Argos Hallingford - Dresser and Stool ASSEMBLY INSTRUCTIONS
Assembly Instructions - Please keep for future reference
Issue 4 - 28/01/14
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dresser
Dimensions
Width - 99cm
Depth - 40cm
Height - 74.5cm
Hallingford - Dresser and Stool
305/2323
305/2316
305/2282
305/2347
305/2299
Stool
Dimensions
Width - 51.5cm
Depth - 35.5cm
Height - 45cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 29kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
1
Top (D2326A)
(990 x 396mm)
Upright (D2329A)
(333 x 372mm)
Modesty (D2330A)
(598 x 244mm)
Rail (D2331A)
(342 x 66mm) x 2
Back (X350-366)
(350 x 366mm)
Left Side (D2327A)
(721 x 372mm)
2
Right Side (D2328A)
(721 x 372mm)
5
3
Drawer Front (D2309A)
(362 x 162mm) x 2
Drawer Base (T304-327)
(304 x 327mm) x 2
Left Drawer
Side (W500LH)
(330 x 95mm) x 2
Right Drawer
Side (W500RH)
(330 x 95mm) x 2
Drawer Back (W293-95)
(293 x 95mm) x 2
7
4
6
8 9
10 11
13
12
Stool Top (D2332A)
(513 x 353mm)
Stool Base (D2336A)
(478 x 308mm)
Stool Drawer
Front (D2338A)
(472 x 126mm)
Stool Left Side (D2333A)
(395 x 350mm)
17
14
Stool Right Side (D2334A)
(395 x 350mm)
15
Stool Rail (D2335A)
(478 x 124mm) x 2
18
Stool Drawer
Back (W445-95)
(445 x 95mm)
Stool Drawer Base (T456-297)
(456 x 297mm)
Stool Left
Drawer Side
(W410LH)
(300 x 95mm)
Stool Right
Drawer Side
(W410RH)
(300 x 95mm)
Stool Seat Pad (FHALPAD)
(458 x 300mm)
16
19 20 21
22
23
Dresser
Stool
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
B C
D E F
G H
Small locking
nut (F3) x 6
L
Nail (F51) x 10
13mm Screw (F52) x 12 13mm Screw (F63) x 12
I
A
Wooden dowel (F22) x 14
19mm Screw (F461) x 4
Metal dowel (F901) x 36
Large locking
nut (F900) x 30
Knock-in Peg (F171) x 12
M
R Runner (F160) x 2
b
L Runner (F161) x 2
M
c
L Runner (F159) x 2
M
a
R Runner (F162) x 2
M
d
350mm long
K
9mm Screw (F73) x 4
J
9mm Screw (F74) x 2
N
280mm long
O
Handle (F278) x 2
25mm Screw (F50) x 4
Drawer runner (F1004) x 2
4
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
6
x 2
B
6
8
B
B
C
B
B
9
Groove
8
C
C
C
8
9
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
6
x 2 x 2
x 2
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
C
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
6
C
8
9
C
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
8 9
6
10
8 9
11
10
10
E
8 9
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
O
G
6
6
8
9
11
E
E
E
E
8
10
9
11
O
6
G
G
x 2
x 2
x 2
Assembly Instructions
6
Step 7
Fit runners to the
drawers
Turn the 2 drawer
assemblies over.
Fit runner , marked
with ‘R’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit runner , marked
‘L’, to the bottom edge
of the left drawer side
using the same method.
8
M d
9
6
I
M c
I
I
Runners must be
pushed up against
the drawer front
M d
R
R
I
I
L
M c
L
6
8
9
x 2
D
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels
into each rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into each rail .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
A
Step 8
x 2
5
5
D
5
Plain
chipboard
surface
Assembly Instructions
7
Step 9
Step 10
B
D
2
5
5
A
Prepare the right side
a: Fit 2 runners to
the right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
B
D
2
2
M b
2
H
H
I
M b
M b
H
Finished front edge
H
1st
screw
2nd
screw
H
3rd
screw
M b
Finished front edge
I
a:
b:
A
2
H
H
M b
H
H
H
M b
H
D
I
I
D
B
B
Finished
front edge
Finished
front edge
2
2
Join the rails to the
right side
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
D
5
2
5
D
Finished
front edge
Loading...