Argos Designer 2 Tone - TV Unit ASSEMBLY INSTRUCTIONS

Page 1
MADE IN
BRITAIN
Dimensions
Width - 113.5cm
Depth - 40cm
Height - 61cm
Designer 2 Tone - TV Unit
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 02/07/14
Important - Please read these instructions fully before starting assembly
249/8593
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 29.5kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Flyover Top (D2968A)
(900 x 396mm)
Left Side (D2970A)
(398 x 395mm)
Small Upright (D2974A)
(146 x 280mm)
Fixed Shelf (D2976A)
(218 x 329mm)
Base (D2977A)
(1133 x 396mm)
Right Side (D2973A)
(559 x 395mm)
Top (D2969A)
(900 x 396mm)
Loose Shelf (D2975A)
(492 x 390mm) x 2
3
7
4
Left Upright (D2971A)
(398 x 395mm)
Right Upright (D2972A)
(398 x 395mm)
Drawer Front (D2978A)
(355 x 194mm) x 2
Drawer Base (T337-367)
(337 x 367mm) x 2
Back (X826-424)
(826 x 424mm)
Drawer Back (W326-124)
(326 x 124mm) x 2
Left Drawer Side (W370-124LH)
(370 x 124mm) x 2
Right Drawer Side (W370-124RH)
(370 x 124mm) x 2
2
5
10 11
8
9
6
12
13
14 15 16
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A B
Metal dowel (F901) x 14
C
D E
Large locking nut (F900) x 10
F
H I
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
25mm Screw (F50) x 9
G
J
40mm Screw (F910) x 8
P
Drawer runner (F1004) x 4
9mm Screw (F74) x 4
Knock-in Peg (F171GY) x 8
Nail (F51) x 179mm Screw (F73) x 8
L
Shelf stud (F110) x 8
K
M
N
Wedgefix (F639) x 4
Handle (F930) x 2
Feet (F854) x 5
O
Shelf stud (F372) x 4
Mini Block (F25) x 2
Page 5
11
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
x 2
B
B
B
C
C
C
C
13
14
Step 2
Prepare the 2 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
11
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
13
14
Attach the drawer sides to the drawer fronts
Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
13 14
11
C
C
13 14
13
14
B
B
11
Page 6
11
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
15
13 14
11
12
13 14
15
12
12
J
Attach the handles
Attach a handle to each of the drawer fronts . using 2 screws .
Note: Do not overtighten the screws.
M
F
11
13 14
Step 7
Fit the wedgefixes
Turn the drawer assemblies over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
K
x 2
x 2
x 2
J
J
x 2
K
K
K
15
13
12
13
14
15
14
M
F
F
11
Page 7
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
Prepare the top
Screw 6 metal dowels into the top .
B
1
B
B
B
B
B
B
Finished
front edge
1
Insert 2 large locking nuts into the right upright .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
D
D
Step 9
Step 10
D
5
Finished
front edge
5
Fit the right upright to the top
Push the right upright onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the right upright .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
1
5
D
D
5
B
D
1
5
Page 8
Assembly Instructions
7
Step 11
Step 12
Finished
front edge
Finished
front edge
Prepare the left upright
Note: Do not use the through holes to fit the runners.
a: Place 2 runners on
the left upright as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left upright .
Insert 2 large locking nuts into the left upright .
4
H
H
4
P
P
D
4
Finished
front edge
H
P
H
H
H
P
H
P
a:
b:
1
Finished
front edge
Fit the left upright
Push the left upright onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the left upright .
1
4
D
4
4
4
4
D
D
5
Page 9
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 13
Step 14
Fit the left side
Push the left side onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the left side .
1
Prepare the left side
a: Place 2 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
Insert 2 large locking nuts into the left side . .
a:
b:
H
H
Finished
front edge
H
P
H
P
H
P
3
H
H
3
P
P
D
3
1
3
D
3
3
D
D
3
3
Page 10
Assembly Instructions
9
Step 15
Step 16
Finished
front edge
Fit the base
Attach the base to the assembly using 6 screws .
E
E
E
E
E
plain chipboard surface
7
7
E
Prepare the base
Screw the 5 feet onto the base using screws .
F
N
F
N
N
7
F
F
N
F
N
Finished
front edge
plain chipboard surface
7
F
N
E
Page 11
Assembly Instructions
10
Step 17
Step 18
yy
xx
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit, as shown.
Nail around the 3 edges of the back , as shown.
Note: Nails should be spaced about 150mm apart.
16
I
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
16
yy
xx
Note:
This gap is for
cable management.
I
16
Prepare the right side
Insert 2 large locking nuts into the right side .
D
6
D
D
Finished
front edge
6
Page 12
Assembly Instructions
11
Step 20
Step 19
6
Secure the right side
Attach the right side to the base using 2 screws .
Carefully stand the unit up for the next step.
E
E
6
7
E
7
Warning: The unit is heavy. Lift with care.
D
Prepare the small upright
Insert 2 large locking nuts into the small upright .
Gently tap the 2 mini blocks into the holes in the small upright orientated as shown.
D
10
10
D
A
10
A
A
Step 21
B
Finished
front edge
B
Prepare the flyover top
Screw 2 metal dowels into the flyover top .
B
2
2
A
Page 13
Assembly Instructions
12
Step 22
Step 23
Finished
front edge
2
10
Fit the small upright to the flyover top
Position the small upright so that the screws from the mini blocks are over the holes in the flyover top . .
Tighten up the screws in the 2 mini blocks into the holes in the flyover­top .
10
A
2
A
2
1
B
Fit 2 metal dowels to the top panel
Screw 2 metal dowels into the top panel as shown.
Note: Tighten the metal dowels up fully against the panels.
B
1
B
B
A
10
2
Page 14
Assembly Instructions
13
Step 24
Fit the flyover top assembly
Lower the flyover top and small upright down onto the unit as shown.
Use a screwdriver to tighten the 4 large locking nuts fitted to the right side and small upright .
D
2
10
6
2
10
6
Finished
front edge
10
Step 25
6
Fit the fixed shelf
Push 4 shelf studs for the fixed shelf into the right side and right upright .
Lower the fixed shelf down onto the shelf studs and tighten the screws up into the bottom of the shelf.
O
x 4
O
O
9
6
5
5
9
9
O
Page 15
Assembly Instructions
14
Step 26
L
x 4
Fit the shelf studs
For each of the 2 loose shelves , insert 4 shelf studs .
L
x 4
L
8
Fit the loose shelves
Lower the 2 loose shelves down onto the shelf studs .
L
8
8
8
Step 27
Page 16
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 28
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws. If they catch on the runner you may need to loosen them slightly.
Assembly is complete
G
P
P
2nd threaded
hole
P
G
13 14
G
G
ALR3049
Loading...