Argos Range Kitchen - Corner Wall Cabinet ASSEMBLY INSTRUCTIONS

Range Kitchen - Corner Wall Cabinet

Assembly Instructions - Please keep for future reference

hygena

Monza

656/5752

Ricadi

Pesaro

Imola

Dimensions

Width - 57cm

Depth - 57cm

MADE IN

Height - 72cm

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

BRITAIN

Issue 1 - 03/09/10

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 16kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 to 5.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

Care and maintenance

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).

• Dispose of all packaging
carefully and responsibly.

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

If you have damaged or missing components, call the

Components - Panels

Customer Helpline: 08456 400800 quoting the reference

numbers below

Please check you have all the panels listed below

1

Top/Base (DPF101A)

(566 x 566mm) x 2

4

End Panel (DPF141A)

(320 x 716 mm) x 2

2 3

Loose Shelf (DPF102A)

(545 x 545mm)

5 6

Left Back Panel (DPF104A)

(430 x 694 mm)

Back (DPF103A)

(205 x 684mm)

Right Back Panel (DPF105A)

(430 x 694 mm)

2

If you have damaged or missing components, call the

Components - Fittings

Customer Helpline: 08456 400800 quoting the reference

numbers below

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 12

D

13mm Screw (F63) x 8

G H

25mm Screw (F50) x 4

J

M

Hanging bracket

(F849) x 2

Cantilevered

Hinge Arm

(F155) x 2

B

Metal dowel (F901) x 8

E

Connecting Sleeve (F432) x 2

Shelf support (F110) x 5

K

2mm Hinge
Plate (F157) x 2

N

Bent
Hinge
Arm (F154)
x 2

C

Large locking
nut (F900) x 8

F

19mm Connecting bolt (F461) x 2

I

Wall bracket (F198) x 2

L

40mm Screw (F910) x 2

O

Nail (F51) x 8

P

Soft Close
Unit (F156)

x 2

Q

4mm Hinge
Plate (F158) x 2

3

If you have damaged or missing components, call the

Components - Doors

Customer Helpline: 08456 400800 quoting the reference

numbers below

Please check you have all the panels listed below

Doors and handles are supplied separately in fascia packs.
Please see below for the correct fascia code for this unit in your chosen fascia design.

Monza Oak

Monza Beech

Imola Black Gloss

Imola Cream Gloss

Imola White Gloss

Pesaro Cream

Pesaro Oak

Ricadi

656/6225

656/6218

656/6232

656/6249

656/6256

656/6270

656/6263

656/6287

The front

surface of this

door is

protected with

a peel-off film

8

Monza Door (DPF113A)

(237 x 716mm) x 2

8 8

Imola Door (DPF113A)

(237 x 716mm) x 2

+

9 10

Ricadi Hinged
Door (D0384A)

(237 x 716mm)

Pesaro Door (DPF113A)

(237 x 716mm) x 2

Ricadi Carcase
Door (D0384A)

(237 x 716mm)

4

If you have damaged or missing components, call the

Components - Handles

Customer Helpline: 08456 400800 quoting the reference

numbers below

Please check you have all the fittings listed below

Handles are supplied separately and are located packed in the end sleeve of each fascia pack.
Please see below for the correct fascia code for this unit in your chosen fascia design.

Monza Oak

Monza Beech

Imola Black Gloss

Imola Cream Gloss

Imola White Gloss

Pesaro Cream

Pesaro Oak

Ricadi

R

Monza Door Handle (F123) x 1 Imola Door Handle (F124) x 1

656/6304

656/6294

656/6311

656/6335

656/6328

656/6359

656/6342

656/6366

R

b

25mm Screw
(F132) x 2

Ra

a

R

b

25mm Screw
(F132) x 2

R

a

Pesaro Door Handle (F125) x 1

R

b

25mm Screw
(F132) x 2

R a

Ricadi Door Handle (F126) x 1

R b R c

25mm Screw
(F132) x 1

Hole Plug

(F114) x 4

5

Assembly Instructions

Step 1

Choose which way
you would like the
door to open

You can fit the door to
the left side or right side.

