Page 1
New Hallingford - 2 Door Sliding Robe
Assembly Instructions - Please keep for future reference
2667537
2498043
2747017
2362241
2458856
Dimensions
Width - 100,5cm
Depth - 60,3cm
Height -205,7cm
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
DR89958
Issue4 - 02/03/2016
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• From time to time check that
there are no loose screws on
this unit.
•To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Dispose of all packaging
carefully and responsibly.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Instruction video
• This manual is provided with an additional instruction
video. If the icon on the right is displayed at a particular
step in the manual, Follow the link: http://nlink.nu/homeretail1
Or scan the QR code on the left with your phone.
See page 2 for link
to instruction video!
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2
Page 3
Components - Panels
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the panels listed below
Left side
1
(205.6 x 58cm)
P2350
5
Top
(96.7 x 55.7cm)
P1564
Right side
2
(205.6 x 58cm)
P2350
6
Bottom
(96.7 x 55.7cm)
P1565
Slide door
3
(196.3 x 50cm)
P3723
4
Mirror slide door
(196.3 x 50cm)
PS3722
7
Large horizontal
(96.7 x 46.7cm)
P1563
Plinth front
9
(96.6 x 14cm)
P7334C
Foldy back
8
(199.3 x 98cm)
BO33933
Plinth back
10
(96.6 x 5.4cm)
P7335C
Plinth top
11
(96.7 x 7cm)
P7293
12
Pelmet
(100.5 x 6.5cm)
FA250
3
Page 4
Components - Fittings
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: Help@ClickSpares.co.uk
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Door-fittings
FK1400
D
E
FK1318
J
FK1274
Backpanelscrew x 5
(4x15mm)
K
Sliding door guide x 4
Fittings Carcase
A
Chipboardscrew x 10
(4x40mm)
G
L-Bracket x 1
F
Pozi screw x 2 (4x12.5mm)
R
Doorstop x 5
U
Hanger rail x 1
(959mm)
Screw x 21
FK1273
L
Sliding door roller x 2
FK1324
B
Expando housing x 3
FK1235
H
Twister leg x 14
FK1309
M
Hanger rail support x 2
FK1417
S
Peg x 3
PM1884
W
(3.9x32mm)
(5x24mm)
FK1272
(20x12mm)
FK1011
FK1217
FK1234
PK1654
Sliding rail x 4
(966mm)
Sliding door roller adjustable x 2
FK1416
Q
Felt x 6
FK1056FK1051
C
Expanding dowel x 3
I
(5x8.5mm)
FK1012
Twister cam x 14
(15x12mm)
P
Nail x 60
PR1964
T
Handle moulding x 3
(1904mm)
ZF99936
X
Wall plug and parkerscrew x 1
FA1515
Tools required
Phillips screwdriver
(medium & large)
Drill
Flatblade screwdriver
(medium)
Piercer
(small)
5mm Suitable drill bit
2.5mm Suitable drill bit
Ruler - Use this ruler to help correctly identify the screws
4
Stairs
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Spirit level
Setsquare
Small
hammer
Ruler/tape
measure
Scissors
Eye protection
(when using a
hammer or drill)
Page 5
Assembly Instructions
Step 1
Insert fittings
a: Attach hanger rail
support M using 12.5mm
screw F onto sides 1 2.
Note: Two pannels
b: Screw twister leg H
into sides 1 2.
a:
H
b:
H
I
1
2
F
H
M
M
2
I
H
H
F
H
I
H
Note: twister leg H as far
as shown.
Do not over tighten.
Step 2
Attaching plinths
Align the sides of plinth
front 9 with bottom 6 as
shown and attach using
chipboardscrew A.
Note:
predrilled holes for 40mm
screw A.
Repeat with plinth back
0.
1/2
5
Page 6
Assembly Instructions
Step 3
Insert fittings
a: Insert expando
housings B into top 5.
Flip panel
b: Carefully knock sliding
rail W into top 5 by using
a hammer.
a:
b:
B
B
B
5
5
Reapeat b for bottom 6.
6
6
Page 7
Assembly Instructions
Step 4
Attaching panel
Position top 5, bottom 6
and horizontal 7.
Insert twister cam I into
panels 567 where
shown.
Usa a screwdriver to turn
twister cam I clockwise
to lock.
Temporary support panel
7 with packaging material
until attached to left side
1.
I
I
I
I
2
I
I
Finished
front edge
I
7
Temporary
support
5
6
M
I
M
I
Step 5
Repeat Step 4 for the
left side 1 .
6
Locate the 'mating'
panel over the Cam Leg.
I
I
Insert the Cam so the
longer 'slot' is pointing
towards the Cam Leg.
5
7
I
I
I
1
Use a Flat Bladed
Screwdriver to turn Cam
clockwise as far as it will go
I
The final 'locked' position will
be more than half a turn.
7
Page 8
Assembly Instructions
Step 6
Fitting back panel
Important!
Cabinet MUST
be ‘square’
before back is
attached.
Attach foldy back 8 to
back of wardrobe with
the coloured surface facing
the inside of the unit using
nails P.
Nails P should be spaced
about 150mm apart.
B
A:A = B:B
A
A
B
A
B
8
B
A
P
See page 2 for link
to instruction video!
