Argos Elford - 3 Door Centre Mirror Wardrobe ASSEMBLY INSTRUCTIONS

Page 1
Elford - 3 Door Centre Mirror W ardrobe
Assembly Instructions - Please keep for future reference 240/9142
248/3663 257/4785
Dimensions
Width - 122.2cm Depth - 53.6cm Height - 196cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6403030
Page 2
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor.
• Parts of the assembly will be easier with 2 people.
• Due to difference in floor levels, doors may not be aligned. Adjustment may be necessary.
• To prevent bowing of shelves do not over load, and always distribute weight evenly.
• If a residual aroma is experienced with your new furniture after the packaging is removed simply ensure the room is well ventilated and this will assist a speedy removal
• We do not recommend the use of power drill/ drivers for inserting
screws, as this could damage the unit. Only use hand screwdrivers.
• Dispose of all packaging carefully and responsibly.
• It is essential that this unit be fixed to a wall with the fittings provided.
• Please retain the product label on the back of the unit, as this information will help support any queries.
Care and maintenance - Non compliance with this information may affect your guarantee
• Dust with a clean cloth or, if required a slightly damp cool cloth. Do not use household cleaners, abrasives or polishes as permanent damage may occur.
• Do not drag the furniture or lift it by its top.
• Avoid sharp objects, contact with water and direct heat on all surfaces
Handy Hints
• Assemble all parts and bolts loosely during assembly, only once the product is complete should you fully tighten the bolts.
• Your furniture is finished to the required colour. Avoid exposure to strong sunlight as this can change the colour. Change in appearence may also occur if items are permanently left on a surface.
• Doors should be secured or removed before moving.
• Regularly check and ensure that all boths and fittings are tightened properly.
• You should get assistance when moving or lifting your furniture. Furniture consisting of more than one unit should be disassembled before attempting to move it.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
1
Page 3
If you have damaged or missing components, call the
Components - Panels
Customer Helpline:
Please check you have all the panels listed below
Argos = 0345 6403030
Double wardrobe (191 x 82.2 x 53.6cm)
1
3
Cornice
(122.2 x 5cm)
Single wardrobe
2
(191 x 42.2 x 53.6cm)
2
Page 4
Components - Fittings
Please check you have all the fi ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fi ttings may be supplied than are required.
A
15mm Screw x 1
D
20mm Cornice screw x 9
B
15mm Washer x 2
E
13mm Cornice screw x 2
C
F
18mm Conecting bolt x 2
G
Threaded sleeve x 2
The following components are pre-fi tted and are illustrated for reference only.
Bar handle x 2
22mm Handle screw x 4
Angle bracket x 2
Tools required
Phillips screwdriver (medium)
Wall strap x 1
Step ladder (or equivalent)
Ruler - Use this ruler to help correctly identify the screws
105
0 5 10 15 20 25 30 35 40 45 50
55 60
65 70 75 80
85 90 95 100
110 115 120 125 130 135 140 145 150
155 160
165 170
The screws length is measured from the head to the point (30mm screw shown) .
3
Page 5
Assembly Instructions
Step 1
Position and connect the units
a: Before connecting the
units you will fi rst need to remove all doors.
Loosen but do not remove bolt B in the centre of the hinge back plates which are attached to the wardrobe side panel.
Slide the door off the back plates allowing bolt B to go through the key hole.
a:
A
B
A
C
b: Position the double
1
wardrobe required position [please note it will be hard to move once connected]. Once in place position the single wardrobe along side so the the front edges are aligned.
To fi x the two units together you will need two 18mm connecting
F
bolts Threaded sleeves
Thread 18mm connecting
F
bolt top hole inside the double wardrobe then screw threaded sleeve
G
through from inside
single wadrobe.
in the
and two
through the
2
G
.
b:
WARNING: Help may be required for this step.
F
1 2
G
Repeat for bottom hole
4
Page 6
Assembly Instructions
Step 2
Re-fi tting the doors
Starting from the top, slide the keyhole shaped groove in the hinge over bolt B on the hinge plate.
Once located tighten bolt B and move on to the next hinge.
A
B
A
C
Step 3
Remove and replace handles
a: The bar handles are
tted to the inside of the unit, using a Philips screwdriver unscrew the 22mm handle screws in each handle and remove both the 22mm handle screw and the bar handle.
a:
1
2
Philips
screwdriver
22mm Handle screw
Continued on next page.
5
Page 7
Assembly Instructions
Step 3 - continued
b: Replace the bar
handle on the front of the unit. Fix in position by screwing the 22mm handle screw into each bar handle from inside the unit using a Philips screwdriver.
Note: Only use the 20mm handle screw that the handles were pre­ tted with.
b:
Bar handle
22mm Handle screw
Philips screwdriver
1
2
Step 4
Fitting the cornice
a: Place the cornice
on top of the wardrobe. ensure the the back of the cornice lines up with the back of the pilaster and that each end lines up with the edge of the pilaster.
When in position fi x in place using the 20mm cornice screw pre drilled hole in the cornice screwdriver.
Note: There are not any pre-drilled holes in the top of the robe for this.
D
3
and a philips
3
the
a:
Philips screwdriver
D
3
1
2
Pilaster
Continued on next page.
6
Page 8
Assembly Instructions
Step 4 - continued
b: When fi xed in place
fully secure by screwing the13mm cornice
E
screws angle brackets in to the wardrobe using a philips screwdriver.
Note: There are not any pre-drilled holes in the top of the robe for this.
through the
b:
Angle bracket
1
3
2
Step 5
Fixing to wall
It is recommended that the wardrobe is fi xed to a wall
C
Fix wall strap top of wardrobe using 15mm screw 15mm washer
Warning: The
15mm screw
is for fi xing the wall strap only. In addition to this you will need to choose a screw or fi tting which is suitable for securing the wall strap of walls you have. If you are unsure about what type of screw to use seek professional help.
to the
A
and
B
.
C
to furniture
C
to the type
A
Using the correct type of screw
screw through the washer and wall
strap into a pre-drilled hole in the
wall
A
B
B
C
7
Page 9
Assembly Instructions
Step 6
Adjusting doors
1. To adjust the height / level of the door loosen all screw ‘A’s on all hinge plates, level the door height and retighten all screw ‘A’s.
2. To adjust the gap between the doors loosen screw ‘B’, then turn screw ‘C’ clockwise to close the gap or anticlockwise to increase the gap. Re-tighten screw ‘B’ to lock position.
3. To adjust the distance away from the unit loosen screw ‘B’, this allows the hinge arm to slide back and forth. Adjust as required then re-tighten screw ‘B’.
A
B
A
C
2
1
3
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6403030
Loading...