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 2

Prepare the left end
panel

Refer to step 1 and, if
required, fit 2 hinge

plates onto the left
end panel , orientated
as shown.

Screw 4 metal dowels
into the holes shown on
the left end panel .

Note: Tighten metal
dowels up fully against
the panels.

Q

4

B

4

If you would like your door

to open this way, fit the

hinge plates to the left side

Q K

Q

Q

B

B

If you would like your door

to open this way, fit the

hinge plates to the right side

H=2H=4

B

H=4

Q

H=2

B

G

B

4

G

J

Fit a hanging bracket
to the left side using
2 screws , making

4

G

J

sure that the hook is
towards the back edge.

This will be the

left end panel

6

Assembly Instructions

Step 3

G

G

Prepare the right end
panel

Refer to step 1 and, if
required, fit 2 hinge

plates onto the right
end panel , orientated

Q

4

as shown.

Screw 4 metal dowels

B

into the holes shown on
the right end panel .

4

Note: Tighten metal
dowels up fully against
the panels.

Fit a hanging bracket
to the right side using
2 screws , making

G

J

4

sure that the hook is
towards the back edge.

This will be the
right end panel

B

J

4

B

Q

B

B

Q

Q K

H=4

Q

H=2H=4

H=2

Step 4

Prepare the top and
base

Insert 4 large locking

C

nuts into the top
and base as shown.

1

Note: Arrow on locking
nut must point towards
hole in edge of panel.

Tap 4 wooden dowels
into the top and base

1

. as shown.

1

Note: Wooden dowels

must not stick out from
the edge by more than
10mm or they may
damage other panels.

1

A

C

C

1

A

A

C

10mm

C

A

C

A

A

7

Assembly Instructions

Step 5

Join the right end
panel and base

Push the base onto
the right end panel .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

1

4

C

1

C

Finished

front edge

1

4

5

1

B

Step 6

Prepare the back

Tap 4 wooden dowels
into the back as
shown.

3

C

A

A

A

A

A

3

8

Assembly Instructions

Step 7

Fit the back

Push the back onto
the base and secure
with screw .

3

1

L

3

1

L

Step 8

Fit the top

Push the top onto
the right end panel
and back .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Secure the back to
the top with screw

L

. .

1

4

3

C

1

C

3

1

1

3

4

L

9

Assembly Instructions

Step 9

Insert the loose shelf

Place the loose shelf
inside the unit.

2

2

Step 10

Fit the left end panel

Push the left end panel
. onto the base

4

and top .

Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

1

1 1

1

C

C

4

1

1

10

Assembly Instructions

Step 11

Fit the loose shelf

Insert 5 shelf studs at

H

the required height.

Lift and then lower the
loose shelf down
onto the shelf studs .

2

H

2

H

H H

x 2 x 2

Step 12

Fit the backs

Slide the left back
and right back along
the grooves in the top
and base and into

1

the grooves in the panel
ends .

4

5

6

5

6

1

4 4

1

1

11

Assembly Instructions

Step 13

Fit right back

Secure the left back
and right back to the
sides of the back
using 8 nails .

O

5

6

3

O

O

5 6

O

3

O

O

O

O

O

12

Assembly Instructions

Step 14

Fit the unit to the wall

If you are joining this unit
to another one, also refer
to step 10.

To fix the unit to the wall,
place the unit in the
required position and
lightly mark the outline of
the top corners of the
unit with a pencil.

Fit the 2 wall brackets

I

to the dimensions shown
in the top diagram.
The screws and plugs
are not supplied as they
need to be the correct
type to suit your wall.

37mm

I

18mm

18mm

37mm

I

I

Warning: The
unit is heavy.
Lift with care.

I

Warning: Take
care when

drilling the wall
that you do not drill into
any pipes, wires etc. If in
doubt, consult an expert.

Place your unit onto the
wall brackets , via the
hanging brackets

I

J

which you have fitted to
the end panels of the

4

unit.

Use the screw in the
bottom of the wall
brackets to adjust the

J

height of the unit.

Finally, pull the unit up
against the wall by
tightening up the top
screw in the hanging
brackets .

