Argos Denver - 1 Drawer Bedside ASSEMBLY INSTRUCTIONS

Page 1
MADE IN
BRITAIN
Dimensions
Width - 41cm
Depth - 40cm
Height - 49cm
Denver - 1 Drawer Bedside
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/10/14
Important - Please read these instructions fully before starting assembly
352/9045
339/5846
357/9040
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 10kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top/Base (D1560A)
(395 x 395mm) x 2
Left Side (DF1875)
(482 x 396mm)
Right Side (DF1876)
(482 x 396mm)
Drawer Back (W362-124)
(362 x 124mm)
Drawer Base (T373-367)
(373 x 367mm)
Left Drawer Side (W370-124LH)
(370 x 124mm)
Back (X421-399)
(421 x 399mm)
Drawer Front (DF418)
(419 x 192mm)
Right Drawer Side (W370-124RH)
(370 x 124mm)
3
4 5 6
7
8 9
Page 4
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A B
Metal dowel (F901) x 10
C
D E F
G
J
H
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
9mm Screw (F74) x 2 9mm Screw (F73) x 4
Drawer runner (F1004) x 2
Large locking nut (F900) x 8
Nail (F51) x 12
I
Wedgefix (F639) x 2
Plastic Nail (F91) x 4
Knock-in Peg (F171GY) x 4
Page 5
4
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
C
C
5
6
Step 2
Prepare the drawer front
Screw 2 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
4
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
5
6
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
5 6
4
C
C
5 6
5
6
B
B
4
Page 6
Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
8
5 6
4
7
5 6
8
7
7
H
5 6
Step 6
Fit the wedgefixes
Turn the drawer assembly over and slide 2 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
I
H
H
I
I
I
8
5
7
5
6
8
6
4
Page 7
Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
F
J
F
J
Prepare the left side
a: Place a runner on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
Screw 4 metal dowels into the left side .
1
F
F
1
J
J
B
1
a:
b:
F
B
B
B
B
Finished
front edge
Finished
front edge
F
J
Step 8
Prepare the right side
a: Place a runner on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
Screw 4 metal dowels into the right side .
2
F
F
2
J
J
B
2
F
J
Finished
front edge
Finished
front edge
B
B
B
B
F
1
1
2
2
Page 8
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 10
Prepare the top and the base
Insert 4 large locking nuts into the top and 4 into the base .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
D
D
D
3
3
Finished
front edge
D
D
D
D
Finished
front edge
D
D
Fit the top to the right side
Push the top onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the top .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
3
3
2
D
D
Step 11
Fit the base
Push the base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the base .
3
3
2
D
B
D
3
3
3
2
2
3
Page 9
xx
Assembly Instructions
Step 12
8
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and base .
1
3 3
D
1
3
yy
yy
Step 13
b:
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be evenly spaced out.
9
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
G
xx
9
3
Page 10
Assembly Instructions
9
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 14
Step 15
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
Stand the unit up for the next step.
A
1
2
A
A
1
2
A
A
Fit the drawer
Slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
Assembly is complete
E
J
J
E
5 6
2nd threaded
hole
J
E
E
E
5
6
Page 11
Page 12
ALR3093
Page 13
MADE IN
BRITAIN
Dimensions
Width - 75cm
Depth - 40cm
Height - 93cm
Denver - 4 Drawer Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/10/14
Important - Please read these instructions fully before starting assembly
355/8463
332/4790
333/7062
Page 14
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 29kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance kit supplied.
• Dispose of all packaging carefully and responsibly.
