Argos Denver - 3 Door Mirror Robe ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 3 - 13/07/15

Important - Please read these instructions fully before starting assembly

360/2546

359/7596

335/9806

Denver - 3 Door Mirror Robe

Dimensions

Width - 113.5cm

Depth - 50cm

Height - 181cm

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 80kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Tools required

Rule

Scissors

Spirit level

Hammer Bradawl

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Step ladder

Electric drill (only use when drilling into walls)

Square

mm

10

20

30

40

50

60

70

80

90

100

mm

10

20

30

40

50

60

70

80

90

100

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

1 2

3

Shelf (DF2353)

(372 x 470mm) x 3

Left Side (D1575A)

(1808 x 496mm)

Right Side (DF1987)

(1808 x 496mm)

Door

(D1578A)

(1786 x 355mm)

x 2

Vertical Rail

(D1577A)

(1752 x 88mm)

x 2

Small Back

(X1779-391)

(1779 x 391mm)

Large Back

(X1779-737)

(1779 x 737mm)

4

6

Hanging Rail (FHR710)

(710mm long)

7

8 9 11 12

Top/Base (DF1877A)

(1105 x 494mm) x 2

Mirror Door

(D1578MA)

(1786 x 355mm) (Mirror - SG06 1776 x 300mm Safety Back SAR)

10

Horizontal (DF3100A)

(718 x 470mm)

5

Divider (DF2668)

(1753 x 494mm)

Please check you have all the fittings listed below

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 6

B

Metal dowel (F901) x 12

C

D E F

G H

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Large locking nut (F900) x 12

M

I

KJ

Nail (F51) x 38

N

Rail holder

(F1014) x 2

40mm Screw (F910) x 12

13mm Screw (F63) x 20

Hinge (F518) x 9

Hinge plate (F523) x 9

Plastic Nail (F91) x 4

Back holder (F276) x 6

Nail screw (F277) x 6

Shelf stud (F110) x 12

L

Strap

Screw Washer x 2

Overbalance protector kit (F269) x 1

Bracket (F945) x 2

O

P

13mm Screw (F79) x 4

Important: Always pair up the hinges with the hinge plates from the same bag. DO NOT mix them up.

Finished

front edge

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the left side

Screw 6 metal dowels into the left side .

Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

B

1

M

K

F

1

M

1

M

B

M

K

F

1

Prepare the right side

Screw 4 metal dowels into the right side .

Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.

B

2

M

2

B

M

B

2

M

Finished

front edge

Finished

front edge

Finished

front edge

A

Assembly Instructions

5

Step 3

Step 4

Prepare the 2 top and base panels

Tap 2 wooden dowels into each of the top and base panels .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

Insert 4 large locking nuts into each of the top and base panels .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

4

D

10mm

A

x 2

A

4

D

A

D

Finished

front edge

4

Base

Fit the top and base

Push the top and base onto the right side .

Use a screwdriver to tighten the 2 large locking nuts fitted to the top and the 2 large locking nuts fitted to the base .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

4

2

D

4

D

B

D

Finished

front edge

4

Top

2

E

Assembly Instructions

6

Step 5

4

Fit the 2 vertical rails

Attach each of the vertical rails to the top and base using 4 screws .

8

4 4

E

8

E

4

E

Step 6

B

M

Finished

front edge

Prepare the divider

Screw 2 metal dowels into the divider .

Push a rail holder into the divider . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .

Fit 3 hinge plates onto the divider , making sure that the slot is facing towards the finished front edge.

K

F

3

K

F

B

M

3

Finished

front edge

E

Assembly Instructions

7

Step 7

Step 8

4

E

4

3

Fit the 2 divider

Attach the divider to the top and base using 4 screws .

3

4 4

E

4

Prepare the horizontal

Tap 2 wooden dowels into the horizontal .

Insert 4 large locking nuts into the horizontal .

5

D

Finished

front edge

A

5

4

3

5

Step 9

Fit the horizontal

Push the horizontal onto the divider .

Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .

5

3

D

5

Assembly Instructions

8

Step 10

44

4

Fit the left side

Push the left side onto the assembly.

Use a screwdriver to tighten the 6 large locking nuts fitted to the top , base and the horizontal .

