Argos Q072519 ASSEMBLY INSTRUCTIONS

Tall Wide Bookcase With Drawers
Assembly Instructions - Please keep for future reference
213/7816
Dimensions
Width - 78cm
Depth - 29cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Issue 1 - 14/05/14
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Check you have all the components and tools listed on pages 2 and 3.
Remove all fittings from the plastic bags and separate them into their groups.
Keep children and animals away from the work area, small parts could choke if swallowed.
Make sure you have enough space to layout the parts before starting.
Do not stand or put weight on the product, this could cause damage.
Assemble the item as close to its final position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your floor.
This product has been produced from natural timber; you may notice some variation in the grain and colour of different component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture.
On unpacking the furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time.
This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing or carpeted surfaces during assembly.
We do not recommend the use of power drill/drivers for
inserting screws,
as this could damage the unit. Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Care and maintenance
Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product.
Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age.
From time to time check that there are no loose screws on this unit.
This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
Components - Panels
Please check you have all the panels listed below
Right side panel (178.2 x 26cm)
1
top
Left side panel (178.2 x 26cm)
2
Right front frame (178.2 x 6.5cm)
3
Left front frame (178.2 x 6.5cm)
4
top
underside
Top panel (78 x 29cm)
7
underside
Fixed shelf x 2
8
(70.4 x 23.6cm)
Adjustable shelf x 2
9
(70.4 x 23.6cm)
Middle back panel x 3 (128.2 x 17.4cm)
5
Side back panel x 2 (128.2 x 11.7cm)
6
Drawer right side
Drawer front x 2
12
(60.4 x 18cm)
Top front frame x 2
16
(65 x 6.5cm)
Drawer right side
13
(22 x 14cm)
x 2
Bottom front frame
17
(65 x 6.5cm)
Drawer left side
14
(22 x 14cm)
x 2
Small back panel x 2
10
(72.2 x 23.4cm)
Drawer bottom x 2
11
(58.6 x 21.6cm)
15
Cross rail (70.4 x 6.5cm)
18
Drawer back x 2
(57.6 x 14cm)
Front plinth (78 x 9.2cm)
19
H profile (70 x 1.8cm)
22
Side plinth x 2
20
(26.8 x 9.2cm)
Drawer runner x 4
13
21
(24 x 5.5cm)
Block x 6
23
(10 x 2cm)
2
If you have damaged or missing components,
Components - Fittings
call the
Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Ø6x30mm Wooden dowel x 8
D E
G
22mm Bolt x 8
J
Drawer handle x 4
M
Wall strap x 1
B
B
Ø8x30mm Thick wooden dowel x 28
H
Metal dowel x 12
K
Shelf support x 8
N
Nail x 16
C
14mm Screw x 3
F
50mm Screw x 835mm Screw x 3430mm Screw x 40
I
Locking nut x 12
L
Washer x 2
Tools required
Phillips screwdriver (small & medium)
Small hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
3
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape measure
Eye protection (when using a hammer or glue)
Assembly Instructions
Step 1
Fixing right front frame to the right side panel
(Two people required for an easier assembly).
a: Insert right side panel
1
into right front frame
3
through joints.
Note:
Before fixing the
blocks into place it is important to ensure that the slot and groove of parts and are fully pushed together and lined up correctly at the top and bottom.
b: Place blocks
between the two marks as shown. First fix to the side panel using screws .
c: Fix front frame through
blocks using screws
E
23
.
23
1
23
3
E
a: b: c:
3
E
1
23
Yes!No!
Top
23
Attention: correct position of panel.
Top
23
3
1
E
23
Step 2
Fixing left front frame to the left side panel
(Two people required for an easier assembly).
a: Insert left side panel
2
into left front frame
4
through joints.
Note:
Before fixing the
blocks into place it is important to ensure that the slot and groove of parts and are fully pushed together and lined up correctly at the top and bottom.
b: Place blocks
between the two marks as shown. First fix to the side panel using screws .
23
2
23
4
E
a: b: c:
4
E
2
23
Yes!No!
23
4
2
E
Top
23
Attention: correct position of panel.
Top
c: Fix front frame through
blocks using screws
E
23
.
23
4
Assembly Instructions
Step 3
Fitting Metal dowels.
Screw metal dowels into right side panel , left side panel and top panel .
7
H
1
2
Insert metalNote: dowels as far as shown.
Do not over tighten.
H
1
2
H
7
H
H
H
H
H
Step 4
Insert shelf supports into the right side panel
1
and left side panel
2
.
K
K
1
K
2
K
K
5
Assembly Instructions
Step 5
B
Insert dowels into the indicated parts.
B
B
B
1
2x
and
2
8
B
Step 6
Assembling the cabinet.
Insert top front frames
16
and bottom front frame into holes on right side panel , as shown.
Fit cross rail to the right side panel then fix it using screw .
17
1
18
1
E
16
18
21
4x
B
B
Attention!
17
16
17
1
18
E
6
Assembly Instructions
Step 7
Fixing shelves.
With help, fit fixed shelves
8
to right side panel .
Attention!
Round edges on shelves must be facing front.
4Insert locking nuts
shelvesinto where
shown.
Use a screwdriver to turn locking nuts clockwise
I
to lock.
