MADE IN
BRITAIN
Dimensions
Width - 84.5cm
Depth - 50cm
Height - 182cm
Dalton - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/04/14
Important - Please read these instructions fully before starting assembly
228/5713
248/4040
245/8186
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 44.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
2
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
6
Left End (DF708)
(1800 x 465mm)
Top (DF710)
(843 x 496mm)
Base (DF715)
(809 x 457mm)
Rail (DF713)
(809 x 80mm) x 2
Palister (DF714)
(1800 x 88mm) x 2
5
3
Back (DF716)
(1731 x 835mm)
Right End (DF709)
(1800 x 465mm)
8 Door (DF711)
(1714 x 328mm) x 2
9
Hanging Rail (FHR801)
(801mm long)
7
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 22
C
D E F
G H I
L
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
M
J K
N
Large locking
nut (F900) x 22
Nail (F51) x 34
19mm Screw (F461) x 4
Plastic Nail (F91) x 4
13mm Screw (F79) x 1 13mm Screw (F63) x 14 Shelf stud (F110) x 2
Bracket (F327) x 1
Handle (F287) x 2
Rail holder
(F1014) x 2
Hinge Plate
(F325) x 6
Hinge Arm
(F324) x 6
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the left end
Tap a wooden dowel
into the left end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 7 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw 4 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
Push a rail holder into
the left end . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
B
1
C
1
10mm
A
1
A
C
C
C
C
C
C
C
C
C
B
B
B
B
B
Prepare the right end
Tap a wooden dowel
into the right end .
Insert 7 large locking
nuts into the
right end .
Screw 4 metal dowels
into the right end .
Push a rail holder into
the right end and
then secure with screw .
B
2
C
2
2
A
Step 2
C
C
C
C
C
C
C
B
B
B
B
1
2
J
H
J
1
H
J
2
H
J
H
Assembly Instructions
5
Prepare the 2 pallisters
a: Tap 2 wooden dowels
. into the top end of 1
of the pallisters .
Fit 3 hinge plates to
this pallister using
the upper pair of holes.
Screw 5 metal dowels
into the pallister .
b: Tap 2 wooden dowels
. into the bottom end
of the other pallister .
Fit 3 hinge plates to
this pallister using
the lower pair of holes.
Screw 5 metal dowels
into the pallister .
Step 3
B
B
B
B
B
M
M
M
B
B
B
B
B
M
M
M
A
6
6
6
Upper pair of holes
Dowels this end
Lower pair of holes
A
A
Dowels this end
A
A
b:
a:
M
B
A
6
6
6
M
B
M
M
6
6
Assembly Instructions
6
Step 4
Fit a pallister to the
left end
Push the correct pallister
. onto the left end .
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the left end .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
6 1
1
C
B
C
C
Dowels this end
6
1
Dowels this end
6
2
Step 5
Fit a pallister to the
right end
Push the correct pallister
. onto the right end .
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the right end .
6 2
2
C
Finished
front edge
A
Prepare the base
Insert 4 large locking
nuts into the base .
C
4
Assembly Instructions
7
Step 6
C
C
C
C
Finished
front edge
4
Step 7
Fit the base to the
right end
Push the base onto
the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Step 8
4
2
4
C
C
C
A
Prepare the 2 rails
Insert 2 large locking
nuts into each of the
2 rails .
Tap 2 wooden dowels
into each of the 2 rails .
C
5
5
A
5
x 2
4
2
Assembly Instructions
8
Step 9
Fit the rails to the
right end
Push the 2 rails onto
the right end .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the rails .
Step 10
2
5
5
5
2
C
5
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and the 2
rails .
1
C
5
5
5
1
4
4
Prepare the top
Screw 4 metal dowels
into the top .
Assembly Instructions
9
Step 11
B
B
B
B
Finished
front edge
B
3
Step 12
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and right
end .
3
C
2
1
2
1
1
2
Step 13
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
E
1
2
E
E
E
E
3
Finished
front edge
yy
xx
Assembly Instructions
10
Step 14
Step 15
yy
2
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
9
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
b:
D
xx
9
Warning: The
unit is heavy.
Lift with care.
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
7
J
7
7
J
Assembly Instructions
11
Step 16
Step 17
I
I
Fit the shelf studs
Push the 2 shelf studs
up into the holes in the
top to act as door
buffers.
I
3
Prepare the doors
Push fit 3 hinges into
each of the 2 doors .
Secure each hinge
with 2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
8
N
N
H
N
H
H
N
H
H
N
H
H
90
N
Note: To make it easier
to fit the hinges, rest
the doors on something
to raise them up.
8
3
x 2
Assembly Instructions
12
Step 18
Fit the doors
2 people are needed
here
The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
To seperate the Hinge Arm and Plate
press the button at the end of the Arm,
and lift the Hinge Arm off the Plate.
CLICK
LIFT
Locate the hooks on the
Hinge Arm underneath the
front of the Hinge Plate.
The Hinge Arm must be
flat against the Hinge Plate
prior to any adjustment.
Press the front of the Hinge Arm
down onto the Hinge Plate until
it ‘CLICKS’ into place.
a: b:
c: d:
N
M
M
M
M
N
N
N
8
8
8
Assembly Instructions
13
Step 19
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the top (or
base) of the unit is level,
front-to-back and sideto-side in the 3 positions
shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
14
Step 20
Fit the handles
Attach a handle to
each door using 2
screws .
L
F
8
F
F
L
L
8
8
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3040
Step 21
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the
bracket fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screw will
depend on the distance
from the back of the unit
to the wall.
Fix the bracket
loosely onto the top of
the unit using screw
and mark the wall for the
wall fixing.
Swivel the bracket
away from the wall and
drill a hole in the wall
using a suitable drill bit
and fit your wall fixing.
Swivel the bracket
back and fix the bracket
to the wall, then tighten
screw .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Warning: The
unit is heavy.
Lift with care.
Assembly is complete
K
K
G
K
K
G
K
G
K
K
Loading...