8
Page 9
Assembly Instructions
Step 7
Align the unit
Stand up the unit
Use a spirit level to check
if the base of this unit
is level front-to-back (1),
side-to-side (2) and
top-to-bottom (3) in the
three positions shown.
3
Use pegs S to level your
unit in all three direction
shown. Knock peg S in,
as far as you require,
under the ends of the unit
and then snap off peg
flush with the panel.
1
2
SNAP!
S
9
Page 10
Assembly Instructions
L
Step 8
Insert hanger rail
Place hanger rail U onto
hanger rail supports M.
GLASS handle with care
U
S
M
Step 9
Insert fittings
Stick felts Q onto mirror
slide door 4 where shown.
Insert Sliding door roller L
in mirror slide door 4 on
the side which is flush with.
the handle mouldings T.
Insert sliding door roller
adjustables J in slide door
4 on the other side, fix
them with
backpannelscrews D.
Insert sliding door guides
K on the other end of the
mirror slide door 4.
K
Q
K
Q
Q
Q
4
D
D
Q
J
Q
L
Q
10
Page 11
3
K
K
Assembly Instructions
TTEEEEEEEEEEEEE
E
4
Step 10
Fitting handle to
mirrordoor
GLASS handle with care
E
Hold hande mouldings T
up against front of mirror
slide door 4, make sure
the ends are flush with one
end of the mirror slide door
4.
Screw screws E into the
‘V’ groove of the handle
moulding T.
Tip: start with the end
screws, then the centre
screw and finally the other
screws.
Step 11
Insert Sliding door roller L
in slide door 3 on the
side which is flush with the
handle mouldings T.
Insert sliding door roller
adjustables J in slide door
3 on the other side, fix
them with
backpannelscrews D.
Insert sliding door guides
K on the other end of the
slide door 3.
Flush with
end of Door
Flush with
end of Door
D
J
T
T
See page 2 for link
to instruction video!
D
L
flush
E
E
E
E
E
E
E
E
E
E
E
E
E
E
Step 12
Fitting handle to door
Hold hande moulding T
up against front of slide
door 3, make sure the ends
are ush with one end of the
slide door 3.
Screw screws E into the
‘V’ groove of the handle
moulding T.
Tip: start with the end 3
screws, then the centre
screw and finally the other
screws.
end of Door
T
Flush with
E
E
E
3
E
E
E
E
11
Page 12
3
4
7
LJK
Assembly Instructions
11
Step 13
Fitting of the doors
Important!
Double check if the
unit is level before
fitting the doors. If
this is not the case
please go back to
step 12.
a. Fit bottom slide door 3
into the rear track and lean
the top back to horizontal
7.
b.Fit mirror slide door 4
into the front track and
secure it.
c.Then fit top slide door 3
in rear track and secure.
See diagrams for more
information abour the fitting
of the doors.
To fit the bottom of the Doors
L
This lug fits into
the groove in
the track
To fit the top of the Doors
J
This lug fits into
K K
The switch in
the top glides
must be in this
position prior
to fitting the top
of the Doors.
press the switch
the groove in
the track
When the top
of the Door is
in position,
to push lug into
the groove of
the track.
Step 14
Insert fittings
Screw expanding dowel C
into plinth top !.
Step 15
Attaching plinth
Position the plinth top !
above the unit and slot
expanding dowels C into
the expando housing B.
The top of the plinth top !
must be flush with the top
of the unit.
Turn the screws in the
expando housings B as far
as they will go.
See page 2 for link
to instruction video!
C
11
Mirrored Door
C
C
12
Page 13
12
AAA
A
6
Assembly Instructions
Step 16
Attaching pelmet
Position the pelmet @
above the unit drilling-holes
and turn the screws A
as far as they will go.
Step 17
Attaching L-bracket
Position L-Bracket G onto
top 6 as shown, fix by
using 15mm screw D.
Note: there are no
pre-drilled holes for 15mm
screw D.
Use X to fix on the wall,
please see last page for
more information.
X
G
D
X
13
Page 14
R
Assembly Instructions
Step 18
Attaching door-stops
Stick 2 door-stops
onto the outside edge of
each plain door to act as
and side panels.
R
R
R
R
14
Page 15
Assembly Instructions
Level & square the unit
Level & square the unit
up: Knock the pegs S in,
as far as you require,
under the ends of the
unit and then snap off
flush with the panel.
If your doors do not run smoothly
For more detailed
information see step 7.
Raise the door
To raise the door, loosen
the screws and swivel the
glide towards the ‘+’ arrow.
Re-tighten the screws.
SNAP!
S
Lower the door
To lower the door, loosen
the screws and swivel the
glide towards the ‘-’ arrow.
Re-tighten the screws.
15
Page 16
A Guide to - Wall Mounting & Fixings
Important note:
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls
No.1 “General Purpose” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
No.2 “Plasterboard” wall plug
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
No.3 “Cavity Fixing” wall plug
For use with plasterboard partitions or
hollow wooden doors.
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
For use with walls stuck with
plasterboard. The hamemr fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
No.6 “Shield Anchor” wall plug
Heavy loads
For use when attaching light loads on
to plasterboard partitions.
Care &
Maintenance
16
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
Loading...