Clothes Rail With Lower Swing Out Rail
Assembly Instructions - Please keep for future reference
359/1815
Dimensions
Width - 84cm
Depth - 44cm
Height - 113-187.5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 12/11/2014
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
Components - Parts
If you have damaged or missing components,
call the Customer Helpline: 03456 400800
Please check you have all the fittings listed below
Black Coated Tube x 1(872 mm)
1
Black Coated Tube x 1 (968 mm)
3
Chrome Plated Tube x 1 (500 mm)
5
Black Coated Tube x 1 (900 mm)
2
Chrome Plated Tube x 2 (840 mm)
4
Chrome Plated Tube x 2 (950 mm)
6
Black Coated Tube x 2 (790 mm)
7
Plastic Clipper x 3
9
Plastic Connector x 1
11
Plastic Base x 3
12
Black Coated Tube x 1
8
Pole Locker x 3
10
Castor without stopper x 6
13
2
Assembly Instructions
Step 1
Connect the Black
Coated Tube with
Plastic Base .
Import Note: Ensure
that tubes are tightly
connected with Plastic
Base .
12
See fig 1
7
12
12 7
fig 1
Step 2
Connect Black Coated
Tube and along
1
with another Black
Coated Tube and
then insert them with
Plastic Bases .
Insert Black Coated
Tube to Plastic Base
.
12
3
Insert Plastic Clipper
through each Black
Coated Tube ,
and .
3
See fig 2
2
8
12
1 2
9
9
9
12
1 2
8
9
3
12
fig 2
3
Assembly Instructions
Step 3
Connect Pole Locker
10
along with Chrome
Plated Tube and .
6
4
Insert Plastic Connector
to Chrome Plated
11
Tube .
6
Connect Chrome Plated
Tube with Black
Coated Tubes and
.
6
2
3
Insert Chrome Plated
Steel Tube into Black
Coated Tube .
4
1
See fig 3
10
4
1
4
6
11
2
10
6
3
Step 4
Connect Chrome Plated
Tube to Plastic
Connector and insert
Pole Locker at the
end.
Insert Castor into
the Plastic Base .
See fig 4
5
11
10
13
12
fig 3
5
11
10
12
13
fig 4
4
Assembly Instructions
Step 5
After you have followed
each step mentioned
above, you can adjust
the height to desired
position by loosen
Plastic Clipper on
each Black Coated Tube
, and and
2
1
screw them tightly.
Finally, the assembly
is complete.
9
3
9
See fig 5
9
9
2
1
3
fig 5
Important Note: The
Maximun Safe Load
for long rail is 15 kg
and 5 kg for short rail.
Evenly distributed.
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Loading...