1

D

5

4 4

1

5

4

Step 11

Fit the 4 plastic nails

Tap 2 plastic nails into the bottom edge of each of the sides and . .

J

1

2

J

1

2

yy

Assembly Instructions

9

Step 12

4

Fit the back panels

a: Square up the unit by

making sure that measurement x:x equals

y:y.

Place the small back and large back down, onto the unit as shown.

Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the divider’s back edge.

b: Nail around the

outside edges of the 2 backs.

Note: Do not nail where the 2 backs meet and nails should be spaced about 150mm apart.

c: Push the 5 nail

screws through the 5 back holders and tap them down between the small back and large back and into the back edge of the divider . .

Keep tapping the nail screws in until the back holders dig into the small and large back.

Stand the unit up for the next step.

11

12

I

G

H

11

12

3

G

H

The measurement from top corner X to bottom corner X must be

equal to the measurement from top corner Y to bottom corner Y

a:

Note: If ever you need to take the backs off to dismantle the unit, the nail screws can be taken out using a screwdriver.

G

H

c:

G

H

11

12

H

HG

+

b:

I

xx

11

12

Warning: The unit is heavy. Lift with care.

Assembly Instructions

10

Step 13

7

K

Fit the hanging rail and shelves

Push the hanging rail into the rail holders fitted to the side panels.

For each of the 3 shelves , insert 4 shelf studs .

Lower the 3 shelves down onto the shelf studs .

7

K

7

C

x 4

C

x 4

C

x 4

6

C

6

C

Assembly Instructions

11

Step 14

Fit the brackets to the vertical rails

Fit one bracket to the vertical rail and horizontal using screws .

Fit second bracket to the other vertical rail and the divider using screws .

3

P

8

OO

Step 15

90

N

F

N

F

N

F

9

x 2

8

5

8

5

O

P

3

OO

8

P

Prepare the 3 doors

Lay the doors down onto a soft, smooth surface.

Push fit 3 hinges into each plain door and the mirror door .

Secure each hinge with 2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.

F

N

9

10

Warning: Glass! Handle with care

N

F

N

F

N

F

10

x 1

Assembly Instructions

12

Step 16

Fit the 3 doors

Note: The easiest way to attach each door and is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge

onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge

FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.

c: The hinge must be

flat against the hinge plate prior to any adjustment.

d: The hinge must

NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.

N

M

N

M

9

a: b:

c: d:

M

N

M

B

M

N

A

N

M

B

9

10

9

10

Assembly Instructions

13

Step 17

Adjust the doors if needed

a: Before adjusting the

doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.

Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.

c: Forward and Back

adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.

d: Sideways

adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.

b:

c:

d:

a:

A

B

C

Assembly Instructions

14

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Step 18

Fit the overbalance protector

To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.

Wall fixings are not supplied as they will need to suit the wall type.

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Assembly is complete

L

Strap

Washer

Screw

TOP OF UNIT

L

WALL

Wall fixing

(not supplied)

Screw

(not supplied)

Washer

Strap

L

ALR3096

IMPORTANT INFORMATION ABOUT THIS PRODUCT

This product complies with the requirements of BS 7449:1991 and has been

manufactured by

DECORATIVE PANELS FURNITURE LTD, TEESSIDE

INDUSTRIAL ESTATE, THORNABY-ON-TEES, CLEVELAND, TS17 9LT

.

The product code for this unit and the item code(s) for the glass

components are listed in the Assembly Instructions along with a description

of the type of glass used. All clear/tinted glass complies with the

requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer, or agent with regard to

obtaining a manufacturing specification and shape for replacement glass

quoting the unit description and batch number or date of manufacture.

Do not place very hot or very cold items against or in close proximity to

glass surface(s) unless adequately thick insulating material is used to

prevent such items coming in contact with the glass.

Do not strike the glass with hard or pointed items.

Do not sit or stand upon horizontal glass surfaces.

When cleaning glass panels use a damp cloth or leather with washing up

liquid or soft soap if necessary - do not use washing powders or any other

substance containing abrasives since these substances scratch glass.

If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.

KEEP THESE INSTRUCTIONS FOR FUTURE USE