Page 1
Double Robe
Assembly Instructions - Please keep for future reference
1947090
256002
Dimensions
Width - 100cm
Depth - 57,6cm
Height - 190cm
Important - Please read these instructions fully before starting assembly
For all enquiries please contact : 08456 400800
Ref. no RY 01.00 Date: 14/02/14
Page 2
Safety and care advice
Important -
• Check you have all the
components and tools listed on
pages 3 and 4.
Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels, this could cause
damage.
Please read these intructions fully before starting assembly
• Assemble the unit as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
We do not
•
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Warning: Before drilling,
check the wall for hidden pipes
and cables.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately
Please lift with care.
70kgs
Care and maintenance
• From time to time check that
there are no loose screws on
this unit.
Cleaning instructions
• This product has been
manufactured using modern
manufacturing methods and
materials. With appropriate
in-home care and maintenance it will provide trouble
free performances.
domestic multi-purpose
cleaning agents are unsuitable
for use on this product.
Many
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
The use of aggressive chemicals can result in irreversible
damage. Please follow these
guidelines carefully.
USE only 5% soap, 95%
water solution, wiping with a
damp (not wet) cloth. Finally
dry with a soft clean cloth.
Dust with a soft clean cloth
only.
DO NOT USE wax furniture
polish, abrasive or aggressive
cleaners, bleach or hypochlorate (chlorine) based cleaners,
multi-purpose cleaners,
dilutes, acetone, alcohol,
solvent or similar products.
Recycling – the packaging materials for this product may
be recycled through your local recycling centre. When you
want to dispose of the product itself, please consider
donating it to a local charitable organisation, otherwise
recycle it through your local recycling centre.
2
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Page 3
Components - Panels
Please check you have all the panels listed below
1) Left end panel x1
2) Right end panel x1
3) Back panel x1
4) Top panel x1
5) Top frame x1
6) Left frame x1
7) Right frame x1
8) Shelf x1
9) Bottom x1
10) Doors x2
1
5
4
2
3
7
8
10
10
9
6
3
Page 4
Wooden dowel x 12
Ruler -Usethis ruler to help correctly identify the screws
Tools required
A
E
Metal dowel x 12
B
Spacer x 1
15mm Screw x 10
C
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittingsmay be supplied than are required.
05101520253035404550556065707580859095100
110 115 120 125 130 135 140 145 150 155 160 165170
105
F
D
K L
G
M ON
25mm Nail x 40
x 1
H
Long locking
nut x 12
00203040506070809000 020304050
0
23456
Phillips screwdriver
(medium & large)
Spirit level
Flatbladescrewdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Ø 5mm Suitable drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
mm
4MAx25 Screw x 2
Glue x 1
Components - Fittings
Please check you have all the fittings listed below
P
Wedgefix housing x 12Wedgefix dowel x 12
Sticker felt pads x 6
Door stop x 1
C
T
R
clip hinge x 6 and 15mm Screw x 12
hinge mounting plate x 6
Q
Door stop x 1
Hanger rail
support x 2
J
hanging rail x 1
Knob x 2
4
Page 5
Assembly Instructions
Step 1
Top
Top
Bottom
Bottom
1
2
5
E
E
E
E
A
K
K
K
A
C
C
N
N
T
T
T
E
A
K
K
K
6
7
L
L
L
NO
NO
YES
YES
5
Page 6
Assembly Instructions
Step 2
8
L
L
9
I
C
B
I
C
4
B
C
Q
C
Q
6
Page 7
Assembly Instructions
Step 4
Step 3
1
2
5
4
9
E
6
7
A
A
A
M
7
Page 8
Assembly Instructions
Step 5
Step 6
8
8
6
5
7
5
C
O
Q
8
Page 9
Assembly Instructions
Step 7
Step 8
Turn over
Fixing back panels
b:
a:
3
D
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
9
Page 10
Assembly Instructions
Step 9
Stand up
10
Page 11
A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.
Page 12
Assembly Instructions
Step 10
Wall fixing
H
F
C
H
WALL PLUG
AND SCREW
NOT INCLUDED
Please see
Guide to
wall mounting
2
0
m
m
F
C
12
Page 13
Assembly Instructions
Step 11
Hanging rail positioning
Step 12
Application of hinges to door
RH
LH
J
J
R
C
R
C
13
Page 14
Assembly Instructions
Step 13
Hang door
Step 14
Door adjustment
A
B
C
A
B
C
G
P
CLICK
PUSH
a:
b:
c:
R
T
T
T
R
R
14
Page 15
Assembly Instructions
Recycling – the packaging materials
for this product may be recycled
through your local recycling centre.
When you want to dispose of the
product itself, please consider
donating it to a local charitable
organisation, otherwise recycle it
through your local recycling centre.
CLEANING INSTRUCTIONS
This product has been manufactured using
modern manufacturing methods and
materials. With appropriate in-home care
and maintenance it will provide trouble free
performances. Many domestic multipurpose cleaning agents are unsuitable for
use on this product. The use of aggressive
chemicals can result in irreversible
damage. Please follow these guidelines
carefully.
USE only 5% soap, 95% water solution,
wiping with a damp (not wet) cloth. Finally
dry with a soft clean cloth. Dust with a soft
clean cloth only.
DO NOT USE wax furniture polish, abrasive or aggressive cleaners, bleach or
hypochlorate (chlorine) based cleaners,
multi-purpose cleaners, dilutes, acetone,
alcohol, solvent or similar products.
That's the Robe completed.
Take care of your unit by using a damp cloth to clean it.
Please remember to occasionally check that all Cams
and Screws are tight.
15
Page 16
Loading...