Argos ZDV22R2-WO-AR, Denver - 2 Drawer 2 Door Robe ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 3 - 16/01/15
Important - Please read these instructions fully before starting assembly
Denver - 2 Drawer 2 Door Robe
Dimensions
Width - 75cm
Depth - 50cm
Height - 181cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 52kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
1 2
4
3
Hanging Rail (FHR710)
(710mm long)
5
10
9
6
12
11
87
13
Top/Base (D1574A)
(718 x 494mm) x 3
Left Side (DF2091A)
(1808 x 496mm)
Rail (D1570A)
(718 x 60mm) x 2
Right Side (DF2093A)
(1808 x 496mm)
Door (DF2094A)
(1338 x 355mm) x 2
Vertical Rail (DF2095A)
(1306.5 x 88mm)
Drawer Back (W686-124)
(686 x 124mm) x 2
Drawer Base (T697-367)
(697 x 367mm) x 2
Left Drawer Side (W370-124LH)
(370 x 124mm) x 2
Drawer Front (DF2092A)
(742 x 192mm) x 2
Right Drawer Side (W370-124RH)
(370 x 124mm) x 2
Back (X1779-744)
(1779 x 744mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 20
C
D E F
G
P
H
Small locking nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Drawer runner (F1004) x 4
Large locking nut (F900) x 16
M
I
KJ
9mm Screw (F74) x 4 9mm Screw (F73) x 8
Nail (F51) x 26
L
N
Rail holder
(F1014) x 2
40mm Screw (F910) x 4
13mm Screw (F63) x 14
Hinge (F518) x 6
Hinge plate (F523) x 6
O
Knock-in Peg (F171GY) x 8
Wedgefix (F639) x 8
Plastic Nail (F91) x 4
Q
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
x 2
6
B
B
B
C
C
C
C
7
8
Step 2
Prepare the 2 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
6
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
7
8
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
7 8
6
C
C
7 8
7
8
B
B
6
J
Assembly Instructions
5
Step 4
J
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
10
7 8
6
9
7 8
10
9
9
J
7 8
Step 6
Fit the wedgefixes
Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
F
J
J
F
F
F
F
F
10
7
9
7
8
10
8
6
x 2
x 2
x 2
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
I
P
a:
b:
c:
Prepare the left side
a: Place 2 runners on
the left side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 8 metal
dowels into the left side .
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
1
I
I
B
1
P
P
1
N
L
G
1
N
1
I
P
I
P
1
Finished
front edge
1
I
I
N
N
N
B
B
B
B
B
B
B
B
L
G
1
Assembly Instructions
7
Step 8
Prepare the right side
a: Place 2 runners on
the right side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 8 metal
dowels into the right side .
Push a rail holder into the right side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
2
I
I
B
2
P
P
2
Finished
front edge
I
P
a:
b:
c:
L
2
N
G
2
N
Finished
front edge
I
P
I
P
2
Finished
front edge
2
I
I
Finished
front edge
2
N
N
N
L
G
B
B
B
B
B
B
B
Finished
front edge
Assembly Instructions
8
Step 9
Step 10
Fit the top and a base
Push the top and base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the top and the 2 large locking nuts fitted to the base .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
3
3
2
D
D
3
3
D
Prepare the 3 top and base panels
Tap 2 wooden dowels into each of the top and base panels .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into each of the top and base panels .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
3
D
D
D
D
D
D
Finished
front edge
A
A
10mm
A
x 3
A
3
3
Finished
front edge
3
Finished
front edge
3
2
B
D
Top
Base
E
E
Assembly Instructions
9
Step 11
Fit the rails
Push the rails onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the rails .
4
2
D
4
Step 13
Fit the vertical rail
Attach the vertical rail to the top and base . using 4 screws .
11
3
3
E
3
3
E
E
11
A
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels into each of the rails .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into each of the rails .
A
4
4
D
4
Plain chipboard
surface
x 2
D
Step 12
2
4
4
Assembly Instructions
10
Step 14
Step 15
Fit the other base
Push the other base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
2
Finished
front edge
3
3
2
D
3
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 8 large locking nuts fitted to the 3 top and bases and the 2 rails .
1
D
4
3
1
4
3
3
3
4
Assembly Instructions
11
Step 16
Step 17
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
13
K
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
13
Warning: The unit is heavy. Lift with care.
y
b:
K
y
y
x
x
13
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
Stand the unit up for the next step.
M
1
2
M
M
M
M
1
2
Assembly Instructions
12
Step 18
Step 19
5
L
Fit the hanging rail and drawers
Push the hanging rail into the rail holders fitted to the side panels.
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
5
L
Prepare the 2 doors
Push fit 3 hinges into each of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
90
O
O
12
G
x 2
H
P
P
H
7 8
5
2nd threaded
hole
P
H
H
H
7
8
O
G
G
O
G
G
O
G
G
12
Assembly Instructions
13
Step 20
Fit the 2 doors
Note: The easiest way to attach each door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
O
O
O
N
N
N
O
N
12
a: b:
c: d:
N
O
N
N
B
N
O
O
O
A
O
N
B
12
12
Assembly Instructions
14
Step 19
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
ALR309515
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 20
Fit the overbalance protector
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
Q
Q
Strap
Washer
Screw
TOP OF UNIT
Q
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
Q
Loading...