J

E

Assembly Instructions

6

Step 3

Step 4

Prepare the right side

Screw 3 metal dowels into the holes shown on the right side .

Fit a bracket flush to the top edge of the right side , about 150mm in from the groove, see diagram.

Secure the bracket using screw .

Fit another bracket flush to the back edge of the right side , about 5mm down from the top edge, see diagram.

Secure the bracket using screw .

B

2

J

2

J

2

E

J

E

J

E

B

J

2

J

E

Prepare the right side

Screw a metal dowel into one of the holes shown on the right side . .

Use the same hole that you used in step 1.

Only screw a metal dowel

into one of these holes (use

the same hole as step 1).

B

2

Assembly Instructions

7

Step 5

Step 6

I a

I b

b: c: d:

Fit the legs to the base

a: Push the leg sockets

. into the holes in the base as shown.

b: Secure each leg

socket with 3 screws .

c: Tap in the centre plug

on each leg socket .

d: Push the leg into

the leg socket .

I a

I e

3

x 3

I a

I b

I a

3

A

Prepare the base

Insert 4 large locking nuts into the base as shown.

Note: Arrow on locking nut must point towards hole in edge of panel.

Tap 6 wooden dowels into the base as shown.

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

C

3

10mm

A

3

A

C

A

3

Assembly Instructions

8

Step 7

4

Fit the 2 cross rails

Push each cross rail onto the right side .

Use a screwdriver to tighten the large locking nut fitted to each cross rail .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

2

C

4

2

4

Support this cross rail until the left side has been fitted in the next step.

Finished

front edge

Step 8

A

C

Prepare the 2 cross rails

Insert 2 large locking nuts into the cross rails as shown.

Tap 2 wooden dowels into the cross rails as shown.

Step 9

4

A

Join the right side and base

Push the base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

B

F

3

2

C

2

3

A

C

4

Assembly Instructions

9

Step 10

Step 11

Fit 2 support rails

Fit a support rail to the right side using 2 screws .

Fit a support rail to the left side using 2 screws .

Note: The support rails must be flush with the front of the unit.

Step 12

Prepare the other 2 support rails

Fit 2 brackets flush to one end of the remaing support rails using screw .

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the large locking nut fitted to the 2 cross rails and the 2 fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

3

1

C

4

1

4

3

1

2

K

5

1

2

K

5

K

J

E

5

J

E

5

E