Page 15
Components - Panels
Please check you have all the panels listed below
2
1
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
5 6 7
8
9 10
Top (D1567A)
(718 x 395mm)
Left Side (DF2098A)
(930 x 396mm)
4
Drawer Base (T697-367)
(697 x 367mm) x 4
Left Drawer Side (W370-124LH)
(370 x 124mm) x 4
Drawer Front (DF2092A)
(742 x 192mm) x 4
Rail (D1570A)
(718 x 60mm) x 4
Right Drawer Side (W370-124RH)
(370 x 124mm) x 4
Right Side (DF2099A)
(930 x 396mm)
Drawer Back (W686-124)
(686 x 124mm) x 4
Back (X848-744)
(848 x 744mm)
Page 16
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 20
C
D E F
G
J
H
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Small locking nut (F3) x 8
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
9mm Screw (F74) x 8 9mm Screw (F73) x 16
Drawer runner (F1004) x 8
Large locking nut (F900) x 12
Nail (F51) x 20
K
Electric drill (do not use for fitting screws)
I
Wedgefix (F639) x 16
Plastic Nail (F91) x 4
L
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Knock-in Peg (F171GY) x 16
Page 17
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 4
x 4
x 4
x 4
5
B
B
B
C
C
C
C
6
7
Step 2
Prepare the 4 drawer fronts
Screw 2 metal dowels into each of the drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
B
5
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
6
7
Attach the drawer sides to the drawer front
Push the left drawer sides . and right drawer sides . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
6 7
5
C
C
6 7
6
7
B
B
5
Page 18
Assembly Instructions
5
Step 4
H
H
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
9
6 7
5
8
6 7
9
8
8
H
6 7
Step 6
Fit the wedgefixes
Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
K
H
H
K
K
K
K
K
9
6
8
6
7
9
7
5
x 4
x 4
x 4
Page 19
Finished
front edge
Assembly Instructions
6
Step 7
Finished
front edge
F
J
Prepare the left side
a: Place 4 runners on
the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
Screw 6 metal dowels into the left side .
1
F
F
1
J
J
B
1
a:
b:
F
J
F
F
F
F
B
Finished
front edge
F
J
F
J
F
J
B
B
B
B
B
1
1
Finished
front edge
F
J
Step 8
Prepare the right side
a: Place 4 runners on
the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
Screw 6 metal dowels into the right side .
2
F
F
2
J
J
B
2
F
J
F
J
B
F
J
F
J
F
F
F
F
B
B
B
B
B
Finished
front edge
Finished
front edge
2
2
Page 20
A
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 11
Prepare the top
Insert 4 large locking nuts into the top .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
D
D
3
D
D
D
D
Finished
front edge
Step 10
Fit the top to the right side
Push the top onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the top .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
3
3
2
D
D
B
D
3
3
2
D
D
x 4
Prepare the 4 rails
Insert 2 large locking nuts into each of the 4 rails .
Tap 2 wooden dowels into each of the 4 rails .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
D
4
4
A
10mm
A
A
4
Page 21
Assembly Instructions
8
Step 12
Step 13
2
4
4
4
2
Fit 3 of the rails
Push 3 rails onto the right side .
Use a screwdriver to tighten the 3 large locking nuts fitted to the 3 rails .
4
2
D
4
Fit the last rail
Push the last rail onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the last rail .
4
2
D
4
Note: Support this rail until the left side has been fitted in the next step.
4
Step 14
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 6 large locking nuts fitted to the top and rails .
1
D
3 4
4
4
4
4
3
1
Page 22
yy
Assembly Instructions
9
Step 15
Step 16
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be evenly spaced out.
10
G
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
xx
yy
xx
b:
G
10
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
Stand the unit up for the next step.
