MADE IN
BRITAIN
Dimensions
Width - 70.5cm
Depth - 50cm
Height - 172cm
Newport - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 5 - 20/05/15
Important - Please read these instructions fully before starting assembly
244/1409
258/8403
417/4262
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 38.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2 4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Door (DF288B)
(1635 x 328mm) x 2
Left End (DF285)
(1703 x 495mm)
Top (DF287)
(701 x 496mm)
Plinth (DF290)
(665 x 65mm)
Base (DF291)
(665 x 470mm)
5
3
7
8
Hanging Rail (FHR657)
(657mm long)
6
Back (X1650-691)
(1650 x 691mm)
Right End (DF286B)
(1703 x 495mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 10
C
D E F
G H I
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
25mm Screw (F50) x 2
Nail (F51) x 32
Plastic Nail (F91) x 4
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
J
K
Large locking
nut (F900) x 10
13mm Screw (F63) x 14
Handle (F314) x 2
Rail holder
(F1014) x 2
L
Hinge (F520) x 6
Hinge Plate
(F521) x 6
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
C
Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
J
J
J
J
J
Prepare the left side
Screw 3 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the
left side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 3 hinge plates to
the left side making
sure that the slot is
facing towards the
finished front edge.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
B
1
B
C
C
C
I
F
B
B
C
1
1
J
1
J
J
J
B
B
B
C
I
F
Prepare the right side
Screw 3 metal dowels
into the right side .
Insert 2 large locking
nuts into the
right side .
Fit 3 hinge plates to
the right side making
sure that the slot is
facing towards the
finished front edge.
Push a rail holder into
the right side and
secure with screw .
B
2
C
2
2
J
2
I
F
1
I
F
1
Finished
front edge
A
Finished
front edge
Finished
front edge
Assembly Instructions
5
Prepare the base
Insert 4 large locking
nuts into the base .
4
Step 3
Step 4
C
C
C
C
C
4
Finished
front edge
B
C
Fit the base to the
right side
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 5
2
4
C
C
4
2
4
C
C
A
10mm
A
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the plinth .
A
5
5
C
5
Finished
front edge
Assembly Instructions
6
Step 6
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
2
5
C
5
2
5
Step 7
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the base and plinth
. .
Step 8
Prepare the top
Screw 4 metal dowels
into the top .
1
C
4
5
1
4
5
B
B
B
B
B
3
3
Finished
front edge
Assembly Instructions
Step 9
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
4
C
1
2
4
1
2
b:
Fit the back and tap in
the plastinails
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Stand the unit up for
the next step.
8
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8
y
y
x
G
8
H
H
H
H
H
1
2
Warning: The
unit is heavy.
Lift with care.
7
Step 10
1
2
x
Assembly Instructions
8
Step 11
Step 12
Prepare the 2 doors
Push fit 3 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
K
7
90
K
K
F
F
K
F
F
K
F
F
7
x 2
6
6
I
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
6
I
Assembly Instructions
9
Step 13
Fit the doors and
handles
2 people are needed
here
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using
screw .
Note: Do not
overtighten screw .
e:
K
K
K
J
J
J
K
J
E
D
D
7
7
a: b:
c: d:
B
J
K
A
J
K
J
J
K
K
K
J
B
D
7
7
E
E
Assembly Instructions
10
Step 14
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the top (or
base) of the unit is level,
front-to-back and sideto-side in the 3 positions
shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3052
Step 15
Fit the overbalance
protector kit
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
L
L
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
L
Strap
Washer
Screw
TOP OF UNIT
L
Loading...