Office Stool
Assembly Instructions - Please keep for future reference 244/9315
Dimensions
Width - 54cm
Depth - 54cm
Height - 48-63.5cm
Important
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
- Please read these instructions fully before starting assembly
Issue 1 - 28/04/14
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Parts of the assembly will be
easier with 2 people.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Do not stand on the stool.
• Do not use this stool as step
ladder.
• From time to time check that
there are no loose screws on
this unit.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Unit weight: 3.75 kgs.
• Maximum safe weight of user:
110kgs.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
1
If you have damaged or missing components, call the
Components - Parts
Customer Helpline: Argos = 0345 6400800
Please check you have all the parts listed below
1 Gas Lift
Seat
(44 x 37 x 7.5cm)
4
Leg base
(Ø56 x 8cm)
2
(13.5 x 25 x 4.5cm)
3Mounting Plate
(Ø5.1 x 32.5-46cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
M6 x 12mm Bolt x 4 Castor x 5
B
C
Allen key x 1
2
Assembly Instructions
Step 1
Attaching mounting
plate
Place the seat upside
1
down on a flat protected
surface.
Position the mounting
plate making sure the
2
arrow on the plate is
pointing to the front of
the seat as shown.
Align 4 holes as shown
and fix using bolts .
A
Tighten bolts using allen
C
key .
Step 2
Attaching castors
Attach the castors into
holes on the base and
secure by pressing down
firmly.
B
4
A
A
B
2
A
1
A
2
A
arrow
1
front
4
B
B
Step 3
Step 3
Attaching gas lift
Insert the gas lift into
hole on the base as
3
4
shown & secure by
pressing down firmly.
Important:
Remove plastic
tip cover on gas
lift before
assembling.
B
remove
plastic tip cover
B
3
4
3
Assembly Instructions
Step 4
Attaching the seat
Position the seat as
shown and insert the gas
3
lift into the hole of the
mounting plate .
Secure by pressing down
firmly.
1
2
1
2
3
Gas lift operation
To adjust the seat higher,
lift up the lever under the
seat and release at
desired height.
To lower the seat, lift up
the lever while seated on
the stool.
Assembly is complete.
Pull up lever
to adjust
seat height
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
4
Loading...