I
1
2
I
I
I
I
2
1
Page 23
Assembly Instructions
10
Step 17
Fit the drawers
Starting with the bottom drawer, slide both the runners forward and locate the drawer sides . and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
E
J
J
E
76
2nd threaded
hole
J
E
E
E
6
7
Page 24
Assembly Instructions
11 ALR3094
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 14
Fit the overbalance protector
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
L
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
L
L
Example
Screw
(not supplied)
Washer
Screw
UNIT
Page 25
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 28/07/15
Important - Please read these instructions fully before starting assembly
360/2546
359/7596
335/9806
Denver - 3 Door Mirror Robe
Dimensions
Width - 113.5cm
Depth - 50cm
Height - 181cm
Page 26
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 80kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Page 27
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
1 2
3
Shelf (DF2353)
(372 x 470mm) x 3
Left Side (D1575A)
(1808 x 496mm)
Right Side (DF1987)
(1808 x 496mm)
Door
(D1578A)
(1786 x 355mm)
x 2
Vertical Rail
(D1577A)
(1752 x 88mm)
x 2
Small Back
(X1779-391)
(1779 x 391mm)
Large Back
(X1779-737)
(1779 x 737mm)
4
6
Hanging Rail (FHR710)
(710mm long)
7
8 9 11 12
Top/Base (DF1877A)
(1105 x 494mm) x 2
Mirror Door
(D1578MA)
(1786 x 355mm) (Mirror - SG06 1776 x 300mm Safety Back SAR)
10
Horizontal (DF3100A)
(718 x 470mm)
5
Divider (DF2668)
(1753 x 494mm)
Page 28
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 12
C
D E F
G H
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Large locking nut (F900) x 12
M
I
KJ
Nail (F51) x 38
N
Rail holder
(F1014) x 2
40mm Screw (F910) x 12
13mm Screw (F63) x 20
Hinge (F518) x 9
Hinge plate (F523) x 9
Plastic Nail (F91) x 4
Back holder (F276) x 6
Nail screw (F277) x 6
Shelf stud (F110) x 12
L
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Bracket (F945) x 2
O
P
13mm Screw (F79) x 4
Important: Always pair up the hinges with the hinge plates from the same bag. DO NOT mix them up.
Page 29
Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the left side
Screw 6 metal dowels into the left side .
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
B
1
M
K
F
1
M
1
M
B
B
B
B
B
B
M
M
K
F
1
Prepare the right side
Screw 4 metal dowels into the right side .
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
B
2
M
2
B
B
B
M
M
M
B
2
M
Finished
front edge
Page 30
Finished
front edge
Finished
front edge
A
Assembly Instructions
5
Step 3
Step 4
Prepare the 2 top and base panels
Tap 2 wooden dowels into each of the top and base panels .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 4 large locking nuts into each of the top and base panels .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
4
D
D
10mm
A
x 2
A
4
D
D
A
D
D
Finished
front edge
4
4
Base
Fit the top and base
Push the top and base onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the top and the 2 large locking nuts fitted to the base .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
4
4
2
D
D
4
4
D
B
D
Finished
front edge
4
Top
2
Page 31
E
E
E
E
Assembly Instructions
6
Step 5
4
Fit the 2 vertical rails
Attach each of the vertical rails to the top and base using 4 screws .
8
4 4
E
8
8
E
E
4
E
E
Step 6
B
B
M
M
M
Finished
front edge
Prepare the divider
Screw 2 metal dowels into the divider .
Push a rail holder into the divider . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the divider , making sure that the slot is facing towards the finished front edge.
K
F
3
3
K
F
B
M
3
3
Page 32
E
Assembly Instructions
Step 7
Step 8
4
E
E
E
4
3
Fit the divider
Attach the divider to the top and base using 4 screws .
3
4 4
E
4
Prepare the horizontal
Tap 2 wooden dowels into the horizontal .
Insert 4 large locking nuts into the horizontal .
5
D
D
D
D
D
Finished
front edge
A
A
A
5
5
7
Page 33
Assembly Instructions
8
Step 9
44
4
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 6 large locking nuts fitted to the top , base and the horizontal .
1
D
5
4 4
1
5
Step 10
Finished
front edge
4
3
5
Fit the horizontal
Push the horizontal onto the divider .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
5
3
D
5
Page 34
Assembly Instructions
9
Step 11
4
Fit the brackets
a: Fit a bracket up
against the divider and rail about 900mm from the top using 2 screws .
b: Fit a bracket up
against the horizontal and rail using 2 screws .
