MADE IN
BRITAIN
Dimensions
Width - 98cm
Depth - 39cm
Height - 75.5cm
Jarvia - Desk
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 08/10/13
Important - Please read these instructions fully before starting assembly
143/6202
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 17kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2507A)
(976 x 388mm)
Upright (D2510A)
(320 x 337mm)
Drawer Base (T550)
(312 x 327mm) x 2
Modesty (D2511A)
(900 x 323mm)
Drawer Front (D2513A)
(363 x 157mm) x 2
Rail (D2512A)
(352 x 80mm)
Left Side (D2508A)
(720 x 386mm)
8
6
5
Right Side (D2509A)
(720 x 386mm)
4
3
7
Left Drawer Side (W500LH)
(330 x 95mm) x 2
Right Drawer Side (W500RH)
(330 x 95mm) x 2
Drawer Back (W301-95) x 2
(301 x 95mm)
9 10
11
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 12
C
E
Large locking
nut (F900) x 8
F
G
Small metal dowel (F893) x 4
H
19mm Screw (F461) x 4
Small locking
nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Hollow core
locking nut
(F892) x 4
I
D
Knock-in Peg (F171) x 8
13mm Screw (F52) x 12
L
b
L
c
L
a
L
d
13mm Screw (F63) x 8
Tools required
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Handle (F306) x 2
R Runner (F962) x 2
L Runner (F963) x 2
L Runner (F961) x 2
R Runner (F964) x 2
R
L
7
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2 x 2
B
7
8
B
B
E
Step 2
B
B
Prepare the drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
E
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
8
9
7
E
8
9
Groove
8
E
E
E
8
9
E
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
7
7
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
8 9
7
K
K
K
K
10
8 9
11
10
10
K
8 9
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
F
H
7
11
8
9
11
8
H
9
H
10
F
7
x 2
x 2
x 2
Assembly Instructions
6
Step 7
Fit runners to the
drawers
Turn the drawer
assemblies over.
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
9
L c
8
7
J
L d
L c
Runners must be
pushed up against
the drawer front
8
9
7
Step 8
B
B
Prepare the top
Screw 4 small metal
dowels into the top .
Screw 2 metal dowels
into the top .
Note: Tighten metal
dowels up fully against
the panels.
G
C
G
G
G
G
4
4
B
4
x 2
Front edge
L
L
L d
R
R
J
J
J
J
Finished
front edge
Finished
front edge
Front edge
Assembly Instructions
7
Step 9
D
D
D
I
L
I
I
L
I
B
Prepare the upright
Fit 2 runners to the
upright .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Insert 2 large locking
nuts into the upright
. .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Screw a metal dowel
into the upright .
L a
5
I
I
D
5
L a
I
Finished front edge
I
1st
screw
2nd
screw
I
3rd
screw
L a
L a
5
B
L
L
L
L
D
B
Step 10
Fit the upright to the
top
Push the upright
down onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the upright .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
4
5
D
D
5
5
4
I
I
Assembly Instructions
8
Step 11
Prepare the left side
Push 2 hollow core
locking nuts into the
left side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Screw 2 metal dowels
into the left side .
Step 12
C
C C
1 1 1
B
C
C
B
C
1
1
C
C
B
1
L
L
L
L
Fit the left side
Push the left side
onto the top .
The 2 hollow core
locking nuts fitted to
the left side must
slide over the 2 small
metal dowels fitted to
the top .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
4
1
G
C
C
4
1
1
4
Front edge
Front edge
Finished
front edge
A
Assembly Instructions
Step 13
Step 14
Prepare the modesty
Insert 4 large locking
nuts into the modesty
. .
D
6
L
L
L
L
4
1
D
D
D
D
6
Fit the modesty
Push the modesty
onto the left side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
Step 15
6
1
D
6
6
D
D
Plain chipboard
surface
Prepare the rail
Tap 2 wooden dowels
into the rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the rail .
D
3
A
10mm
A
A
3
9
3
Assembly Instructions
10
Step 16
Prepare the right side
Fit 2 runners to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Screw 3 metal dowels
into the right side .
L b
2
I
I
Finished
front edge
C
C
R
L b
L b
I
Finished front edge
I
1st
screw
2nd
screw
I
3rd
screw
B
B
R
I
I
L b
B
I
I
C
2
C
C
B
2
R
R
R
R
2
Finished
front edge
2
3
Step 17
Fit the rail to the right
side
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
3
2
D
3
Front edge
I
I
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2911
Step 18
L
L
L
L
4
Step 19
6
Fit the right side
Push the right side
onto the assembly.
The 2 hollow core
locking nuts fitted to
the right side must
slide over the 2 small
metal dowels fitted to
the top .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the rail and modesty
. .
Carefully stand the
unit up for the next
step.
2
G
C
C
2
4
D
3
6
2
3
Side
panel
Drawer
Fit the drawers
Slide the wheels on the
runners fitted to the
drawers over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
4
Warning: The
unit is heavy.
Lift with care.
Loading...