J

4 4

J

I

To adjust the height of

turn the bottom screw

Pull the unit up

against the wall

by tightening

the top screw

the unit on the wall,

13

Assembly Instructions

Step 15

Joining units together

Fittings have been
supplied so you are able
to join units together.

Make sure that your first
unit is level.

Push the other unit up
against first unit and
ensure both units are
level.

Check that the ends are
flush and in line, then
clamp them together.

Using a 5mm drill bit,
drill 2 holes (approximate
positions shown circled)
in the side panel into the
adjoining side panel of
the other unit.

5mm

F

E

Push the connecting
sleeves into the holes
and then screw the
connecting bolts in
from the other side.

E

F

14

Assembly Instructions

Step 16

Prepare the doors

a: Fit 2 hinge plates

onto a door , making
sure that they face the
same way as the
diagram.

7

b: Push fit 2

cantilevered hinge arms
. into the door .

M

Secure each hinge arm
with 2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

D

K

7

MONZA, IMOLA and PRESARO DOORS ONLY

If you have the Ricadi Doors please see Step 17 or 18.

a:

K Q

b:

H=2

H=2

M

K

7

K

H=4

H=4

D

D

D

D

M

7

K

M

90

c: Push fit 2 bent hinge

arms into the other

N

door .

Secure each hinge arm
with 2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

15

7

D

c:

D

D

D

D

N

N

90

N

7

Assembly Instructions

Step 17

Prepare the doors

a: Fit 2 hinge plates

onto the carcase door
. , making sure that

9

they face the same way
as the diagram.

b: Push fit 2

cantilevered hinge arms
. into the carcase door

M

. .

9

Secure each hinge arm
with 2 screws .

D

K

RICARDI DOORS ONLY - LEFT SIDE HINGE PLATES

Only follow this step if

you have fitted the hinge

plates to the LEFT side

(see step 1).

Arch at

this end

K

K

a:

K

H=2

K Q

H=2

H=4

H=4

9

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

Push hole plugs

Q c

into the 2 unused hinge
holes.

c: Push fit 2 bent hinge

N

arms into the hinged
door .

Secure each hinge arm
with 2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

8

D

b:

Arch at

this end

R c

c:

Arch at

this end

D

D

D

D

M

M

9

D

D

D

N

D

M

90

N

90

N

8

R c

Push hole plugs

R c

into the 2 unused hinge
holes.

16

Assembly Instructions

Step 18

Prepare the doors

a: Fit 2 hinge plates

onto the carcase door
. , making sure that

9

they face the same way
as the diagram.

b: Push fit 2

cantilevered hinge arms
. into the carcase door

M

. .

9

Secure each hinge arm
with 2 screws .

D

K

RICARDI DOORS ONLY - RIGHT SIDE HINGE PLATES

Only follow this step if
you have fitted the hinge
plates to the RIGHT side

(see step 1).

K

a:

9

H=2

K Q

H=2

H=4

H=4

K

K

Arch at

this end

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

Push hole plugs

Q c

into the 2 unused hinge
holes.

c: Push fit 2 bent hinge

N

arms into the hinged
door .

Secure each hinge arm
with 2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

8

D

b:

c:

R c

D

D

D

D

M

M

9

Arch at

this end

D

D

D

N

D

M

90

N

90

N

8

R c

Push hole plugs

R c

into the 2 unused hinge
holes.

17

Arch at

this end

Assembly Instructions

Step 19

Drill the handle holes
in the door

Important: Please follow
these instructions
carefully.

Lay the door down
onto a smooth surface.

Important: Carefully
choose which holes you
need to drill.
This will depend on
which side or
you fitted the hinge
plates .

Check that the holes and
hinges are in the same
place as the diagrams.

K

7

1

2

MONZA DOOR ONLY

Carefully choose which 2 holes you will need to drill

Drill these 2 holes if

you have fitted the

hinges to the left side.

ONLY drill

these 2 holes

Small piece of

waste wood

7

Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.

Using the pilot hole in
the rear face of the door,

7

. drill through the
holes indicated opposite,
using a 2.5mm diameter
drill.

Turn the door over
and open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.

7

DO NOT drill

these holes

or

Drill these 2 holes if

you have fitted the

hinges to the right side.

