Argos Newport - 3 Door Robe ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 103.5cm
Depth - 50cm
Height - 172cm
Newport - 3 Door Robe
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 20/05/15
Important - Please read these instructions fully before starting assembly
331/9152
395/8496
339/6199
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 58kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Rule
Tools required
Rule
ScissorsSquare
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left End (DF285)
(1703 x 495mm)
Right End (DF286B)
(1703 x 495mm)
2
Top (DF520)
(1032 x 496mm)
Base (DF522)
(996 x 470mm)
Door (DF288B)
(1635 x 328mm) x 3
Divider (DF525)
(1623 x 469mm)
Plinth (DF521)
(996 x 65mm)
3
4
5
76
9 Small Back (X1650-351)
(1650 x 351mm)
Large Back (X1650-668)
(1650 x 668mm)
Hanging Rail (FHR657)
(657mm long)
8
10 11
Shelf (DF526)
(332 x 468mm) x 2
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 10
C
E F
G H I
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
25mm Screw (F50) x 3
J
Nail (F51) x 36
Plastic Nail (F91) x 4
M
Large locking nut (F900) x 10
13mm Screw (F63) x 20
Handle (F314) x 3
Rail holder
(F1014) x 2
P
O
R
Q
D
40mm Screw (F910) x 4
K
L
Nail screw (F277) x 6
Back holder (F276) x 6
* These can also be round
Hinge plate (F523) x 6
Hinge arm (F522) x 6
Hinge arm (F518) x 3
Hinge plate (F523) x 3
These hinge plates and arms are in the bag of 6 labelled AHP1546
These hinge plates and arms are in the bag of 3 labelled AHP1043
Shelf stud (F110) x 8
N
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
C
Finished
front edge
Step 2
O
O
O
O
O
Prepare the left side
Screw 3 metal dowels into the left side .
Note: Tighten the metal dowels up fully against the panels.
Insert 2 large locking nuts into the left side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Fit 3 hinge plates to the left side making sure that the slot is facing towards the finished front edge.
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Note: The hinge plates used on the left and right ends are in the bag of 6 labelled AHP1546.
Note: The hinge plates used on the left and right ends are in the bag of 6 labelled AHP1546.
B
1
B
C
C
C
I
F
B
B
C
1
1
O
1
O
O
O
B
B
B
C
Prepare the right side
Screw 3 metal dowels into the right side .
Insert 2 large locking nuts into the right side .
Fit 3 hinge plates to the right side making sure that the slot is facing towards the finished front edge.
B
2
C
2
2
O
2
I
F
1
Finished
front edge
Loading...
+ 11 hidden pages