MADE IN
BRITAIN
Dimensions
Width - 49.5cm
Depth - 40cm
Height - 49cm
Dalton - 1 Door Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 09/05/14
Important - Please read these instructions fully before starting assembly
238/4638
248/5094
238/5297
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 12kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Components - Panels
Please check you have all the panels listed below
2
1
Right Side (D0273A)
(399 x 353mm)
2
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Pilaster (DF691)
(467 x 88mm) x 2
Left End (DF857)
(467 x 365mm)
Base (DF860)
(460 x 354mm)
Plinth (DF690)
(460 x 80mm)
Door (DF859)
(381 x 310mm)
Shelf (DF861)
(460 x 354mm)
4
5
8
6
7
9
Top (DF688)
(494 x 396mm)
Back (X486-396)
(486 x 396mm)
Please check you have all the fittings listed below
Tools required
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 16
C
D E F
G H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Large locking
nut (F900) x 16
Nail (F51) x 12
19mm Screw (F461) x 2
Plastic Nail (F91) x 4
13mm Screw (F63) x 4 Shelf stud (F110) x 4
Handle (F287) x 1
K
Hinge Plate
(F325) x 2
Hinge Arm
(F324) x 2
A
A
C
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the left end
Tap 2 wooden dowels
into the left end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 5 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw 3 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
B
1
C
1
10mm
A
1
A
C
C
B
Prepare the right end
Tap 2 wooden dowels
into the right end .
Insert 5 large locking
nuts into the
right end .
Screw 3 metal dowels
into the right end .
B
2
C
2
2
A
Step 2
C
C
C
B
B
B
C
C
1
C
C
C
C
B
B
B
2
Assembly Instructions
5
Step 3
Finished
front edge
A
A
Prepare the base
Tap 4 wooden dowels
into the base .
Insert 4 large locking
nuts into the base .
C
4
Step 4
Fit the base to the
right end
Push the base onto
the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 5
4
2
4
C
C
Prepare the plinth
Insert 2 large locking
nuts into the plinth .
Tap 2 wooden dowels
into the plinth .
C
6
6
A
C
C
C
C
Finished
front edge
A
A
4
2
A
C
C
6
4
A
B
C
Assembly Instructions
6
Step 6
Fit the plinth to the
right end
Push the plinth onto
the right end .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
Step 7
6
2
C
6
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the base and the
plinth .
Step 8
1
C
6
4
6
2
1
6
4
B
B
B
B
Prepare the top
Screw 4 metal dowels
into the top .
B
3
Finished
front edge
Assembly Instructions
7
Step 9
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and right
end .
3
C
2
1
Step 10
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
E
1
2
3
2
1
E
E
E
E
2
1
Assembly Instructions
8
Step 11
Step 12
yy
xx
yy
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
9
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
b:
D
xx
9
Prepare the door
Push fit the 3 hinges
into the door .
Secure each hinge
with 2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
8
K
K
H
K
H
H
90
K
Note: To make it easier
to fit the hinges, rest
the door on something
to raise it up.
K
H
H
8
Assembly Instructions
9
Step 13
Prepare the 2 pallisters
a: Fit 2 hinge plates
to one of the pallisters .
Screw 3 metal dowels
into the pallister .
b: Screw 3 metal dowels
. into the other pallister
. .
6
6
6
J
B
B
B
B
B
J
J
B
B
B
J
a:
b:
Fit the door to the
pallister
2 people are needed
here
Fit the door to the
pallister with the
hinge plates .
8
7
Step 14
J
8
7
To seperate the Hinge Arm and Plate
press the button at the end of the Arm,
and lift the Hinge Arm off the Plate.
CLICK
Locate the hooks on the
Hinge Arm underneath the
front of the Hinge Plate.
The Hinge Arm must be
flat against the Hinge Plate
prior to any adjustment.
Press the front of the Hinge Arm
down onto the Hinge Plate until
it ‘CLICKS’ into place.
a: b:
c: d:
K
J
J
J
J
K
K
K
LIFT
Assembly Instructions
10
Step 15
Insert the shelf
Place the shelf into
the unit to rest on the
base .
5
4
5
4
Step 16
Fit the door pallister
Push the pallister with
the door attached
onto the right side .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the right side .
7
8
2
C
2
7
8
2
Assembly Instructions
11
Step 17
Fit the other pallister
Push the other pallister
onto the left side .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the left side .
7
1
C
1
7
1
1
Fit the shelf
Lift the shelf up and
insert 4 shelf studs at
the required height.
Lower the shelf down
onto the shelf studs .
I
x 4
Step 18
I
I
5
5
5
Assembly Instructions
12
Step 19
1
Fit the handle
Attach the handle to
the door using 2
screws .
G
F
8
F
F
G
8
Assembly Instructions
13
Step 20
Adjust the door if
needed
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, frontto-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
14
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 21
Assembly is complete
ALR3038
Loading...