O

ONLY drill

these 2 holes

Note: Drill bits are not
provided.

DO NOT drill

these holes

7

Small piece of

waste wood

18

Assembly Instructions

Step 20

Drill the handle holes
in the door

Important: Please follow
these instructions
carefully.

Lay the door down
onto a smooth surface.

Important: Carefully
choose which holes you
need to drill.
This will depend on
which side or
you fitted the hinge
plates .

Check that the holes and
hinges are in the same
place as the diagrams.

K

7

1

2

IMOLA DOOR ONLY

Carefully choose which 2 holes you will need to drill

Drill these 2 holes if

you have fitted the

hinges to the left side.

ONLY drill

these 2 holes

DO NOT drill

Small piece of

waste wood

7

these holes

Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.

Using the pilot hole in
the rear face of the door,

7

. drill through the
holes indicated opposite,
using a 2.5mm diameter
drill.

Turn the door over
and open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.

Note: Drill bits are not
provided.

7

or

Drill these 2 holes if

you have fitted the

hinges to the right side.

ONLY drill

these 2 holes

DO NOT drill

these holes

19

7

Small piece of

waste wood

Assembly Instructions

Step 21

Drill the handle holes
in the door

Important: Please follow
these instructions
carefully.

Lay the door down
onto a smooth surface.

Important: Carefully
choose which holes you
need to drill.
This will depend on
which side or
you fitted the hinge
plates .

Check that the holes and
hinges are in the same
place as the diagrams.

K

7

1

2

PESARO DOOR ONLY

Carefully choose which 2 holes you will need to drill

Drill these 2 holes if

you have fitted the

hinges to the left side.

ONLY drill

these 2 holes

Small piece of

waste wood

7

Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.

Using the pilot hole in
the rear face of the door,

7

. drill through the
holes indicated opposite,
using a 2.5mm diameter
drill.

Turn the door over
and open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.

7

DO NOT drill

these holes

or

Drill these 2 holes if

you have fitted the

hinges to the right side.

O

ONLY drill

these 2 holes

Note: Drill bits are not
provided.

DO NOT drill

these holes

7

Small piece of

waste wood

20

Assembly Instructions

Step 22

Drill the handle hole
in the door

Important: Please follow
these instructions
carefully.

Lay the hinged door
down onto a smooth
surface.

Important: Carefully
choose which hole you
need to drill.
This will depend on
which side or
you fitted the hinge
plates .

Check that the holes and
hinges are in the same
place as the diagrams.

Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.

Using the pilot hole in
the rear face of the door,

8

. drill through the hole
indicated opposite, using
a 2.5mm diameter drill.

1

K

8

2

RICADI DOOR ONLY

Carefully choose which hole you will need to drill

Drill these 2 holes if

you have fitted the

hinges to the left side.

ONLY drill

these 2 holes

DO NOT drill

this hole

Arch at top

of door

8

Small piece of

waste wood

or

Drill these 2 holes if

you have fitted the

hinges to the right side.

Turn the door over
and open out the 2.5mm
hole that you have just
drilled by drilling back
through it with a 5mm
drill.

Note: Drill bits are not
provided.

21

8

ONLY drill

these 2 holes

DO NOT drill

this hole

8

Arch at top

of door

Assembly Instructions

Step 24

Fit the carcase door

2 people are needed
here

Note: The easiest way to

attach the carcase door

7 9

. or is to fit the top
hinge first, then align and
fit the other hinge.

a: Push the hooks on

the cantilevered hinge

M

arm underneath the
front of the hinge plate
. .

Q

b: Press the front of the

hinge arm against the
hinge plate until it
clicks into place.

M

Q

a:

Q

b:

M

Push and click

M

Q

c:

M

Push

Q

This Diagram shows a monza door being fitted.

You may have chosen different doors.

Q

M

c: If you need to

seperate the hinge arm

M

. from the hinge plate,

Q

. press the button at
the end of the hinge arm
and lift it off of the hinge
plate.

7

or

9

This shows the carcase door being fitted

to hinge plates on the left side.

You may have fitted them to the right side.