Do not over tighten.
1
I
Attention:
8
8
8
I
1
I
I
Step 8
Fixing left side panel.
With help, place left side panel properly ensuring dowels in shelves, frames and cross rail are all fit into their holes at the same time.
Insert 4 locking nuts into shelves where shown.
Use a screwdriver to turn locking nuts clockwise to lock.
Do not over tighten.
Fix cross rail to the left side panel using screw .
With help, carefully turn the product with its front facing down.
2
I
I
18
2
E
I
2
I
8
I
I
I
E
8
18
7
Assembly Instructions
Step 9
Fixing top panel.
With help, fit top panel
7
to the cabinet.
Insert 4 locking nuts
I
into side panels where shown.
Use a screwdriver to turn locking nuts clockwise
I
to lock.
Do not over tighten.
Fix bottom front frame
17
to the right and left side panels using screws
C
as shown in the diagram.
I
I
7
I
C
I
C
17
C
C
Step 10
Fixing drawer runner.
Fit drawer runners to the side panels then fix it using screws as shown.
21
F
21
21
21
F
F
21
21
8
Assembly Instructions
Step 11
Fixing back panels.
Important:
Cabinet beMUST ‘square’ when back panels are attached.
a: Place back panels
starting with a side back panel as shown in the diagram ( you can easily identify part as it has a straight cut on one of the edges)
back panels flush to the side panels and
as shown.
6
6
.
Attention:
Do not attach side
6
1
2
, leave a gap of ,4mm
a:
4mm
4mm
5
5
5
6
1
b:
D
6
6
2
D
b: Fix all back panels
using screws .
Important!
After fixing the back panels, with help, carefully turn the product with its front facing up.
D
5
5
5
6
9
Assembly Instructions
Step 12
Fixing back panels.
a: Attach small back
10
panel at the top first using nails .
N
10
22
10
b: Position profile onto
back panel (just attach).
22
c: Carefully slot the
second back panel into the profile and fix it to the cabinet using nails .
Important!
After fixing the back panels, with help, carefully turn the product with its front facing up.
10
N
Step 13
a: Fix side plinths to
the side panels using screws .
D
20
N
N
N
10
22
10
Note:
Make sure side plinths are aligned to the bottom and front edges of the side panels.
b: Fix front plinth
to the bottom front frame using screws .
Chanfred edges to be
facing up!
plinth is aligned to the bottom edge of the side panels and in line to the side plinths.
20
19
D
Note:
Make sure front
19
a:
b:
a:
19
20
D
20
D
10
Assembly Instructions
Step 14
Important:
With help, carefully stand the product upright.
Position adjustable shelves into place. Make sure round edge is facing front.
9
Note:
These shelves are
adjustable.
9
9
9
Step 15
Insert dowels into the drawer right side and drawer left side .
A
13
14
2x
13
A
A
2x
14
A
11
A
Assembly Instructions
Step 16
Drawer assembly.
a: Attach drawer right
13
side and drawer left
14
side to the drawer
12
front using screws .
E
b: Slide drawer bottom
11
into slots on drawer
sides and position drawer
15
back in place.
a:
b:
13
E
14
E
E
E
12
15
11
c: Holding the drawer
15
back , press the drawer sides and fix them using screws .
d: Using bolts attach
drawer handles to drawer front.
Repeat step 16 for the other drawer.
D
G
J
c:
d:
D
D
G
G
J
J
12
Assembly Instructions
Step 17
Insert drawers into unit. With the back of the drawers past the front frames, use a hammer to tap dowels in flush to drawer sides. This is a safety catch to stop drawer falling out.
Step 18
B
BB
Fixing to wall.
Furniture must be fixed to
a wall. Fix wall strap to top of furniture using washer and screw . With help, move furniture into position.
L C
M
Note: Wall plugs not supplied. The correct type of fixing must
be used for your wall, seek
professional advice if in doubt.
wall
L
M
C
L
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
13
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs are supplied with your product:
- these are only suitable for use in masonry walls.
If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
Failure of the product due to using incorrect fixings is the responsibility of the installer.
Important: When drilling into walls always check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualifed tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls
You can use one of the following types of wall plug if your walls are made of brick, breeze block, concrete, stone or wood.
No.1 General Purposewall plug No.3 Cavity Fixingwall plug No.5 Hammer Fixingwall plug
Generally aerated blocks should not be used to support heavy loads, use a specialist fitting in this case. For light loads, general purpose wall plugs can be used.
No.2 Plasterboardwall plug
For use with plasterboard partitions or hollow wooden doors.
No.4 Cavity Fixing-Heavy Duty
wall plug
For use with walls stuck with plasterboard. The hammer fixing allows it to be fixed to the wall rather than the plasterboard. Always check the fixing is secure to the retaining wall.
No.6 Shield Anchorwall plug
Heavy loads
For use when attaching light loads on to plasterboard partitions.
Care & Maintenance
For use when fitting or supporting heavy loads such as shelving, wall cabinets and coat racks.
Safety: Always check the fitting and location to ensure your safety in and around the home.
For use with heavier loads such as TV & HiFi speakers and satelite dishes etc.
Fitting: From time to time check the fitting to ensure the wall plugs or screws do not become loose.
Loading...