Verona Coffee Table
Assembly Instructions - Please keep for future reference
609/5033
610/6812
Dimensions
Width - 90cm
Depth - 45cm
Height - 41cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
issue 1 4/23/10
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
●Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
Do not stand on the panels, this
could cause damage.
Assemble the unit as close to its
final position (in the same room)
as possible.
Assemble on a soft level
surface to avoid damaging the unit
or your floor.
Parts of the assembly will be
easier with 2 people.
●From time to time check that
there are no loose screws on this
unit.
We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
Dispose of all packaging carefully
and responsibly.
Warning: The unit weighs
approximately 7.4kgs.
Please lift with care.
●This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
Components - Panels
Please check you have all the panels listed below
Table top (90 x 45cm)
1
If you have damaged or missing components,
call the Customer Helpline:08456 400800
3
Post x 4 (37.1 x Ø3.5cm)
Foot x 4 (4.7 x 3.4cm)Ø
4
2
Shelf (70 x 35cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Cap screw x 4
Pre-assembled at 4
Ruler - Use this ruler to help correctly identify the screws
2
Assembly Instructions
Step 1
Step 1
Fitting the legs
a: Unscrew Cap screws
A 4
a from the Feet .
b: Use Legs to fix the
Feet onto the Shelf
4
2 .
2
3
a:
A
4
b:
3
c: Use Cap screws to
fix the Top panel onto
the unit.
A
1
2
4
A
c:
1
3
Assembly Instructions
Step 2
Finishing the unit
Finally place the unit in
the desired location.
Note: Before use always
make sure the unit is
secure.
Assembly is complete.
If you need help or have damaged or missing parts, call the
Customer Helpline : 08456 400800
4
Components
1 x Table Top
A
1 x Shelf
B
4 x Foot
D
Verona Beech / Silver Coffee Table
Simple Assembly Instructions - Please keep for future reference
4 x Leg
C
Fittings
A
4 x Cap Screw
IMPORTANT
1. Read these instructions carefully and
familiarise yourself with the procedure
before assembling the unit.
2. Check that you have all the component
parts following the list on the back
8-03
cover and familiarise yourself with
each part before proceeding.
3. Take all the fittings out of the plastic bag
and separate them into their groups.
4. Ensure you have enough space to lay out
all the parts before assembly.
5. To avoid scratching it is recommended
that you assemble the unit on a soft
level surface.
Assembly Instructions
Assembly Instructions
Stage 1 – Fitting the Legs
1. Unscrew Cap Screws A from the
Feet D.
See fig. 1.
2. Use Legs C to fix the Feet D
onto the Shelf B.
See fig. 2.
Stage 2 – Finishing the Unit
A
fig. 1
D
C
B
1. Finally place the unit in the desired
location.
See fig. 3.
3. Use Cap Screws A to fix the
Table Top A onto the unit.
See fig. 3.
D
A
fig. 2
fig. 3
Care and Maintenance
A
fig. 3
Safety
To avoid any risk of suffocation to animals or children dispose of the plastic
bags immediately.
Cleaning
As with all surfaces clean with a damp cloth and mild detergent, do not use bleach
or abrasive products.
Fitting
From time to time please ensure there are no loose screws on the product.
Loading...