22

Assembly Instructions

Step 25

Fit the carcase door

2 people are needed
here

Note: The easiest way to

attach the hinged door

7 8

. or is to fit the top
hinge first, then align and
fit the other hinge.

a: Push the hooks on

the bent hinge arm
underneath the front of
the hinge plate .

N

K

b: Press the front of the

hinge arm against the
hinge plate until it
clicks into place.

N

K

a:

K

N

K

Push and click

b:

N

K

N

c:

Push

K

N

c: If you need to

seperate the hinge arm
. from the hinge plate,

N

. press the button at

K

the end of the hinge arm
and lift it off of the hinge
plate.

d: Attach the handle

R a

. supplied with the
door or using the
screw(s) packed
with it.

7 7

R b

R b

R b

R a

7

or

8

23

Assembly Instructions

Step 26

Fit the soft close unit

Push a soft close unit
onto each cantileved
hinge arm until it
clicks into place.

M

P

M

P

Step 27

Adjust the doors if
needed

Adjust the hinge plates
and arms by turning the
screws on them
clockwise or anti­clockwise.

24

Assembly Instructions

Step 28

Fit other products to
the unit

To fit other products to
this unit, please follow
the instructions packed
with them.

We recommend that you
consult a qualified joiner
or kitchen fitter.

Assembly is complete

Warning: The
unit is heavy.
Lift with care.

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

25

ALR2527

MADE IN

BRITAIN

Dimensions

Width - 57cm

Depth - 57cm

Height - 72cm

Valencia - Corner Wall Cabinet

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 05/08/14

Important - Please read these instructions fully before starting assembly

656/5752

633/2992

633/2978

205/3079

633/2985

203/7215

hygena

Black Door Pack

Cream Door Pack

Oak Door Pack

White Gloss Door Pack

White HN Door Pack

Cabinet

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs
approximately 16kgs.
Please lift with care.

• Check you have all the
components and tools listed on
pages 2 to 5.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Parts of the assembly will be
easier with 2 people.

• Make sure you have enough
space to layout the parts before
starting.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close to
its final position (in the same
room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).

1

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• From time to time check that
there are no loose screws on
this unit.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Tools required

Rule Scissors Hammer

Eye protection
(when using a
hammer or drill)

Cross-head
screwdriver

Electric drill

• We do not
recommend the
use of power
drill/drivers for

inserting screws,
as this could damage the unit.
Only use hand screwdrivers.

• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.

• Dispose of all packaging
carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

1

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

4

2 3

Top/Base (DPF101A)

(566 x 566mm) x 2

Loose Shelf (DPF102A)

(545 x 545mm)

Back (DPF103A)

(205 x 684mm)

End Panel (DPF141A)

(320 x 716 mm) x 2

5 6

Left Back Panel (DPF104A)

(430 x 694 mm)

Right Back Panel (DPF105A)

(430 x 694 mm)

Door (DPF144B)

(238 x 716mm) x 2

7

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

A

Wooden dowel (F22) x 12

B

Metal dowel (F901) x 8

C

D

Large locking
nut (F900) x 8

F

G H

K

I

13mm Screw (F63) x 8

E

19mm Connecting bolt (F461) x 2

25mm Screw (F50) x 4

Connecting Sleeve (F432) x 2

Shelf support (F110) x 5

J

Wall bracket (F198) x 2

Hanging bracket

(F849) x 2

L

N

Q

40mm Screw (F910) x 2

Bent
Hinge
Arm (F154)
x 2

M

Cantilevered

Hinge Arm

(F155) x 2

O

Nail (F51) x 8

P

Soft Close
Unit (F156)

x 2

2mm Hinge
Plate (F157) x 2

4mm Hinge
Plate (F158) x 2

RRa

b

25mm Screw (F132) x 2

Handle (F214) x 1

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Choose which way
you would like the
door to open

You can fit the door to
the left side or right side.

If you would like your door

to open this way, fit the

hinge plates to the left side

If you would like your door

to open this way, fit the

hinge plates to the right side

Q

Prepare the left end
panel

Refer to step 1 and, if
required, fit 2 hinge

plates onto the left
end panel , orientated
as shown.

Screw 4 metal dowels
into the holes shown on
the left end panel .

Note: Tighten metal
dowels up fully against
the panels.

