MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Eden - 3+2 Sideboard
Assembly Instructions - Please keep for future reference
391/7066
414/4034
Width - 119.5cm
Issue 1 - 21/07/15
Depth - 38.1cm
Height - 83.2cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 42kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Drawer Front (DF3047)
(36.9 x 24cm) x 2
Middle Drawer
Base (T317-327)
(31.7 x 32.7cm)
Drawer Base
(T353-327)
(35.3 x 32.7cm) x 2
Middle Drawer
Back (W306-195)
(30.6 x 19.5cm)
Drawer Back (W342-195)
(34.2 x 19.5cm) x 2
Left Drawer
Side (W330-195LH)
(33 x 19.5cm) x 3
Right Drawer
Side (W330-195RH)
(33 x 19.5cm) x 3
Middle Drawer
Front (DF3048)
(36.9 x 24cm)
1 3 42
5 6
7 8
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
9 10 11
Shelf (DF4014)
(55.2 x 34.8cm) x 2
Left Side (DF4322)
(79.7 x 37.8cm)
Right Side (DF4321)
(79.7 x 37.8cm)
Top Divider (DF1241)
(23.7 x 34.9cm) x 2
12
Bottom Divider (DF4015)
(48 x 34.9cm)
Horizontal Divider (DF3045)
(111.9 x 35cm)
Top (DF3043)
(119.5 x 38.1cm)
Base (DF4323)
(111.9 x 37.2cm)
Left Door (DF4324)
(48.3 x 55.5cm)
Right Door (DF4013)
(48.3 x 55.5cm)
Back (X1137-762)
(113.7 x 76.2cm)
13 14
15 16
17 18
19
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
B
D E F
G H I
C
R
K L
Small metal dowel (F893) x 8
Hollow core
locking nut
(F892) x 8
Wooden dowel (F22) x 10
J
N
T
13mm Screw (F63) x 8
Knock-in Peg (F171GY) x 12
9mm Screw (F74) x 6 9mm Screw (F73) x 12
Drawer runner (F1004) x 6
Wedgefix (F639) x 6
Large locking
nut (F900) x 12
A
Metal dowel (F901) x 18
M
QO P
Shelf stud (F110) x 8
Hinge plate
(F523) x 4
Hinge (F522) x 4
Small locking
nut (F3) x 6
19mm Screw (F461) x 10
Handle (F414) x 5
S
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
40mm Screw (F910) x 4
Nail (F51) x 25
1
Assembly Instructions
4
Step 1
A
B
A
C
C
C
C
3
4
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
1
Prepare 2 pairs of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
3
4
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
3
4
1
C
C
4
3
A
A
1
3
4
x 2
x 2
x 2
x 2
2
2.5cm
0.7cm
1
Assembly Instructions
5
Step 4
E
E
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
7
3 4
1
10
3 4
7
5
5
E
4
3
7
4
5
7
3
E
E
Step 6
Step 7
Fit the wedgefixes
Turn the 2 drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
F
F
F
F
x 2
x 2
x 2
x 2
Attach the handles
Attach the handle to
each drawer front
using screws .
G
1
R
G
G
R
Drawer Base
(T353-327)
(35.3 x 32.7cm) x 2
Middle Drawer
Base (T317-327)
(31.7 x 32.7cm)
3 4
1
Middle Drawer
Back (W306-195)
(30.6 x 19.5cm)
Drawer Back
(W342-195)
(34.2 x 19.5cm) x 2
2
2
6
Step 8
A
B
A
C
C
C
C
3
4
Step 9
Prepare the middle
drawer front
Screw 2 metal dowels
into the middle drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
A
2
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 10
C
3
4
Attach the drawer
sides to the middle
drawer front
Push the left drawer side
. and right drawer side
. onto the back of the
middle drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
3
4
2
C
C
4
3
A
A
3
4
Assembly Instructions
2
2
Assembly Instructions
7
Step 11
E
E
Fit the middle drawer
base
Slide the middle drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the middle drawer front
. .
Step 12
Fit the drawer back
Fit the middle drawer
back between the
drawer sides and .
Make sure that the
middle drawer base
fits into the groove in the
middle drawer back .
Hold the middle drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
8
3 4
2
6
3 4
8
6
6
E
4
3
8
4
6
8
3
E
E
Step 13
Step 14
Fit the wedgefixes
Turn the middle drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
F
F
F
F
Attach the handle
Attach the handle to
the middle drawer front
using screws .
G
2
R
G
G
R
3 4
2
D
D
D
D
8
Step 15
Assembly Instructions
B
B
B
B
Prepare the horizontal
divider
Screw 2 metal dowels
into the horizontal divider
. .
Insert 4 large locking
nuts into the
horizontal divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 4 wooden dowels
into the horizontal divider
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
15
15
15
A
A
B
15
D
10mm
D
D
B
D
Finished
front edge
B
B
B
B
Prepare the bottom
divider
Insert 4 large locking
nuts into the bottom
divider .
Tap 2 wooden dowels
into the bottom divider
. .
