Phoenix 2 Half Door Storage Cubes
Assembly Instructions
-
Please keep for future reference
162/2690
166/6230
166/6632
181/5971
Dimensions
Width - 70cm
Depth - 35.5cm
Height - 70cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Version2 Date: 23/10/13
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
rom the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not use this item if any
components are missing or
damaged.
Care and maintenance
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
r.
• Parts of the assembly will be
easier with 2 people.
• Assembly to be carried out by
the competent adult only.
• During assembly children should
be kept away from the product due
to the potential risk of injury.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• Argos Ltd. MK9 2 NW. • This product is suitable for
children in the age 6 or above.
• Maximum load: 20 kgs.
• Regularly check all fastenings
to ensure that they are properly
tightened.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
If you have damaged or missing components,
Components - Panels
call the Customer Helpline: 08456 400800
Please check you have all the panels listed below
Top/Bottom panel x 2
1
(69.9 x 34.9cm)
Pilot holes for
guidance only
Middle support x 2
4
(34.9 x 32.6cm)
Side panel x 2
2
(66.8 x 34.9cm)
Shelf
3
(66.8 x 34.9cm)
Back panel x 2
5
(34.5 x 69.5cm)
Pilot holes for
guidance only
Door panel x 2
6
(32 x 32cm)
2
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
A
50mm Dowel x 2
D
25mm Screw x 2
G
Screw cover x 4
J
Door hinge x 4
M
Wall strap x 2
Note
:
Please keep the
M O
B
30mm Dowel x 12
E
12mm Screw x 6
H
Door Stopper x 2
K
Metal plate x 2
N
Wall plug x 1
C
50mm Screw x 8
F
Nail x 22
I
Handle x 2
L
33mm Screw x 1
O
14mm Screw x 3
Tools required
Phillips screwdriver
(medium & large)
Bradawl
(or sharp point)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
3
Small
hammer
0 1 2 3 4 5 6
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
105
110 115 120 125 130 135 140 145 150 155 160 165 170
Assembly Instructions
Step 1
Attaching door
stoppers
Door stoppers onto the
Middle supports .
E
H
4
E
E
H
4
E
E
H
X 2
Step 2
Attaching metal plates
& door hinges
E
Metal plates onto the
Door panels .
Insert the Door hinges
into the Door panels .
K
6
J
6
E
J
K
J
6
E
J
K
X 2
4
Assembly Instructions
Step 3
Attaching the side
panels
Insert Dowels into
a:
the
Shelf and Middle
supports .
Middle
the Shelf .
3
4
supports onto
3
B
A
4
a:
Finished
front edge
B
B
B
Finished
front edge
B
A
B
B
3
4
A
4
B
B
B
B
b:
Fix the
onto the Shelf .
p
3
2
b:
2
Finished
front edge
3
2
5
Assembly Instructions
Step 4
Attaching the door
panels
a:
Carefully locate the Door
panel onto the unit,
6
aligning the Door hinges
with the corresponding
holes.
C
Bottom panel onto the
1
unit.
Note:
Ensure the Door
hinges are aligned with
the corresponding holes.
a:
Finished
front edge
C
C
C
1
C
6
b:
Carefully locate the Door
panel onto the unit,
6
aligning the Door hinges
with the corresponding
holes.
C
Top panel onto the unit.
Note:
Ensure the Door
1
hinges are aligned with
the corresponding holes.
b:
Finished
front edge
C
C
C
1
C
6
6
Assembly Instructions
Step 5
Fixing back panel
F
Back panels onto the
unit.
5
Important:
The unit MUST
be ‘square’ when
the back is attached.
back edge
back surface
F
5
5
1
2
Step 6
Attaching the handles
D
Handles onto the Door
panels .
I
6
I
D
I
6
D
D
6
I
7
Assembly Instructions
7
Step
Attaching the screw
covers
Use
Screw covers to
cover the screw heads.
G
G
G
G
G
Step 8
Finishing the unit
With help, place the unit in
the intended position.
Assembly is complete.
8
Assembly Instructions
Step
9
Fixing with another unit
Warning:
The
Lift with care.
a:
U
S
Wall strap to link
another unit from the
back.
It is recommended that the
Fixing to wall
With help, move the unit
into position.
M
unit is heavy.
O
a:
X 2
M
b:
L
O
O
Top panel
Note:
Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt
N
M
M
L
wall
O
N
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
b:
remove the unit.
Drill a hole and insert Wall
N
plug .
O
strap onto the top panel.
M
Reposition
strap using Screw .
L
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
9
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Revision 2 - 7/10/09
Loading...