Fit a hanging bracket
to the left side using
2 screws , making
sure that the hook is
towards the back edge.

4

B

4

B

Q

Q

B

B

B

B

This will be the

left end panel

4

J

G

G

J

4

G

Q K

H=2H=4

H=4

H=2

Q

Assembly Instructions

5

Step 3

Step 4

Prepare the top and
base

Insert 4 large locking
nuts into the top
and base as shown.

Note: Arrow on locking
nut must point towards
hole in edge of panel.

Tap 4 wooden dowels
into the top and base
. as shown.

Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.

C

C

1

1

10mm

A

A

1

1

B

B

B

B

4

This will be the

right end panel

Q

Prepare the right end
panel

Refer to step 1 and, if
required, fit 2 hinge

plates onto the right
end panel , orientated
as shown.

Screw 4 metal dowels
into the holes shown on
the right end panel .

Note: Tighten metal
dowels up fully against
the panels.

Fit a hanging bracket
to the right side using
2 screws , making
sure that the hook is
towards the back edge.

4

B

4

J

4

G

J

G

G

Q

Q

C

C

C

C

A

A

A

A

1

C

C

C

C

A

A

A

A

1

Q K

H=2H=4

H=4

H=2

Q

Assembly Instructions

6

Step 5

Step 6

Join the right end
panel and base

Push the base onto
the right end panel .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

1

1

4

C

C

B

C

1

4

1

4

A

A

Prepare the back

Tap 4 wooden dowels
into the back as
shown.

A

3

A

A

3

Finished

front edge

L

Assembly Instructions

7

Step 7

Step 8

L

3

1

Fit the back

Push the back onto
the base and secure
with screw .

Fit the top

Push the top onto
the right end panel
and back .

Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

Secure the back to
the top with screw
. .

4

3

1

1

C

C

L

3

1

1

L

1

4

3

3

Assembly Instructions

8

Step 9

Step 10

Fit the left end panel

Push the left end panel
. onto the base
and top .

Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and top .

Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.

1

1

4

1 1

C

C

Insert the loose shelf

Place the loose shelf
inside the unit.

2

2

4

1

1

Assembly Instructions

9

Step 11

Step 12

H

H H

x 2 x 2

Fit the loose shelf

Insert 5 shelf studs at
the required height.

Lift and then lower the
loose shelf down
onto the shelf studs .

H

H

2

2

Fit the backs

Slide the left back
and right back along
the grooves in the top
and base and into
the grooves in the panel
ends .

5

6

1

4

1

5

6

1

1

4 4

Assembly Instructions

10

Step 13

O

Fit right back

Secure the left back
and right back to the
sides of the back
using 8 nails .

5 6

5

6

3

O

O

O

O

O

O

O

O

3

I

I

Assembly Instructions

11

Step 14

18mm

37mm

I

18mm

37mm

I

To adjust the height of

the unit on the wall,

turn the bottom screw

Pull the unit up

against the wall

by tightening

the top screw

J

I

Warning: The
unit is heavy.
Lift with care.

Fit the unit to the wall

If you are joining this unit
to another one, also refer
to step 10.

To fix the unit to the wall,
place the unit in the
required position and
lightly mark the outline of
the top corners of the
unit with a pencil.

Fit the 2 wall brackets
to the dimensions shown
in the top diagram.
The screws and plugs
are not supplied as they
need to be the correct
type to suit your wall.

Place your unit onto the
wall brackets , via the
hanging brackets
which you have fitted to
the end panels of the
unit.

Use the screw in the
bottom of the wall
brackets to adjust the
height of the unit.

Finally, pull the unit up
against the wall by
tightening up the top
screw in the hanging
brackets .

Warning: Take
care when

drilling the wall
that you do not drill into
any pipes, wires etc. If in
doubt, consult an expert.

I

I

J

4

J

J

4 4

Assembly Instructions

12

Step 15

5mm

Joining units together

Fittings have been
supplied so you are able
to join units together.

Make sure that your first
unit is level.

Push the other unit up
against first unit and
ensure both units are
level.

Check that the ends are
flush and in line, then
clamp them together.