J
J
J
J
1
2
4
1
5
8
P
P
O
8
O
3
8
P
O
5
8
P
3
O
O
P
P
O
Step 12
Fit the 4 plastic nails
Tap 2 plastic nails into the bottom edge of each of the sides and . .
J
1
2
a:
b:
900mm
Page 35
Assembly Instructions
10
Step 13
yy
yy
4
Fit the back panels
a: Square up the unit by
making sure that measurement x:x equals
y:y.
Place the small back and large back down, onto the unit as shown.
Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the divider’s back edge.
b: Nail around the
outside edges of the 2 backs.
Note: Do not nail where the 2 backs meet and nails should be spaced about 150mm apart.
c: Push the 5 nail
screws through the 5 back holders and tap them down between the small back and large back and into the back edge of the divider . .
Keep tapping the nail screws in until the back holders dig into the small and large back.
Stand the unit up for the next step.
11
12
I
G
H
11
12
3
G
H
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
Note: If ever you need to take the backs off to dismantle the unit, the nail screws can be taken out using a screwdriver.
G
H
c:
G
H
11
12
H
HG
+
b:
I
xx
xx
11
12
Warning: The unit is heavy. Lift with care.
Page 36
Assembly Instructions
11
Step 14
Step 15
90
N
N
F
F
N
F
F
N
F
F
9
x 2
Prepare the 3 doors
Lay the doors down onto a soft, smooth surface.
Push fit 3 hinges into each plain door and the mirror door .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the front edge of the door.
F
N
9
10
Warning: Glass! Handle with care
N
F
F
N
F
F
N
F
F
10
x 1
Fit the hanging rail and shelves
Push the hanging rail into the rail holders fitted to the side panels.
For each of the 3 shelves , insert 4 shelf studs .
Lower the 3 shelves down onto the shelf studs .
7
K
7
C
x 4
C
x 4
C
x 4
6
6
6
6
C
6
C
7
K
Page 37
Assembly Instructions
12
Step 16
Fit the 3 doors
Note: The easiest way to attach each door and is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
N
N
N
M
M
M
N
M
9
a: b:
c: d:
M
N
M
M
B
M
N
N
N
A
N
M
B
9
10
9
10
Page 38
Assembly Instructions
13
Step 17
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
b:
c:
d:
a:
A
A
B
C
Page 39
Assembly Instructions
14
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 18
Fit the overbalance protector
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit . fitted to the unit or, an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
L
L
Strap
Washer
Screw
TOP OF UNIT
L
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
L
Page 40
ALR3096
IMPORTANT INFORMATION ABOUT THIS PRODUCT
This product complies with the requirements of BS 7449:1991 and has been
manufactured by
DECORATIVE PANELS FURNITURE LTD, TEESSIDE
INDUSTRIAL ESTATE, THORNABY-ON-TEES, CLEVELAND, TS17 9LT
.
The product code for this unit and the item code(s) for the glass
components are listed in the Assembly Instructions along with a description
of the type of glass used. All clear/tinted glass complies with the
requirements of BS 6206 Class A. All mirrors comply with the requirements
of BS 6206 Class C. If the glass component contained in this unit is chipped
or broken consult the furniture manufacturer, retailer, or agent with regard to
obtaining a manufacturing specification and shape for replacement glass
quoting the unit description and batch number or date of manufacture.
Do not place very hot or very cold items against or in close proximity to
glass surface(s) unless adequately thick insulating material is used to
prevent such items coming in contact with the glass.
Do not strike the glass with hard or pointed items. Do not sit or stand upon horizontal glass surfaces.
When cleaning glass panels use a damp cloth or leather with washing up
liquid or soft soap if necessary - do not use washing powders or any other
substance containing abrasives since these substances scratch glass.
If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.
KEEP THESE INSTRUCTIONS FOR FUTURE USE
Loading...