Haversham - 2 Dr 2 Drw Sideboard
Assembly Instructions
- Please keep for future reference
146/5572
Dimensions
Width - 83,5cm
Depth - 39cm
Height - 80,5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Issue 1 - 01/10/10
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
.
Check you have all the
components and tools listed on
pages 2 and 3.
.
Remove all fittings from the
plastic bags and separate them
into their groups.
.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
.
Make sure you have enough
space to layout the parts before
starting.
.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Care and maintenance
.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Do not stand or put weight on
the product, this could cause
damage.
.
Assemble the item as close
to its final position (in the same
room) as possible.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
.
Parts of the assembly will be
easier with 2 people.
.
Dispose of all packaging
carefully and responsibly.
.
We do not
.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
.
From time to time check
that there are no loose
screws on this unit.
.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Components - Panels
Please check you have all the panels listed below
Right front leg (78,5 x 4,5cm)
01
Right back leg (78,5 x 4,5cm)
02
Top panel (83,5 x 39cm)
05
Left front leg (78,5 x 4,5cm)
03
Left back leg (78,5 x 4,5cm)
04
Door X 2 (54,9 x 36,2cm)
06
x 36cm)73,5
Shelf X 2(
07
H profile 73 ( x 2,2cm)
09
Side panel X 2 (73,5 x 29cm)
10
Drawer front X 2
12
Mid le walld
13
( x 19,5cm)36
Back panel X 2(
08
Drawer botto m X 2
11
(
x 37,4cm)74,4
x 30,7cm)34,8
Large runner X 2
14
(
35 x 2,8cm)
Runner X 2
15
(
35 x 1,9cm)
Drawer left side X 2
16
(
35 x 13cm)
Drawer right side X 2
17
(
(
35 x 13cm)
Drawer back X 2
18
(
(29,6 x 13cm)
2
If you have damaged or missing components,
Components - Fittings
call the Customer Helpline: 08456 400 800
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
A
8,0 x 30mm Wooden dowel
D
A
3,5 x 14mm Screw X 17
G
10 x 10 Nail X 30
J
Locking nut X 16
N
Hinge X 4
X 38
A
B
3,5 x 25mm Screw X 8
E
Handle X 4
H
Foot pad 4 X
L
Hinge plate X 4
O
Metal dowel X 16
C
3,5 x 30mm Screw X 36
F
Plastic pin X 4
I
Washer X 2
M
Wall strap X 1
Tools required
Phillips screwdriver
(medium & large)
Small
hammer
Ruler - Use this ruler to help correctly identify the screws
5
0
10 15 20 25 30 35 40
55
45
50
60 65 70
75
80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
m
2
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
3
Assembly InstructionsAssembly InstructionsAssembly InstructionsAssembly Instructions
Assembly Instructions
A
Step 1
O
02
01
Parts , , and
03
04
are labelled for easier
identification.
Insert wooden dowels
into large runners .
Insert wooden dowels
02
into leg , , and
04
as shown.
01
Screw metal dowels
02
into leg , , and
.
04
01
A
14
A
03
O
03
Do note over
tighten metal
dowels.
02
01
O
A
A
O
A
01
04
O
O
A
O
A
A
O
O
02
A
O
A
O
A
03
A
O
O
A
A
A
A
14
O
A
A
O
03
A
14
Step 2
a)
Fit
side panel , left
front leg and left back
leg together.
03
04
b) Insert locking nuts
where shown. Use a
screwdriver to turn locking
nuts clockwise to lock.
Fix hinge plates using
screws as shown.
D
Fix runner to side panel
10
using screws . Make
sure holes in runner are
positioned as shown.
10
L
14
B
04
J
J
04
J
.a)
10
A
Make sure holes
face this side
.b)
03
B
J
J
J
B
14
J
J
D
D
14
L
4
Assembly Instructions
Step 3
a) Fit side panel , right
front leg and right back
leg together.
01
02
b) Insert locking nuts
10
J
where shown. Use a
screwdriver to turn locking
.b)
nuts clockwise to lock.
Fix hinge plates using
.
screws as shown.
D
Fix runner to side panel
10
using screws . Make
L
14
B
sure holes in runner are
positioned as shown.
.a)
J
J
D
J
D
D
L
J
B
D
J
B
01
J
14
Make sure holes
face this side
10
14
02
A
J
Step 4
Insert wooden dowels
into the indicated parts.
=
07
13
=
A
A
13
A
A
A
A
Front view
A
A
2 x
A
A
5
Assembly Instructions
Step 5
Fix shelves to the
07
assembled right side panel
10
using screws as
C
as shown.
Step 6
Fix assembled left side
panel using screws
10
as shown.
C
C
01
10
02
C
03
07
C
C
C
07
C
C
C
Step 7
Fix small middle wall to
top panel using screws
C
. Screw metal dowels
where shown.
O
05
ATTENTION!
Make sure
panels are
positioned as show
in the picture.
13
10
04
C
C
C
PAINTED EDGE
O
O
C
C
C
C
C
13
C
05
O
O
05
O
6
Assembly Instructions
Step 8
05
Fix top panel to the
assembled part. Then,
insert locking nuts as
shown. Use a screwdriver
to turn locking nuts
clockwise to lock.
05
J
J
J
J
J
J
Step 9
With the help of a hammer,
fix foot pads as shown.
Fix runner using
screws . Make sure
holes in runners are
positioned as shown.
H
15
B
H
Make sure holes
4x
H
H
H
15
face this side
15
B
H
7
Assembly Instructions
Step 10
Fix runner using
screws . Make sure
holes in runners are
positioned as shown.
15
B
Make sure holes
face this side
15
B
15
Step 11
Position back panels
within rebates with profile
09
in place as shown.
Attach back panels using
G
nails where shown.
IMPORTANT
Cabinet must be
“square” when
back is attached.
08
X
G
G
G
G
G
G
G
G
G
08
09
08
G
G
G
G
G
08
G
G
G
G
G
8
Assembly Instructions
Step 12
16
16
A
12
A
Insert wooden dowels
Into drawer sides and .
17 .
Attach drawer sides
17
and to drawer front
using screws .
C
Step 13
Slide drawer base into
grooves as shown.
Attach drawer back
using screws .
11
18
C
2x
A
2x
11
2x
17
17
16
16
A
A
C
C
12
C
2x
E
C
C
C
Fix handle using screw
C
.
E
Step 14
Attach hinges N to the
06
doors 4 using screws J
as shown.
Fix handle E using screw
C
B as shown.
N
D
E
C
C
2x
N
D
N
C
06
C
06
18
D
D
D
N
06
E
E
9
Assembly Instructions
Step 17
Fixing wall strap:
Fix wall strap H to top of
product (edge) using
washer I and screw J as
shown.
Insert wooden dowels
into the runners as shown.
Hanging doors:
With help, slot door hinges
N
N onto hinge
plates M and tighten
M
screw.
Hinge adjustment:
1- To move doors left or
right, loosen screw shown
and move doors to suit.
Re-tighten screws.
M
I
D
A
A
M
I
D
A
A
A
A
06
06
1.
2.
M
N
A
M
2 - To move doors in or out,
loosen screw shown and
move doors to suit.
Re-tighten screws.
3 - To move doors up or
down, loosen screws
shown and movedoors to
suit. Re-tighten screws.
Step 18
Place drawers onto runners
and slide past dowels
fitted to runners.
Then, with hammer, tap
plastic pins in flush with
drawer side, this is a safety
catch to stop drawer falling
out.
F
1.
N
2.
3.
F
F
F
Assemble is complete
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
10
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls
You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Loading...