Ohio OttomanC CCCCCCCCCCCCCCCCCCCCCCoffee Table- Ottoman
Assembly Instructions
- Please keep for future reference
143/6563
173/6029
Dimensions
Width - 39cm
Depth - 39cm
Height - 37.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 11/10/13
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Do not discard any of the
packaging until you have
checked that you have all the
parts.
• Check you have all the
components listed on page 2.
• Remove all components from
the plastic bags and separate
them into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
Warnings
• This product should only be
used on firm, level ground.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Assemble this product on a flat
surface.
• Make sure the base remain in
contact with the ground.
• Unit weight: 2.94kgs.
• Maximum safe weight of user:
110kgs.
• Dispose of all packaging
carefully and responsibly.
• Retain Assembly Instructions
for future reference.
• Do not stand on the product.
Care and maintenance
• Please clean this product
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Do not use any abrasive
materials when cleaning.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
If you have damaged or missing components,
Components - Parts
call the Customer Helpline: 08456 400800
Please check you have all the parts listed below
1 Bottom panel
Top cover
(39 x 39 x 5cm)
Seat frame
3
(36 x 36 x 36cm)
2
(35.5 x 36cm)
2
Assembly Instructions
Step 1
Opening seat frame
Open the folded seat
frame by pulling from the
side edge as shown.
3
Step 2
Attaching bottom panel
Use the handle on the
bottom panel to hold
it, then insert it inside the
seat frame and
carefully push it down
into the bottom as
shown.
2
3
3 3 3
handle
2
Step 3
Attaching top cover
Carefully fit top cover
on the seat frame as
shown.
1
3
3
1
3
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
3
Ohio Ottoman Oak Coffee Table
Assembly Instructions - Please keep for future reference
173/6029
Dimensions
Width - 79cm
Depth - 79cm
Height - 43.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 26/10/13
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Warnings
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Unit weight: 18.3kgs.
• At least 2 people are required
to assemble this product.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Dispose of all packaging
carefully and responsibly.
• Retain Assembly Instructions
for future reference.
• This product should only be
used on firm, level ground.
Care and maintenance
• Please clean this product
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Make sure the legs remain in
contact with the ground.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.
• Do not stand on the product.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
If you have damaged or missing components,
Components - Parts
call the Customer Helpline: 08456 400800
Please check you have all the parts listed below
1 Long Base Panel
Table Top
(79 x 79 x 2.5cm)
2
(78.5 x 40.5 X 2.5cm)
Short Base Panel x 2
3
(38 x 40.5 x 2.5cm)
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Bolt x 12
D
B
Cam Lock x 12
E
C
Short Wooden Dowel x 8
Long Wooden Dowel x 2
Adhesive Pad x 12
Tools required
Crosshead Screwdriver
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
2
Assembly Instructions
Step 1
Base panels assembly
a: Insert bolts into
A
holes on long base panel
2
as shown and tighten
using a crosshead
screwdriver.
b: Insert long wooden
dowels into holes on
short base panels .
D
3
b:
a:
A
A
2
a
A
D
D
3
3
D
2
A
c: Insert cam locks
B
into holes on short base
panels .
3
d: Attach the short base
panels to long base
panel aligning the
dowels and bolts with the
cam locks as shown.
3
2
e: Then lock using a
crosshead screwdriver by
turning the cam locks
clockwise.
B
c:
3
2
B
d:
3
B
2
A
A
D
B
3
B
D
2
A
B
e:
3
D
A
B
Lock
3
B
2
3
2
Assembly Instructions
A
A
2
Step 2
Attaching the table top
a: Place the table top
1
upside down on a flat
protected surface.
Insert bolts into holes
on the table top as
A
1
shown and tighten using
a crosshead screwdriver.
b: Insert short wooden
dowels into holes on
long & short base panels
2
& .
c: Insert cam locks
into holes on long & short
base panels & .
d: Attach the table top
onto the base panels
aligning the dowels and
bolts with the cam locks
as shown.
C
3
B
2
3
1
e: Then lock using a
crosshead screwdriver by
turning the cam locks
clockwise.
B
a:
b:
A
1
2
C
c: d:
A
A
A
1
2
B
e:
3
3
2
B
B
1
Lock
1
A
A
2
C
B
A
2
B
B
B
1
f: Remove backing from
adhesive pads and
paste it on the base
panels & to cover
2 3
the cam locks.
Carefully turn over the
table and place on a flat
surface.
Assembly is complete.
E
3
E
3
E E
E
2
E
E
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
f:
3
E
4
Loading...