Using a 5mm drill bit,
drill 2 holes (approximate
positions shown circled)
in the side panel into the
adjoining side panel of
the other unit.

Push the connecting
sleeves into the holes
and then screw the
connecting bolts in
from the other side.

E

F

E

F

7

Assembly Instructions

13

Step 16

K

K

a:

b:

90

M

H=2

H=2

H=4

H=4

K Q

K

N

Prepare 1 of the doors
to be the carcase
door

a: Fit 2 hinge plates

onto a door , making
sure that they face the
same way as the
diagram.

b: Push fit 2

cantilevered hinge arms
. into the door .

Secure each hinge arm
with 2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

7

P

D

7

7

D

D

D

D

M

M

Assembly Instructions

14

Step 17

Fit the carcase door

2 people are needed
here

Note: The easiest way to

attach the carcase door
. is to fit the top hinge
first, then align and fit the
other hinge.

a: Push the hooks on

the cantilevered hinge
arm underneath the
front of the hinge plate
. .

b: Press the front of the

hinge arm against the
hinge plate until it
clicks into place.

c: If you need to

seperate the hinge arm
. from the hinge plate,
. press the button at
the end of the hinge arm
and lift it off of the hinge
plate.

Q

M

Q

M

7

M

Q

This shows the carcase door being fitted

to hinge plates on the left side.

You may have fitted them to the right side.

7

a:

b:

c:

Push and click

Push

M

M

M

Q

Q

Q

Q

M

7

Assembly Instructions

15

Step 18

90

D

D

D

D

Prepare the other
door to be the hinged
door

Push fit 2 bent hinge
arms into the other
door .

Secure each hinge arm
with 2 screws .

Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the front edge of the
door.

N

N

O

N

7

D

Assembly Instructions

16

Step 19

Drill the handle holes
in the hinged door

Important: Please follow
these instructions
carefully.

Lay the door down
onto a smooth surface.

Important: Carefully
choose which holes you
need to drill.
This will depend on
which side you fitted the
hinge plates .

Check that the holes and
hinges are in the same
place as the diagrams.

Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.

Using the pilot hole in
the rear face of the door,
. drill through the
holes indicated opposite,
using a 2.5mm diameter
drill.

Turn the door over
and open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.

Note: Drill bits are not
provided.

7

K

7

7

Drill these 2 holes if

you have fitted the

hinges to the left side.

Drill these 2 holes if

you have fitted the

hinges to the right side.

or

Small piece of

waste wood

ONLY drill

these 2 holes

DO NOT drill

any other holes

7

ONLY drill

these 2 holes

Small piece of

waste wood

DO NOT drill

any other holes

7

PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY

TO CHOOSE WHICH 2 HOLES YOU WILL NEED TO DRILL

Assembly Instructions

17

Step 20

This shows the hinged door being fitted to

carcase door on the left side.

You may have fitted it to the right side.

Fit the hinged door

2 people are needed
here

Note: The easiest way to

attach the hinged door
. is to fit the top hinge
first, then align and fit the
other hinge.

a: Push the hooks on

the bent hinge arm
underneath the front of
the hinge plate .

b: Press the front of the

hinge arm against the
hinge plate until it
clicks into place.

c: If you need to

seperate the hinge arm
. from the hinge plate,
. press the button at
the end of the hinge arm
and lift it off of the hinge
plate.

d: Attach the handle

. supplied with the
door using the
screw(s) packed
with it.

K

N

K

N

7

N

K

R a

R b

7

7

R b

R b

R a

a:

b:

c:

Push and click

Push

K

N

K

N

K

N

K

N

Assembly Instructions

18

Step 21

Fit the soft close unit

Push a soft close unit
onto each cantileved
hinge arm until it
clicks into place.

P

M

Step 22

P

M

Adjust the doors if
needed

Adjust the hinge plates
and arms by turning the
screws on them
clockwise or anti­clockwise.

Assembly Instructions

19 ALR2664

Step 23

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Fit other products to
the unit

To fit other products to
this unit, please follow
the instructions packed
with them.

We recommend that you
consult a qualified joiner
or kitchen fitter.

Assembly is complete

Warning: The

unit is heavy.
Lift with care.