11
11
B
D
Step 16
Finished
front edge
11
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 17
Step 18
Fit the bottom divider
to the horizontal
divider
Push the bottom divider
. onto the horizontal
divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the bottom divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
15
11
B
B
11
A
B
15
11
L
L L
Prepare the base
Push 4 hollow core
locking nuts into the
base , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
Turn the base over
Screw 2 metal dowels
into the base .
L
L
14
L
A
14
Turn the
base over
L
L
L
L
A
A
Finished
front edge
Finished
front edge
14
14
10
Step 19
Assembly Instructions
D
D
Finished
front edge
Finished
front edge
I
N
I
d:
e:
a:
b:
c:
I
N
I
N
I
N
Finished
front edge
Finished
front edge
I
B
B
Finished
front edge
Turn the top
divider over
Prepare the 2 top
dividers
a: Place a runner on
each top divider as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the top dividers .
c: Insert 2 large locking
nuts into the top
dividers .
Tap 2 wooden dowels
into the top dividers .
Turn the top divider over
a: Place a runner on
each top divider as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the top dividers .
12
I
I
12
12
12
N
N
12
I
I
12
N
N
B
D
Note: Due to the
manufacturing process,
the 2 holes for the large
locking nut can be on
either surface of the top
divider.
x 2
x 2
x 2
x 2
x 2
12
12
12
12
12
Finished
front edge
M
Assembly Instructions
11
Step 20
Step 21
15
12
Fit the 2 top dividers
Attach the 2 top dividers
. to the horizontal
divider using 4
screws .
M
M
M
12
12
12
M
Finished front edge
Fit the base
Push the base onto
the bottom divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the bottom divider .
11
14
B
11
Step 22
Prepare the top
Screw 4 metal dowels
into the top .
Screw 4 small metal
dowels into the top .
A
13
K
13
Finished
front edge
K
K
K
K
A
A
A
A
13
11
14
Finished
front edge
Finished
front edge
Finished
front edge
Finished front edge
12
Step 23
Assembly Instructions
Fit the top
Push the top onto
the 2 top dividers .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the 2 top dividers .
12
13
B
12
12
12
13
I
N
I
L
K
L
K
A
A
Prepare the left side
a: Place a runner on
the left side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 2 metal
dowels into the left
side .
Screw 2 small metal
dowels into the left
side .
Push 2 hollow core
locking nuts into the
left side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
9
I
I
9
N
N
a:
b:
c:
O
Step 24
O
O
A
9
9
K
L
L
9
O
9
9
9
9
Assembly Instructions
13
Step 25
Prepare the right side
a: Place a runner on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 2 metal
dowels into the left
side .
Screw 2 small metal
dowels into the right
side .
Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
10
I
I
10
N
N
a:
b:
c:
I
N
A
10
K
10
L
L
10
O
10
I
N
I
L
L
K
K
O
O
O
A
A
Finished
front edge
Finished
front edge
Finished
front edge
10
10
10
14
Step 26
Assembly Instructions
Step 27
K
L L
Fit the base to the
right end
Push the right side
onto the assembly.
The small metal dowels
. fitted to the right side
. and top must
slide into the top of the 4
hollow core locking nuts
. fitted to the right side
. and base . .
Insert a screwdriver into
the 4 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal divider .
10
K
10 13
L
10 14
L
B
15
10
13
14
15
13
14
15
9
Fit the base to the
right end
Push the left side
onto the assembly.
Insert a screwdriver into
the 4 hollow core locking
nuts fitted to the left
side and base
and turn the nuts inside
as far as they will go.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal divider .
L
B
9
15
9 14
yy
xx
yy
Assembly Instructions
15
Step 28
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
19
T
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
19
Fit the drawers
Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
wrap with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
H
N
N
H
2nd threaded
hole
N
H
3 4
Step 29
Warning: The
unit is heavy.
Lift with care.
xx
b:
T
19
H
H
2
1
1
3
4
16
Step 30
Assembly Instructions
Q
x 4
Q
x 4
Fit the shelves
Insert 4 shelf studs for
each shelf .
Lower the shelves
down onto the shelf
studs .
Q
16
16
Q
16
16
Prepare the 2 doors
Push fit 2 hinges into
each of the 2 doors
and .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
J
P
17
18
90
P
Step 31
P
J
J
P
J
J
P
J
J
P
J
J
17
18
R
Assembly Instructions
17
Step 32
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
bottom hinge.
a: Push the hinge
onto the front part of the
hinge plate .
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each of the 2 doors
and using screws .
P
P
P
O
O
O
P
O
R
G
17
18
a: b:
c: d:
O
P
O
O
B
O
P
P
P
A
P
O
B
e:
17
18
G
G
R
17
18
18
Step 33
Assembly Instructions
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C
Assembly Instructions
19
ALR3157
Step 34
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Fit the overbalance
protector kit
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of the
overbalance protector kit
. to the unit, or an
alternative fixing method
of your choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Assembly is complete
S
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
S
S
Example
Screw
(not supplied)
Washer
Screw
UNIT
Loading...