Argos Dalton - Bookcase ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 72cm
Depth - 33cm
Height - 183cm
Dalton - Bookcase
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 24/09/13
Important - Please read these instructions fully before starting assembly
609/6788
142/9790
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 30kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
9
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D1792A)
(718 x 328mm)
Shelf (D1795A)
(556 x 284mm) x 4
Plinth (D1797A)
(556 x 95mm) x 2
Left Side (D1793A)
(1808 x 290mm)
2
12
10
Right Side (D1794A)
(1808 x 290mm)
11
8
Fascia (D1799A)
(1808 x 70mm) x 2
Drawer Front (D1798A)
(550 x 162mm)
Drawer Base (T564)
(533 x 197mm)
Back (X919)
(1592 x 584mm)
Drawer Back (W564)
(522 x 115mm)
Left Drawer Side (W454LH)
(200 x 115mm)
Right Drawer Side (W454RH)
(200 x 115mm)
3
4
5
6
7
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 30
C
D
Large locking nut (F900) x 28
H
19mm Screw (F461) x 2
I
Small locking nut (F3) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
G
N
13mm Screw (F79) x 1
E
Nail (F51) x 30
M
Drawer runner (F307) x 2
J K
9mm Screw (F74) x 2
9mm Screw (F73) x 4
40mm Screw (F910) x 4
L
Bracket (F327) x 1
Knock-in Peg (F171) x 4
F
Handle (F287) x 1
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
Step 2
Prepare the drawer front
Screw 2 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
B
4
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and right drawer side .
Note: Arrow on locking nut must point towards hole in edge of panel.
Step 3
D
5
6
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
5 6
4
D
D
5 6
D
B
B
D
D
5
6
Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.
B
B
D
4
5
6
Small groove
4
Assembly Instructions
5
Step 4
F
F
4
Attach the handle
Attach the handle to the drawer front using 2 screws .
N
H
Step 6
4
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and .
Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
8
5 6
4
7
5 6
8
7
7
F
5 6
6
4
5
6
F
F
8
7
5
8
H
H
4
N
Assembly Instructions
6
Step 7
Prepare the left side
a: Insert 4 large locking
nuts into the left side . .
Note: The arrow on the locking nuts must point towards the holes in the edge of the panel.
Turn the left side over
b: Place a runner
onto the left side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
c: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
d: Screw 10 metal
dowels into the left side .
K
M
M
9
K
M
K
K
M
B
9
9
K
B
B
B
B
B
B
B
B
B
B
C
9
9
9
9
b:
a:
c:
d:
C
9
Turn the left
side over
C
C
C
C
Assembly Instructions
7
Step 8
a:
b:
c:
K
M
K
K
B
B
B
B
B
B
B
B
B
B
10
10
10
C
C
C
10
Prepare the right side
a: Insert 4 large locking
nuts into the right side .
Note: The arrow on the locking nuts must point towards the holes in the edge of the panel.
Turn the right side over
b: Place a runner
onto the right side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
c: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
d: Screw 10 metal
dowels into the right side .
M
10
K
M
K
B
10
10
C
10
Turn the right
side over
C
C
A
Assembly Instructions
8
Step 9
Prepare the 2 fascias
Screw 4 metal dowels into each of the 2 fascias . .
Tap a wooden dowel into each of the 2 fascias . .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
B
11
11
B
B
B
B
A
B
B
B
Left side fascia ­holes nearest this side.
Right side fascia ­holes nearest this side.
The runner is at this end.
Join the left side to the left side fascia
a: Push the left side
down onto the left side fascia panel .
b: Use a screwdriver to
tighten the 4 large locking nuts fitted to the left side .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
9
11
C
9
C
11
11
Step 10
a:
b:
A
10
10
Dowel
this end
11
11
9
9
B
C
Assembly Instructions
9
Step 11
Step 12
Prepare the 4 shelves
Insert 4 large locking nuts into each of the 4 shelves .
C
2
C
C
C
C
Finished
front edge
x 4
2
Join the right side to the right side fascia
Push the right side down onto the right side fascia panel .
Use a screwdriver to tighten the 4 large locking nuts fitted to the right side .
10
11
C
10
The runner is at this end.
10
Dowel
this end
11
10
Assembly Instructions
10
Step 13
Step 15
Fit the plinths
Push the 2 plinths onto the right side .
Use a screwdriver to tighten the large locking nut fitted to each plinth .
Step 14
C
3
10
3
3
10
3
A
C
C
A
Prepare the plinths
Tap 2 wooden dowels into each of the plinths . .
Insert 2 large locking nuts into each of the plinths .
3
3
A
C
Plain chipboard
surface
3
x 2
Finished
front edge
Finished
front edge
Finished
front edge
Fit the shelves
Push the 4 shelves onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to each shelf .
C
2
10
2
10
2
2
2
2
Finished
front edge
Note: Support the plinths until the left side has been fitted in the next step.
G
G
G
G
Assembly Instructions
11
Step 16
Step 17
Fit the left side
Push the left side onto the assembly.
Use a screwdriver to tighten the 10 large locking nuts fitted to the 4 shelves and the 2 plinths .
C
9
2
3
3
3
2
2
2
2
9
Fit the top
Attach the top to the unit using 4 screws .
1
G
1
y
Assembly Instructions
12
Step 18
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
12
E
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
12
y
y
x
x
b:
E
Warning: The unit is heavy. Lift with care.
12
Assembly Instructions
13
Step 19
2nd threaded
hole
M
J
Fit the drawer
Slide both of the runners . forward and locate the drawer sides and . between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the hole in the runner.
Note: Do not overtighten the screws. If they catch on the runner you may need to loosen them slightly.
M
J
5
6
M
J
J
5
6
Assembly Instructions
14
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 20
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.
Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.
Swivel the bracket back and fix the bracket to the wall, then tighten Screw .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Warning: The unit is heavy. Lift with care.
Assembly is complete
L
L
I
L
L
I
L
I
L
L
ALR2814
Loading...