Argos HALLINGFORD 32 R BEE ASSEMBLY INSTRUCTIONS

New Hallingford
2 Door 3 Drawer Wardrobe

DR899054

Assembly Instructions - Please keep for future reference

2274951

2498696

2684321

2599409

2328450

Dimensions

Tip: To prevent damage,

Width - 99,7cm

Depth - 60,3cm

Height -205,7cm

we recommend that you

build your unit on the

carton(s) it was packed in.

Important – Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020

Issue 3 - 12-02-2016

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

• Check you have all the
components and tools listed on
pages 2 and 3.

• Remove all fittings from the
plastic bags and separate them
into their groups.

• Keep children and animals
away from the work area, small
parts could choke if swallowed.

• Make sure you have enough
space to layout the parts before
starting.

Care and maintenance

• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.

• Do not stand or put weight on
the product, this could cause
damage.

• Assemble the item as close
to its final position (in the same

room) as possible.

• Assemble on a soft level
surface to avoid damaging the
unit or your floor.

• Parts of the assembly will be
easier with 2 people.

• From time to time check that
there are no loose screws on
this unit.

•To reduce the
likelihood of
damaging your
product please
ensure that your

power drill is set on a low torque
setting.
Warning: Only use a manual
screwdriver to attach the hinges.

• Dispose of all packaging
carefully and responsibly.

• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.

Instruction video

• This manual is provided with an additional instruction
video. If the icon on the right is displayed at a particular
step in the manual, Follow the link: http://nlink.nu/vid01
Or scan the QR code on the left with your phone.

See page 1 for link
to instruction video!

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

1

Components - Panels

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [e-mail]

Please check you have all the panels listed below

Left side

1

(205.6 x 58cm)

P2349b

Top/Bottom x 2

5

(96.7 x 57.7cm)

P1341

Drawer base x 3

9

(45.4 x 34.9cm)

BO33955B

Right side

2

(205.6 x 58cm)

P2349b

Drawer wrap x 3

10

(35 x 46.7 x 10cm)

LA1869

Upright small

6

(47.5 x 57.7cm)

P2893

Mirror door small

3

(151.2 x 48.8cm)

PS3719

Large horizontal

7

(96.7 x 57.6cm)

P1342

Drawer front x 3

11

(48.8 x 15.7cm)

P4315

Door x 1

4

(199.2 x 48.8cm)

P3724

Small horizontal

8

(47.6 x 57.6cm)

P1343

Foldy back

12

(199.3 x 98cm)

BO33933

Plinth front

13

(96.6 x 14cm)

P7334C

Plinth back

14

(96.6 x 5.4cm)

P7335C

Pelmet

15

(99.9 x 4.5cm)

FA247

2

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

110 115 120 125 130 135 140 145 150 155 160 165 170

105

Components - Fittings

For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [e-mail]

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.

Fittings Drawers

B

FK1980

FK1981

C

H

FK1011

20mm Screw x 10

J

Small locking
nut x 6

Fittings Carcase

A

40mm Screw x 6

F

12.5 mm Screw x 2

M

Hanger rail support x 2

P

Hinge back x 6

S

Peg x 2

G

L-Bracket x 1

9mm Srew x 6

FK1010

U

Drawerbase support x 6

FK1324

D

15mm Screw x 13

FK1309

K

Nail x 60

FK1217

N

Q

FK1234

T

Door/Drawer handle x 5

FK1235

H

24mm locking screw x 22

FK1250

FK1400

FA1515 FK1419

PM1884

Hanger rail large x 1

FK1268FK1269

Hinge door x 6

GR1975

FK1011

24mm locking screw x 6

X

Glue x 1

E

10mm Fixing screw drawer x 12

L

Nail holder x 1

O

15mm Screw x 12

PM16951

R

Runner x 6

V

Wall plug and parkerscrew x 1

I

Large locking
nut x 22

FA1510

FK1301

FK1311

ZF99936

FK1012

Tools required

Phillips screwdriver

(medium & large)

Drill

Flatblade screwdriver

(medium)

Piercer

(small)

5mm Suitable drill bit

5mm Suitable drill bit

Ruler - Use this ruler to help correctly identify the screws

3

Stairs

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

0 1 2 3 4 5 6

Spirit level

Setsquare

Small
hammer

Ruler/tape
measure

Scissors

Eye protection
(when using a
hammer or drill)

Assembly Instructions

Step 1

Drawer assembly x 3

a: Insert two small locking

nuts J into drawer wrap

0.

