MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Eden - Low Sideboard TV Unit
Assembly Instructions - Please keep for future reference
413/1267
392/8330
Width - 119.5cm
Depth - 38.1cm
Height - 63.1cm
Issue 1 - 23/07/15
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 25kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
1 2 3 4
5 6
7 8
Left Side (DF3286)
(59.6 x 37.8cm)
Right Side (DF3283)
(59.6 x 37.8cm)
Left Divider (DF3285)
(53.1 x 34.9cm)
Right Divider (DF3281)
(53.1 x 34.9cm)
Small Shelf (DF3288)
(32 x 34.8cm) x 2
Middle Shelf (DF3287)
(44.4 x 34.8cm) x 2
Left Door (DF3284)
(52.6 x 36.9cm)
Right Door (DF3986)
(52.6 x 36.9cm)
Back (X1137-574)
(113.7 x 57.4cm)
9 10
11
Top (DF3099)
(119.5 x 38.1cm)
Base (DF4002)
(111.9 x 37.2cm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
D E F
G H I
LJ
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
19mm Screw (F461) x 4
13mm Screw (F63) x 8
Door stop (F110) x 16
Hinge plate
(F523) x 4
Hinge (F522) x 4
B
Large locking
nut (F900) x 8
A
Metal dowel (F901) x 8
Nail (F51) x 25
Wooden dowel (F22) x 4
J
Small metal dowel (F893) x 8
K
C
Hollow core
locking nut
(F892) x 8
Handle (F414) x 2
C
C
Assembly Instructions
4
Step 1
Step 2
Prepare the top
Screw 4 metal dowels
into the top .
Screw 4 small metal
dowels into the top
. .
Note: Tighten both lots
of metal dowels up fully
against the panels.
J
5
J
J
J
J
A
A
A
A
A
J
A
5
5
Finished
front edge
B
B
B
Prepare the left
divider
Insert 4 large locking
nuts into the
left divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the left divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
B
B
Finished
front edge
10mm
C
B
3
C
3
3
Finished
front edge
Finished
front edge
C
C
Finished
front edge
Finished
front edge
Assembly Instructions
5
Step 3
Step 4
Fit the left divider to
the top
Push the left divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
3
B
B
3
A
B
5
3
Prepare the right
divider
Insert 4 large locking
nuts into the
right divider .
Tap 2 wooden dowels
into the right divider .
Step 5
B
4
C
4
B
B
B
B
4
Fit the right divider
Push the right divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right divider .
5
4
B
4
5
4
Finished
front edge
Assembly Instructions
6
Step 6
K
K K
Prepare the base
Push 4 hollow core
locking nuts into the
base , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Turn the base over
Screw 4 metal dowels
into the base .
K
K
6
K
A
6
K
K
K
K
Finished
front edge
6
Fit the base
Push the base onto
the left divider and
right divider .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left divider and
right divider .
3
4
6
B
3
4
Step 7
3
4
6
Turn the
base over
A
A
A
A
Finished
front edge
6
Finished
front edge
Assembly Instructions
7
Step 8
H
Prepare the left side
Push 2 hollow core
locking nuts into the
left side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Screw 2 small metal
dowels into the left
side .
Fit 2 hinge plates onto
the left end , making
sure that the slot is
facing towards the
finished front edge.
K
K
1
J
1
H
1
K
K
H
H
J
J
1
Step 9
Prepare the right side
Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Screw 2 small metal
dowels into the right
side .
Fit 2 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
K
K
2
J
2
H
2
H
H
K
K
J
J
H
Finished
front edge
2
Finished
front edge
Assembly Instructions
8
Step 10
Step 11
Fit the right side
Push the right side
onto the top and
base .
The 2 small metal
dowels fitted to
the right side
must slide into the 2
hollow core locking
nuts fitted to the
base and the 2 small
metal dowels fitted to
the top must slide
into the 2 hollow core
locking nuts fitted to
the right side .
Insert a screwdriver into
the 4 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
J
K K
2
6
5
J
2
K
6
J
5
K
K
2
2
6
5
Fit the left side
Push the left side
onto the top and
base .
The 2 small metal dowels
. fitted to the left side
must slide into the 2
hollow core locking nuts
. fitted to the base
and the 2 small metal
dowels fitted to the
top must slide into
the 2 hollow core locking
nuts fitted to the left
side .
Insert a screwdriver into
the 4 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
1
5
J
1
K
6
J
5
K
K
1
6
1
6
5
yy
xx
yy
Assembly Instructions
9
Step 12
Step 13
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
11
F
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
11
Warning: The
unit is heavy.
Lift with care.
xx
b:
F
11
Fit the middle shelves
Insert 4 shelf studs for
each of the 2 middle
shelves at the
required height.
Lower the 2 middle
shelves down onto
the shelf studs .
G
G
x 4
G
x 4
8
8
G
8
8
Assembly Instructions
10
Step 14
G
x 4
Fit the small shelves
Insert 4 shelf studs for
each of the 2 small
shelves at the
required height.
Lower the 2 small
shelves down onto
the shelf studs .
G
7
7
G
G
x 4
7
7
Prepare the 2 doors
Push fit 2 hinges into
each of the 2 doors
and .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
E
I
9
10
90
I
Step 15
I
E
E
I
E
E
I
E
E
I
E
E
9
10
Assembly Instructions
11
Step 16
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
bottom hinge.
a: Push the hinge
onto the front part of the
hinge plate .
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each of the 2 doors
and using screws .
I
I
I
H
H
H
I
H
L
D
9
10
a: b:
c: d:
H
I
H
H
B
H
I
I
I
A
I
H
B
e:
9
10
L
D
D
L
10
9
12
Step 17
Assembly Instructions
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Assembly Instructions
13
Step 18
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Assembly is complete
ALR3159
Loading...