Make sure the ‘arrow’ on
J�is pointing towards the
hole in the edge of 0.

b: Screw 24mm locking

screws H into holes
shown on back of drawer
front !.

J

a:

10

J

b

H

11

H

Make sure 24mm locking
screws H are tightened
right up against drawer
front !.

c: Slide drawer base 9

into grooves shown on
drawer wrap 0.

H

H

11

c:

9

10

4

Assembly Instructions

Step 1 - continued

d: Turn the drawer wrap

assembly over and push
onto the drawer front !.
Use a phillips or flatblade
screwdriver, that is a good
fit to turn 24mm locking
srew I as far as it will go

- more than 1/2 turn.

d

H

I

e: Fix drawer handle T

onto drawer front ! using
30mm screw B.
Turn over drawer and slide
drawerbasesupports U
in corner as shown and fix
them, using the attached
screws.

Step 2

e:

a:

11

I

B

B

11

T

U

U

Attaching runners

a: Slide top of runners R

foreward and fix on right side
2 as shown using 10mm
fixing screw drawer E.

5

2

E

R

E

E

E

R

R

2

R

Finished
front edge

Assembly Instructions

StepStep 2 - continued

b

b: Slide top of runners R

back.

Fix through 3rd hole of
runner R and pre-drilled
holes of right side 2 using
10mm fixing screw drawer
E.

3

R

E

OO

Fix through 1st and 7th
hole of runners R using
15mm screw O.

Note: there are no pre­drilled holes for 15mm
screw O.

Repeat a and b on upright
small 6.

Step 3

Insert fittings

a: Screw 24mm locking

screw H into right side

2.

Note: Insert 24mm
locking screw H as far as
shown.

Do not over tighten.

H

a:

3

R

R

R

O

E

H

2

H

H

H

P

P

H

O

E

O

2

O

E

O

O

Finished
front edge

H

H

H

H

P

2

P

H

P

Screw hinge back P onto
right side 2.

b: Attach hanger rail

support M using 12.5mm
screw F onto right side

2.

b

Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.

F

M

2

2

F

M

6

Assembly Instructions

Step 4

Attaching plinths

a: Allign the sides of

plinth front # with bottom
5 as shown and attach
using 40mm screw A.

Note: there are no
predrilled holes for
40mm screw A.

Note: top and bottom
panels 5 are identical.
Only prepare one of the
panels at this satge.
This will be the bottom
panel

Repeat with plinth back
$.

Step 5

Insert locking screws

14

A

Unfinished

back edge

A

A

5

Top side

A

13

H

5

Top side

H

a: Screw 24mm locking

screw H into bottom 5.

Step 6

Attaching panels

Position bottom 5, small
horizontal 8, large
horizontal 7 and top 5
onto right side 2.

Insert large locking nuts I
into bottom 5, small
horizontal 5, large
horizontal 7 and top 5
where shown.

Use a screwdriver to turn
locking nuts I clockwise
to lock.

Unfinished

back edge

I

I

I

I

I

I

I

2

I

I

8

I

5

7

5

M

I

M

I

7

Assembly Instructions

Step 7Step

Insert locking screws

Screw 24mm locking
screw H into upright
small 6.

Step 8

Attaching panels

Two people are needed
here.

Position upright small 6
onto bottom 5 and small
horizontal 8.

Insert two Large locking
nuts I into upright small
6 and small horizontal 8
where shown.

H

H

H

6

Unfinished

back edge

8

I

I

I

5

I

I

6

M

I

M

I

Use a screwdriver to turn
locking nuts I clockwise to
lock.

Step 9

Insert fittings

Screw 24mm locking
screw H into left side 1.

Note: Insert 24mm
locking screw H as far
as shown.

Do not over tighten.

Screw hinge back P
onto upright 1.

Attach hanger rail
support M using 12.5mm
screw F onto left side

2.

Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.

H

H

H

1

H

P

H

P

1

P

P

H

F

M

1

H

F

M

H

1

8

Assembly Instructions

Step 10

Attaching panel

Two people are needed
here.

Position left side 1 onto
bottom/top 5 and large
horizontal 7.

Insert large locking nuts I
in top/bottom 5 and large
horiziontal 7.

Use a screwdriver to turn
locking nuts I clockwise
to lock.

M

I

M

I

5

7

I

I

I

I

I

5

I

1

I

I

Step 11

Fitting back panel

Attach foldy back @ to back
of wardrobe with the
coloured surface facing the
inside of the unit using nails
K and.
Use nail holder L to hold
the nails K vertical and at
correct distance as you
secure the foldy back @.
Nails K should be spaced
about 150mm apart.

Important:
Cabinet MUST
be ‘square’
when back is
attached.

12

K

Stand up the unit!
2 people required.

9

L

AssemblyInstructions

SStep 12

Attaching pelment and
L-bracket

Position pelment % onto
top % as shown, fix by
using 40mm screws A.

Position L-Bracket G onto
top 5 as shown, fix by
using 15mm screw D.

Note: there are no
pre-drilled holes for 15mm
screw D.

Use V to fix on the wall,
please see last page for
more information.

Step 13

Inserting hanger rails

Place hanger rail large N
into hanger rail supports
M.

a:

N

M

D

V

G

V

5

A

S

15

A

b:

Step 14

Inserting drawers

a: Pull runners out.Slide

drawers onto runners
so they butt up against
back of drawer front.

b: Fix through drawer

sides into runners using
9mm screws C.

Step 15

Fitting hinges to doors

Fix three hinge door Q
to door 4 and mirror
door small 3 using
15mm screws D.

Attach door handles T
using 30mm screws B.

C

1st small

threaded hole

Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.

D

See page 1 for link

Q

4

3

D

D

Q

3

4

B

B

T

to instruction video!

D

Q

D

Q

10

Assembly Instructions

Step 16

Hanging doors

a: With help, slot hinge

door Q onto hinge back
P.

a:

See page 1 for link
to instruction video!

Q

P

P

Q

P

Q

b: Tighten screw shown

to lock hinges in position.

Repeat a and b for other
door.

See ‘Hinge adjustment’
in step 17 if the doors
need adjusting.

c: Before adjusting the

doors, use a spirit level to
check if the base of this
unit is level front-to-back
and side-to-side in the
three positions shown.

c:

P

Q

b:

P

Q

Q

Use pegs S to square
your unit. Knock peg S in,
as far as you require,
under the ends of the unit
and then snap off flush
with the panel.

11

SNAP!

S

AssemblyInstructions

Step 17

Hinge adjustment

a: To move doors up

or down: loosen screws
shown and move doors
to suit.

Once doors are aligned,
re-tighten.

b: To move doors in

or out: loosen screw
shown and move doors
to suit.

Re-tighten screws.

Warning: Do not use an electric screwdriver to attach the
hinges as this can weaken the fixing.

a:

See page 1 for link
to instruction video!

b:

c: To move doors left

or right: loosen screw
shown and move doors
to suit.

Re-tighten screws.

c:

12

A Guide to - Wall Mounting & Fixings

Important note:

If plastic wall plugs
are supplied with your
product:

- these are only suitable for
use in masonry walls.

If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.

Failure of the product due to
using incorrect fixings is the
responsibility of the installer.

Important: When drilling into walls always

check that there are no hidden wires or pipes etc.

Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.

Hints:

1: General rule: Always use a larger screw and wall plug

if you are not sure.

2: Ensure you use the recommended drill bit to match the wall

plug and hole size.

3: Ensure you drill the hole horizontally, do not force the drill or

enlarge the hole.

4: Take extra care when drilling high walls, ceilings and ceramic

tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.

5: Ensure wall plugs are well fitted and are a tight fit in the

drilled hole.

Types of walls

No.1 “General Purpose” wall plug

Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.

No.2 “Plasterboard” wall plug

You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.

No.3 “Cavity Fixing” wall plug

For use with plasterboard partitions or
hollow wooden doors.

No.4 “Cavity Fixing-Heavy Duty”

wall plug

No.5 “Hammer Fixing” wall plug

For use with walls stuck with
plasterboard. The hamemr fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.

No.6 “Shield Anchor” wall plug

Heavy loads

For use when attaching light loads on
to plasterboard partitions.

Care &
Maintenance

13

For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.

Safety: Always check the fitting

and location to ensure your safety
in and around the home.

For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.

Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.